Project Scimitar MV6

Project Scimitar MV6

Author
Discussion

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 6th October 2013
quotequote all
All done and back in the car now.



I'm thinking of doing something similar with the diagonal down bars next and even some mounts for the door bars, maybe.

But now the fun is over, I've got to do some work frown

More to come

lozzzzzz

Original Poster:

339 posts

156 months

Friday 18th October 2013
quotequote all
I've been trying to make another way of silencing the car a little more for the long boring journeys and this is what I came up with.







Hopefully you can tell from the photos that these get pushed into the exhausts and mean the gas has to take a torturous route to get out. Restictive yes, but removable too smile The hope was that the gas will have to go up the center of the first section of perforated tube, out through the walls to the surroundings then back into the perforated tube before coming out the back.

Bit like this:


But guess what..... it hasn't wo... well its the best thing yet but it still isn't killing the drone.

lozzzzzz

Original Poster:

339 posts

156 months

Friday 18th October 2013
quotequote all
Right then, this wire wool is really doing the trick smile . I've no doubt its restricting the hell out of it, but it really has made it quiet smilesmilesmilesmilesmilesmilesmile

And its easily removed smilesmile

Its not the neatest, but I now have a direction to head in making something better in the future.

First I cut the ends off, so its a much shorted perforated tube now, and with one blocked end


Then cut up some perforated ends to stop the wire wool blowing out, I even drilled the holes out in an attempt to make is slightly less restrictive.



Then I went and bought the Co-op supply of scourer's (sp?) and filled up the tubes.


Drilled some holes and popped some rivnuts in and hey presto!



More to come.

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 27th October 2013
quotequote all
I've really started ripping into the electrics now, I've made all the changes to the central dash, and all of the bits that needed changing on the drivers side, and I'm in the midst of opening up the bulk of the loom on the passenger side now. I'm basically giving everything that has anything to do with the ECU an earth on the "busbar". And hopefully that'll cure the earth loop problems. I've got a fairly good idea of the problem now, after much reading and sifting through various webpages.

This is the busbar:


This is where its going:


And this is the mess as it stands at the moment:


Apart from the busbar, the other changes are to get rid of the Map switch and have it auto switch to Map2 when the LPG solenoids open, bin the fuel pump switches as they have to be on all the time anyway (even when on gas), and add an LPG momentary kill switch. This will serve two purposes, firstly ont he very rare occasion the LPG plays up it'll mean I don't have to switch the engine off to reset the LPG ecu, and secondly (and more cool), it'll give a 20s go on petrol then switch back to gas, good for overtaking when lots of power is needed.

More to come

lozzzzzz

Original Poster:

339 posts

156 months

Tuesday 5th November 2013
quotequote all
These arrived yesterday, so I'll get them fitted when I'm done with the wiring, then when I can find the time to go get the front springs the handling should stand a chance of being ok smile

I requested they make them 1" shorter this means I can raise the exhaust and hopefully have less exhaust road contact smile


Meanwhile, the wiring still looks like this smile


More to come

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 10th November 2013
quotequote all
This won't pick up pace for about a year yet but the supercharged 3.2 project has officially begun. I've bought a 3.2 engine (with forged crank) and conveniently an R30 gearbox smile

Thing is its completely covered in car at the moment smile



Anyway off the garage for more Scimitar wiring.

More to come

itsrodders

212 posts

184 months

Monday 11th November 2013
quotequote all
Busy Busy, Loz!

Enjoying as always.

I presume that the 3.2s/c is destined for for the Scim? woohoo

lozzzzzz

Original Poster:

339 posts

156 months

Tuesday 12th November 2013
quotequote all
You got it! I'll do the engine rebuild slowly over the next year and put the supercharged engine in the Scim this time next year. The 3.2 has a forged crankshaft and the obvious larger capacity making it ideal for supercharging, it also has the benefit of a stronger gearbox.


BigTom85

1,927 posts

170 months

Wednesday 13th November 2013
quotequote all
Fantastic stuff indeed. Still following with interest...

