Springtime - stone chip repairs!
Discussion
Quinny said:
Of course.... When I'm 100% happy I'll either scan or photograph it and email it to you.... If that doesn't work I'll send you a card template....
Just let me make sure it's a good enough fit.
I would appreciate that very much! I'm a computer graphics artist by trade, so I can create an Illustrator/PDF/Photoshop template from whatever you provide--whatever works for you.Just let me make sure it's a good enough fit.
Quinny said:
Yes, I think you're right.... I probably put the paint on a bit to heavy.... I'm goingbto try a slightly different method tomorrow..
There's a definite and obvious improvement, and I'm not expecting miracles... But I would like to get a more even coverage and hide a bit more of the white...
Do bear in mind, that my garage is extremely well lit, the car is a eye level and the camera was in Macro...
With the car on the floor, and a couple of paces back, it showed a significant improvement.... Not as good as I'd like, but a bit more patience and practice, should yield good results...
Then I need to figure out how to apply the Armourfend and how far up the flank I should go...
Save me reading through the whole thread, dDoes the kit come with clear coat and rubbing compound?There's a definite and obvious improvement, and I'm not expecting miracles... But I would like to get a more even coverage and hide a bit more of the white...
Do bear in mind, that my garage is extremely well lit, the car is a eye level and the camera was in Macro...
With the car on the floor, and a couple of paces back, it showed a significant improvement.... Not as good as I'd like, but a bit more patience and practice, should yield good results...
Then I need to figure out how to apply the Armourfend and how far up the flank I should go...
The biggest issue is the surface is not paint but clear coat. Filling completely with paint will never match it.
So ideally you need to do the following;
Properly clean out the chips
Touch in with well mixed paint below the level of the clear coat
Build up the chip with clear coat to just above
(now the brave bit) flat out the humps with very very fine wet & dry
Polish out with rubbing compound to blend in to clear coat around it
On applying the PPF a few tips!
get a spray bottle with 1% detergent in distilled water
spray body work
spray out side of film
peel backing and spray glue side as you go
from one point lay the soaking film on to the soaking body work to "float" it
Push any large air bubbles to the edge
Make sure it is where you want it
Use a small rubber blade to push liquid & air out hte edges & dry as you go
Leave to set!
BTW best not to do the PPF film until the chip fixing is well and truly set
UPDATE
Just had word from Chipex that only 14 orders have been received against this offer.
We did commit to 20 names to get the deal. Chipex have done their part by giving the % so it would be great if we could fulfill ours...
It would be a shame if our credibility suffered because of this and it jeopardised future arrangements either with this - or other businesses - if the word got around that we hadn't done the bis!
Just had word from Chipex that only 14 orders have been received against this offer.
We did commit to 20 names to get the deal. Chipex have done their part by giving the % so it would be great if we could fulfill ours...
It would be a shame if our credibility suffered because of this and it jeopardised future arrangements either with this - or other businesses - if the word got around that we hadn't done the bis!
oblio said:
UPDATE
Just had word from Chipex that only 14 orders have been received against this offer.
We did commit to 20 names to get the deal. Chipex have done their part by giving the % so it would be great if we could fulfill ours...
It would be a shame if our credibility suffered because of this and it jeopardised future arrangements either with this - or other businesses - if the word got around that we hadn't done the bis!
I agree - maybe start a new list of 'who has ordered?!' - (I've got mine by the way).Just had word from Chipex that only 14 orders have been received against this offer.
We did commit to 20 names to get the deal. Chipex have done their part by giving the % so it would be great if we could fulfill ours...
It would be a shame if our credibility suffered because of this and it jeopardised future arrangements either with this - or other businesses - if the word got around that we hadn't done the bis!
Gassing Station | Aston Martin | Top of Page | What's New | My Stuff