E36 shreading inner rear tyres
Discussion
Hi guys,
I stuck some new road rubber on the E36 awhile back and have managed all of 2 trackdays on them, 1 dry day at castle combe and 1 wet day at Llandow and i've had a quick look at the tyres and noticed it's shreadded the insides of the rears, they are practically bold with the outside of the tyre looking unused!
If this just down the the ride height change?
Do i need to get an adjustable rear tie bar and have the camber adjusted to compensate?
I stuck some new road rubber on the E36 awhile back and have managed all of 2 trackdays on them, 1 dry day at castle combe and 1 wet day at Llandow and i've had a quick look at the tyres and noticed it's shreadded the insides of the rears, they are practically bold with the outside of the tyre looking unused!
If this just down the the ride height change?
Do i need to get an adjustable rear tie bar and have the camber adjusted to compensate?
bulldog5046 said:
Any idea of what degree of camber would be acceptable?
Depends on how much inside tyre wear you can live with.My road car is only at about -1.5 degrees and that probably wears the inside edge by about 2mm more than the outside edge over the course of it's life. i.e. when the inside is needing replacement, the outside still has 3.5-4mm.
If you add further negative camber then you'll get even more uneven wear.
My answer would be either to spend the money and get it appropriately set up with whatever parts are required by a shop that knows their E36 track cars or to reverse whatever you did to lower it. How much camber to run depends on the tyres, pressures, driving style and suspension setup so there is no simple answer to that question. The baseline is that you need enough camber to not roll over the shoulders of the tyre and probably not any more if you are running standard road rubber. It is equally possible that the answer might be that you need to drive faster
I'm picturing a barried up E36 .
Seriously though, a good tyre fitter will be able to tell you your current toe, camber, and the rest. You can go from there to getting it back near to factory settings. Or, say, find out what the M3 has and get it set the same. How low is this thing? Pics!
Seriously though, a good tyre fitter will be able to tell you your current toe, camber, and the rest. You can go from there to getting it back near to factory settings. Or, say, find out what the M3 has and get it set the same. How low is this thing? Pics!
Pentoman said:
I'm picturing a barried up E36 .
Seriously though, a good tyre fitter will be able to tell you your current toe, camber, and the rest. You can go from there to getting it back near to factory settings. Or, say, find out what the M3 has and get it set the same. How low is this thing? Pics!
Oi! it's not.Seriously though, a good tyre fitter will be able to tell you your current toe, camber, and the rest. You can go from there to getting it back near to factory settings. Or, say, find out what the M3 has and get it set the same. How low is this thing? Pics!
When fund's allow i'll get the adjustable arms and 4 wheel alignment, i guess that will sort it out?
Ooook that's very nice
In answer to your question, Camber and to a lesser extent Toe angles effect handling and tyre wear and once appropriately set-up your car will handle better and use it's tyres properly. Perhaps someone in one of the BMW racing championships can furnish you with some recommendations for these values as a starting point?
In answer to your question, Camber and to a lesser extent Toe angles effect handling and tyre wear and once appropriately set-up your car will handle better and use it's tyres properly. Perhaps someone in one of the BMW racing championships can furnish you with some recommendations for these values as a starting point?
There is a limited amount of camber adjustment at the rear via an eccentric bolt on the lower arm. This will probably be seized solid unless someone has dealt with it already.
After that it is adjustable camber arms (cheap and cheerful steel ones on ebay or nicer alloy ones from the likes of Eibach cost a lot more)
After that it is adjustable camber arms (cheap and cheerful steel ones on ebay or nicer alloy ones from the likes of Eibach cost a lot more)
drjhill said:
There is a limited amount of camber adjustment at the rear via an eccentric bolt on the lower arm. This will probably be seized solid unless someone has dealt with it already.
After that it is adjustable camber arms (cheap and cheerful steel ones on ebay or nicer alloy ones from the likes of Eibach cost a lot more)
Ahh, thats useful to know, i thought the standard were fixed position.After that it is adjustable camber arms (cheap and cheerful steel ones on ebay or nicer alloy ones from the likes of Eibach cost a lot more)
I'll see if i can loosen off the bolts before i go out buying new arms then
Cheers!
You can get upto 1.5deg neg on the Stock arms, top & bottom bushes can limit that if fooked. Ive never yet run aftermarket arms, found enough in the standard oneș, can weld them for ștrength tho, Slicks do put străin on them.
its not camber thats causing yr issue it would take about 8 deg to shred inner edge on track, ive run 3.6 & no îșsues, its ăs Shim says toe that needs looking at.
its not camber thats causing yr issue it would take about 8 deg to shred inner edge on track, ive run 3.6 & no îșsues, its ăs Shim says toe that needs looking at.
weed said:
Have you had the rear toe settings checked. Sounds like it has excessive toe out.
m
This.m
It was toe out that did similar to front tyres on my car (outside barely worn, inside down to carcass after 5000 miles), not the camber.
Get an alignment/geo done now, otherwise, you'll spend more than that on replacement tyres.
On my car it was caused by the previous owner replacing wishbones or track rods by himself and not getting an alignment done afterwards.
braddo said:
weed said:
Have you had the rear toe settings checked. Sounds like it has excessive toe out.
m
This.m
It was toe out that did similar to front tyres on my car (outside barely worn, inside down to carcass after 5000 miles), not the camber.
Get an alignment/geo done now, otherwise, you'll spend more than that on replacement tyres.
On my car it was caused by the previous owner replacing wishbones or track rods by himself and not getting an alignment done afterwards.
Trev450 said:
If this is the case then the car would be oversteering like crazy. Is that the case OP?
No, it's very well balanced in the dry.Understeers in the wey in slow corners and oversteers in fast corners, but i'd expect that from a RWD car.
Is the rear toe even adjustable on these?
Gassing Station | Track Days | Top of Page | What's New | My Stuff