Not sure the supercharger is really necessary, but hell, why not!!! smile

Keep up the good work mate.

lozzzzzz

Original Poster:

339 posts

156 months

Thursday 14th November 2013
quotequote all
You know the saying.

If it ain't broke..... modify it

(I've just got to fix the broken bits first smile )

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 17th November 2013
quotequote all
I've finally had a good day on the car, its been a while since I've had a good long sesh in the garage, but yesterday I got all the earth's properly attached to the busbar with crimped and soldered ring terminals.


The moment of truth arrived as I started the car and attached the laptop to see the inputs on screen. The car started really quickly (not sure if that related really) and the inputs were rock steady, the temp input was the worst and used to jump all over the place by 10 degrees now there is no movement at all, it just stays on one number and clicks up to the next as the engine warms up. BRILLIANT!!!!!!! very happy with that smile I'll get the car mapped again when its back on the road and have the gas mapped properly too.

Next was to change the piddling earth straps for one big sealed 35mm^2 earth strap, I had to take the exhaust manifold off for this which was a bit of a pain, but all went well.


And then I got round to fitting the new GAZ rear units. GAZ made them shorter by 1" as requested so the axle is over an inch higher on full droop, this means the exhausts can be raised and will hopefully stop hitting the road when I drive through a dip in the road.


I tried adjusting the exhausts but I'm asking too much by just loosening the clamps and re-tightening in a different position so I'll have to cut and shut them next.

More to come

lozzzzzz

Original Poster:

339 posts

156 months

Wednesday 20th November 2013
quotequote all
I had a little while in the garage this evening and got the exhausts raised, which involved cutting a small section out, bending the gap shut and welding it up again in SS. The lowest point in now 35mm higher than it was smile .

It look s better too, with the exhaust being just 1cm or two below the lowest part of the chassis now:



Very happy with that, hopefully no more horrible scraping noises and sparks out the back.

Next is to change the clutch reservoir hose again, (still haven't found anything that stands up to brake fluid, next thing to try nylon with SS over-braid, I'm hopeful with this one.

Then fit new front springs, sort the petrol gauge (which seems to be sticking on empty and only occasionally telling the truth), then faff on with the fuel filler cap to try stopping it pressurising the tank, then.... It's ready to be taxed again and sent off for cage making smile

More to come.

lozzzzzz

Original Poster:

339 posts

156 months

Friday 22nd November 2013
quotequote all
These updates are getting less and less interesting, It used to be I've made new suspension wishbone and my own manifolds, well last night folks, in the hour I had working on the car,

I changed the clutch hose... Another job ticked off the list though.

Here is the old one, its turned the fluid black and you can see the DOT4 "sweating" through the hose:


Now it looks like this:


More to come (hopefully more exciting)

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 24th November 2013
quotequote all
Yesterday was fuel tank day. I had to sort the fuel gauge problem. While I was messing about looking around the fuel tank i noticed a stain that looked as though it had been leaking. It would make sense for a weak point to have been found as the tank had been pressurising. So off came the bumper and the tank.

The bumper was easy, there were captive bolts and other things making it easy that I'd forgot I'd done, and light clusters came off with 4 screws and one waterproof multiplug smilesmile
You can see evidence of the tank leak:


I pressurised the tank and put soapy water on and found a simgle point leak. Reasonably easy to fix smile I've heard of connecting it to the exhaust of another car to ensure it doesn't blow up in your face so I gave that a go, it worked (I'm still breathing) but it did put a lot of water into the tank from condensation:


Its repaired now, all welded up. Oh and the sender problem was easy, the float has a hole in it and was was full of petrol making it more of a "sink". This meant I'd kept putting petrol in the tank worrying that it was empty, so when I came to empty the tank there was s**t loads in there! I look 10 cans to empty it. There was a right panic moment when all four cans were full and I went to put the plug back in, petrol flowing everywhere, all down my arm and I'm fumbling with freezing hands that don't work properly!
Oh yeah I was saying, I robbed the float from the latest Omega smile and grafted in on to the Scimitar sender:


More to come

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 1st December 2013
quotequote all
I've had a good morning stripping the MV6 of everything I could while keeping it running in preparation for the engine removal, the car looked a bit like this when finished this afternoon.



