Discussion
Took my 400se down for a MOT, passed
Two years its sat in the garage i had forgotten that the passenger side glass runner was shagged. Opening the window. it dropped down, luckily didn't break but does anyone know were i can get one from. (or what they are off)
Got the BAR run next weekend and it gets cold up-norf
cheers
hotty
Two years its sat in the garage i had forgotten that the passenger side glass runner was shagged. Opening the window. it dropped down, luckily didn't break but does anyone know were i can get one from. (or what they are off)
Got the BAR run next weekend and it gets cold up-norf
cheers
hotty
Stephen,
Wish I could help with your question. I need the horizontal piece at the bottom of the glass, which has a bit of rubber like a bicycle inner tube to hold the glass. On the same side (which we call driver's side over here).
You are probably looking for the vertical runner on the front edge.
I hope somebody has an answer.
Wilf.
Wish I could help with your question. I need the horizontal piece at the bottom of the glass, which has a bit of rubber like a bicycle inner tube to hold the glass. On the same side (which we call driver's side over here).
You are probably looking for the vertical runner on the front edge.
I hope somebody has an answer.
Wilf.
pasogrande said:
Stephen,
Wish I could help with your question. I need the horizontal piece at the bottom of the glass, which has a bit of rubber like a bicycle inner tube to hold the glass. On the same side (which we call driver's side over here).
You are probably looking for the vertical runner on the front edge.
I hope somebody has an answer.
Wilf.
Hi WilfWish I could help with your question. I need the horizontal piece at the bottom of the glass, which has a bit of rubber like a bicycle inner tube to hold the glass. On the same side (which we call driver's side over here).
You are probably looking for the vertical runner on the front edge.
I hope somebody has an answer.
Wilf.
Same thing i am looking for, metal bit at the bottom with the rubber bit in holding the glass, sounds like Marcus may have one, fingers crossed
Thanks to all regarding enjoying, mind you the very dusty 400 had me going......last night and this morning could get the main beam and flash working, ran out of time and drove there hoping for stevie Wonder tester, no got the up-start, younger that the car and good at his job....crap but the wedge gods looked down and blessed me, it only all start to flipping work (how luckily)
cheers
hotty
Alan - sorry will message you regarding the veneers but not asked the CNC company if still possible yet.
mrzigazaga said:
If not then i think Grimmers sell them...I need to replace my driver side...
This is what it looked like in March 2014...I just covered it in oil and forgot about it...Guess the time has come..
Thanks for reminding me...
Mark must be the only crusty thing on Poppy but that's it, glass holder with the runner fixed. You know the code i need ? This is what it looked like in March 2014...I just covered it in oil and forgot about it...Guess the time has come..
Thanks for reminding me...
There are a couple of crusty bits on Poppy but that is by far the worst..
There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well
Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P
There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well
Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P
mrzigazaga said:
There are a couple of crusty bits on Poppy but that is by far the worst..
There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well
Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P
That's wot I said!!There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well
Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P
mrzigazaga said:
There are a couple of crusty bits on Poppy but that is by far the worst..
There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well
Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P
Cheers Mark
Expensive but ordered as no time to muck about with only a few working days before the mini rusty
There are a couple of options...
Original
http://www.rimmerbros.co.uk/Item--i-MUC2322
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2322P
They have a runner rubber seal as well
Original
http://www.rimmerbros.co.uk/Item--i-MUC2325
Aftermarket
http://www.rimmerbros.co.uk/Item--i-MUC2325P
Cheers Mark
Expensive but ordered as no time to muck about with only a few working days before the mini rusty
GOG440 said:
Really really important question here.
How the bloody hell do you get the glass back in the runners? mine fell out last year and the glass is sat in the bottom of the door and I cant get the bloody thing back in.
my experience that the runner/glass holder has to come out, you may have to pinch the metal to ensure it grips before you tap back onto the glass (the dirt will help to locate in the correct position), pop it back on the scisser arm and lube up.......the glass runner at the sideHow the bloody hell do you get the glass back in the runners? mine fell out last year and the glass is sat in the bottom of the door and I cant get the bloody thing back in.
Gassing Station | Wedges | Top of Page | What's New | My Stuff