glass runner

[HOTTY]

Took my 400se down for a MOT, passed

Two years its sat in the garage i had forgotten that the passenger side glass runner was shagged. Opening the window. it dropped down, luckily didn't break but does anyone know were i can get one from. (or what they are off)

Got the BAR run next weekend and it gets cold up-norf

cheers
hotty

[Mike Brewer]

Great news on the 400 .Good on you ....Mike .

[mrzigazaga]

Well done mate...Enjoy...

[pasogrande]

Stephen,

Wish I could help with your question. I need the horizontal piece at the bottom of the glass, which has a bit of rubber like a bicycle inner tube to hold the glass. On the same side (which we call driver's side over here).

You are probably looking for the vertical runner on the front edge.

I hope somebody has an answer.

Wilf.

[plasticpig72]

sorry Steve, off subject but could you pm me ref reveneer dash. Sorry again Alan

[stevoj]

Well done with MOT, feels good don't it

[wooly350i]

Check out land rover defender runners, they are similar if not the same, think I saw some on Rimmer Bros

[marcus1875]

Would a 280 fhc fit? If so i'm sure i have a spare at the garage. I'll check tomorrow.
Marcus

[HOTTY]

pasogrande said:

Stephen,

Wish I could help with your question. I need the horizontal piece at the bottom of the glass, which has a bit of rubber like a bicycle inner tube to hold the glass. On the same side (which we call driver's side over here).

You are probably looking for the vertical runner on the front edge.

I hope somebody has an answer.

Wilf.

Hi Wilf

Same thing i am looking for, metal bit at the bottom with the rubber bit in holding the glass, sounds like Marcus may have one, fingers crossed

Thanks to all regarding enjoying, mind you the very dusty 400 had me going......last night and this morning could get the main beam and flash working, ran out of time and drove there hoping for stevie Wonder tester, no got the up-start, younger that the car and good at his job....crap but the wedge gods looked down and blessed me, it only all start to flipping work (how luckily)

cheers
hotty

Alan - sorry will message you regarding the veneers but not asked the CNC company if still possible yet.

[mrzigazaga]

If not then i think Grimmers sell them...I need to replace my driver side...
This is what it looked like in March 2014...I just covered it in oil and forgot about it...Guess the time has come..


Thanks for reminding me...

[HOTTY]

mrzigazaga said:

If not then i think Grimmers sell them...I need to replace my driver side...
This is what it looked like in March 2014...I just covered it in oil and forgot about it...Guess the time has come..


Thanks for reminding me...

Mark must be the only crusty thing on Poppy but that's it, glass holder with the runner fixed. You know the code i need ?

[mrzigazaga]

There are a couple of crusty bits on Poppy but that is by far the worst..

There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well

Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P

[wooly350i]

mrzigazaga said:

There are a couple of crusty bits on Poppy but that is by far the worst..

There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well

Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P

That's wot I said!!

[HOTTY]

mrzigazaga said:

There are a couple of crusty bits on Poppy but that is by far the worst..

There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well

Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P

Cheers Mark

Expensive but ordered as no time to muck about with only a few working days before the mini rusty

[mike various]

I've bought some defender ones for my fhc,
You can buy the same thing cheaper off the land rover websites.
Rimmers are quite expensive !!
Get part number, google it and you can find the part a lot cheaper,
I think I paid £9 each. Can check tomorrow when I get home.

Mike

[pasogrande]

Thanks Mark and others for the info.

Are driver side and passenger side same?

Wilf.

[mrzigazaga]

pasogrande said:

Thanks Mark and others for the info.

Are driver side and passenger side same?

Wilf.

Hi Wilf...As far as i know they are....


Ziga

[marcus1875]

Sorry not got one. I've sparr mechs and motors but not the runner :-(
Sorry
Marcus

[GOG440]

Really really important question here.

How the bloody hell do you get the glass back in the runners? mine fell out last year and the glass is sat in the bottom of the door and I cant get the bloody thing back in.

[HOTTY]

GOG440 said:

Really really important question here.

How the bloody hell do you get the glass back in the runners? mine fell out last year and the glass is sat in the bottom of the door and I cant get the bloody thing back in.

my experience that the runner/glass holder has to come out, you may have to pinch the metal to ensure it grips before you tap back onto the glass (the dirt will help to locate in the correct position), pop it back on the scisser arm and lube up.......the glass runner at the side