Jaguar XK engine tappet shims
Discussion
A bit of help please from the Jaguar experts out there, I'am looking for someone to measure the diameter of the valve tappet shims in the Jaguar XK engine. I'am after a shim to fit in a 17.50mm recess so looking for one with an outside diameter of 17.46mm. I've been told the ones in the Jaguar XK engine are this size but have been unable to get confirmation from anywhere so far.
Any help greatly appreciated, I'am trying to find a source of new shims to replace the existing Maserati ones, thickness not important at this stage.
Ciao
Chad
Any help greatly appreciated, I'am trying to find a source of new shims to replace the existing Maserati ones, thickness not important at this stage.
Ciao
Chad
v8250 said:
Chadspeed, just checked my Jaguar ref' books but they don't include the data you need. Suggest give VSE a call - sure they'll be able to help
VSE
Powys, Wales, UK
Call: +44 (0)1597 840308
Email: vse.uk@virgin.net
Web: http://www.vse-engines.com/
Alternatively, get some off the shelf shims from a good auto-engineering Co'. You could try these guys...
http://www.arrowprecision.com/14-shims
I know Arrow quire well and they don't stock flat shims, they need an order of at least 200 to manufacture, very helpful guys though.VSE
Powys, Wales, UK
Call: +44 (0)1597 840308
Email: vse.uk@virgin.net
Web: http://www.vse-engines.com/
Alternatively, get some off the shelf shims from a good auto-engineering Co'. You could try these guys...
http://www.arrowprecision.com/14-shims
Edited by v8250 on Thursday 24th April 18:16
I'll give VSE a call tomorrow, hope they can help.
Cheers
mph said:
Found the following excerpt from a thread on valve shims which may be helpful
"As far as I'm aware most of the old Imperial engines like the Jag, Lotus, Imp etc used 5/8" (15.875mm, 0.625") diameter shims.
Aftermarket suppliers then made these as 15.55mm diameter shims to allow them to also fit other engines including the Saab 99 and 900, Maestro and Montego 1.7 and 2.0, and Rover 2.3, 2.6 engines "
Thanks MPH"As far as I'm aware most of the old Imperial engines like the Jag, Lotus, Imp etc used 5/8" (15.875mm, 0.625") diameter shims.
Aftermarket suppliers then made these as 15.55mm diameter shims to allow them to also fit other engines including the Saab 99 and 900, Maestro and Montego 1.7 and 2.0, and Rover 2.3, 2.6 engines "
I found that thread also but further down the page the OP who was looking for 17.5mm shims posted :
'XK engines have larger shims but the general view is the smaller dia ones
will be ok.
I managed to source and have ground, cheaply, XK shims - which was handy.'
So a bit confusing really.
a8hex, your offer to actually measure some would be very useful - thanks
--
mph said:
The point being there is more than one diameter of XK shim in use and it appears that the "genuine" ones will be too big for your requirements.
Ok, I didn't get that impression from the thread, just that they were either 17.5mm or smaller. When I do get to the bottom of it I'll let you know.Edited by mph on Friday 25th April 10:26
VSE Engines closed on Fridays so that line of enquiry will have to wait.
V8 FOU said:
I have built / rebuilt many XK engines, and they have always had 5/8" shims. Just measured an E type head to confirm that.
Shims aren't too difficult to make. I have made them out of tool steel and ground to thickness in the past.
PaulShims aren't too difficult to make. I have made them out of tool steel and ground to thickness in the past.
Thank you very much for taking the time to do that, seems I'll have to continue the hunt. I am an Engineer as well but no longer work at a place with a machine shop so making shims will be a last resort. Maserati always did like to do things differently, sometimes it seems for the sake of it.
Chad
Just found these:
http://www.ebay.com/itm/MASERATI-V8-DOHC-GHIBLI-BO...
Could save some effort if not £
http://www.ebay.com/itm/MASERATI-V8-DOHC-GHIBLI-BO...
Could save some effort if not £
Rolymo, 5/8" shims definitely wont fit the V8 so no use to me I'am afraid, however sounds like lotus-types may have a use for them.
lotus-types, 17.30-17.38mm seems too small by a few thou, no idea what they are from but again thanks for the offer. It could be they would work but I've found a good alternative solution.
I have ordered 16 different thickness shims from Heinz at HJM Imports in Wisconsin USA for $10 each plus $11 for shipping so about £102 total. Heinz assures me they are hardened so seems like a fair deal, having used ones ground to a different size would surely cost more than £6 each.
http://www.ebay.com/itm/MASERATI-V8-DOHC-GHIBLI-BO...
When they arrive in about 2 weeks I'll let you know.
Chad
lotus-types, 17.30-17.38mm seems too small by a few thou, no idea what they are from but again thanks for the offer. It could be they would work but I've found a good alternative solution.
I have ordered 16 different thickness shims from Heinz at HJM Imports in Wisconsin USA for $10 each plus $11 for shipping so about £102 total. Heinz assures me they are hardened so seems like a fair deal, having used ones ground to a different size would surely cost more than £6 each.
http://www.ebay.com/itm/MASERATI-V8-DOHC-GHIBLI-BO...
When they arrive in about 2 weeks I'll let you know.
Chad
Gassing Station | Classic Cars and Yesterday's Heroes | Top of Page | What's New | My Stuff