More to come

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 8th December 2013
quotequote all
Here's is a picture speaking 1000 words. I'm very pleased with today's efforts smile



More to come

lozzzzzz

Original Poster:

339 posts

156 months

Wednesday 18th December 2013
quotequote all
A little update.

The car is booked in for cage fitting in mid January, and I've penciled in the idea of a track day at Bedford Autodrome on the 22nd March. I was nervous just considering it. I've had the car 8 years and been doing this latest major project nearly 4 years, the thought of.... well the unthinkable happening is terrifying, but this was always the end goal so here goes smile

I was working through the list last night and got to the point where there was nothing left to do but change the gearbox (something I've been putting off).

The current GB works, but is the R28, with an apparent oil leak under hard acceleration and a gear linkage problem. I've got the stronger R30 to fit (I wanted this done in time for the track day) and with a fully working gear linkage.

So I studied the new gearbox to try and understand the oil leak problem and its become apparent that it's not a "leak" really. In the Scim the acceleration is rather more rapid than in an Omega and the oil swills to the back of the box, so much so that it poors out of the breather (which is right at the back, see photos). Great design that! Thing is it only happens when the box is more than 45 degrees which must mean the Scim is pulling more than 1G in acceleration in 1st gear!!!

I did a few calcs based on the 0-60 being 5.5s or less and it might very well be pulling more than 1G in 1st gear.... cool!!!

But annoying for the gearbox "leak"

Anyway, here is the fix I've come up with. It saves drilling and getting swarf in the box. It's not ideal but certainly can't make it worse, and it might even work a bit smilesmile (I'll bee keeping an eye on the oil level)



With the breather extended forward so much it can pull 80G and won't poor out.

After faffing around with that a bit I only got as far as taking the prop off and gearbox mount, so more to come on the gear box change.

lozzzzzz

Original Poster:

339 posts

156 months

Wednesday 18th December 2013
quotequote all
Perhaps I should add to this and say that the copper pipe will be secured before the gearbox is fitted.

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 22nd December 2013
quotequote all
An update on the project......

I've had a very productive last few days on the car. It got the point where there was little left to do but change the gearbox over for the stronger R30. While I was at it, I took the opportunity to remove the hydraulic handbrake and extend it a little, I also shortened the gearstick and removed any rubber coupling (quickshift you might call it).

Refitting the gearbox was a hard task, lying under the car with the thing on my chest, but its all back together and the feel of the gear change is quite rewarding smile







I'm really looking forward to driving it again soon, there have been a good number of improvements since its first 6 months on the road.

More to come

lozzzzzz

Original Poster:

339 posts

156 months

Sunday 5th January 2014
quotequote all
A long overdue update.....

I've brought the date forward for the first trackday. It seems its a lot cheaper in Feb rather than March so 22nd of Feb it is at the Bedford Autodrome! Cant' Wait!

The last things on the list are the half cage and the seats. I had the car booked in to have a cage made over a week, this would mean leaving it somewhere for a week! Something I've not done in all 8 years of ownership. More importantly as I'd be at work, I wouldn't be part of the decision making process. I rang around and found that TR Lane could fit me in so I went with the car for a Saturday morning. I was able to hang around, and help a bit, and be part of the decisions. Much happier with that. As an added bonus he cut and bent the tubes, and welded the hoop only in, and I'll be doing the rest of the welding and painting smilesmilesmile Much better! And Much MUCH CHEAPER smilesmilesmile (all the following for £150).

So here is what I had after my visit


And the other bits


I'm really pleased, there is a bit of a gap either side to accommodate the seat belt but its snug against the roof. There will be two rear stays and one cross bar in the main hoop. The rear stays will be attached using a method he suggested. This starts with a welded in washer in an offcut of the tube. (then I faced it up of the lathe).



And they will be bolted to the chassis like this

The finished mount will be of this style


I also finally got round to fitting a little box in the center for sun glasses and such.


That's all for now, lots of welding to do now and hopefully fitting of bucket seats. Talking of which I need some seat runners if anyone has any.

More to come