Centre caps for these wheels??
Discussion
Hi
Does anyone else have these wheels and know what centre caps dims are right? I measured the dia of the wheel centre hole, ordered accordingly 48mm dia and they were a few mm too loose.
Also the clip depth would be good know too if anyone's ordered for these before.
Just dont want to keep ordering and returning trial and error.
Cheers
Does anyone else have these wheels and know what centre caps dims are right? I measured the dia of the wheel centre hole, ordered accordingly 48mm dia and they were a few mm too loose.
Also the clip depth would be good know too if anyone's ordered for these before.
Just dont want to keep ordering and returning trial and error.
Cheers
Hi
Its these that I ordered which don't fit.
https://www.amazon.co.uk/dp/B00V0HJXFU/ref=pe_3857...
Its says 48 & 60 mm dia on the cap. That's the weird bit as the dia on the diagram on the webpage shows this as slightly smaller . Either way its too small for the centre hole of the wheel.
Its these that I ordered which don't fit.
https://www.amazon.co.uk/dp/B00V0HJXFU/ref=pe_3857...
Its says 48 & 60 mm dia on the cap. That's the weird bit as the dia on the diagram on the webpage shows this as slightly smaller . Either way its too small for the centre hole of the wheel.
gizzardio said:
Its says 48 & 60 mm dia on the cap. That's the weird bit as the dia on the diagram on the webpage shows this as slightly smaller . Either way its too small for the centre hole of the wheel.
46.5mm isn't going to stay in a 48mm hole!For the number of times you'll need to remove them you could silicone 'em in?
I have these wheels! And a green S (albeit with 2 less cylinders...). There aren't many of the S cars with these wheels - the Wedges had something similar but a 5 stud wheel.
They have the centre caps in them, but they're pretty chewed up so was planning on replacing them. Will be at the car this weekend so will try and get one out and take some measurements. Hopefully report back next week!
Andrew
They have the centre caps in them, but they're pretty chewed up so was planning on replacing them. Will be at the car this weekend so will try and get one out and take some measurements. Hopefully report back next week!
Andrew
Apologies...but better late than never!!
I've popped one of mine off today and I measure 48mm inner and 52mm outer diameter, Fortunately mine are in quite good condition, I'm going to order some 46mm TVR logos to stick over the outside to tidy them up.
Pictures below - hope this helps or if you have already sorted then info is here next time someone wants!
Andrew
IMG_4351
IMG_4348
I've popped one of mine off today and I measure 48mm inner and 52mm outer diameter, Fortunately mine are in quite good condition, I'm going to order some 46mm TVR logos to stick over the outside to tidy them up.
Pictures below - hope this helps or if you have already sorted then info is here next time someone wants!
Andrew
IMG_4351
IMG_4348
Hi
Thanks for checking. Weirdest thing. That's what I had ordered apparently, to fit a 48mm hole. But they measure 46mm across that same dimension as you measured.
I might just try siliconing them in now as I don't want to order another set of "48mm" to receive the same again.
If you find where yours are from or know where I can try, like you know the original wheel name and model ref I could try with them.
Cheers
Thanks for checking. Weirdest thing. That's what I had ordered apparently, to fit a 48mm hole. But they measure 46mm across that same dimension as you measured.
I might just try siliconing them in now as I don't want to order another set of "48mm" to receive the same again.
If you find where yours are from or know where I can try, like you know the original wheel name and model ref I could try with them.
Cheers
Gassing Station | S Series | Top of Page | What's New | My Stuff