|
BornAgainGT
Original Poster
44 posts
43 months
|
 Side pods positioned (not final fitted), exhaust headers in place  Wheel speed sensors fitted  Straight thru exhaust for those VERY rare indeed none limited days  Silenced exhaust for all other times  Rear wing and more detail of the exhaust hangers  Rear end coming together now
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Splitter end fences added  Air box  Throttle body trumpets  Rolling again  Rolling again  Rolling again
|
|
|
ellis427
1,581 posts
48 months
|
|
|
kybo
897 posts
64 months
|
Fantastic project. Awesome rebuild.
Looking forward to the next installment.
How much time has it taken, so far?
Thanks,
Scott
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Heat protection and drive shafts installed  Heat protection and drive shafts installed
|
Advertisement
|
|
|
Ferb
3,110 posts
79 months
|
I like it  You should also put this thread in readers cars section as well  Good work  I used to hillclimb a Chevron B54 with a 6.3 chev in the back (625bhp) it was lot's of fun 
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Completed front end  Completed front end  Air intake base plate preperation  Air intake base plate preperation  Air intake base plate  Close up
|
|
|
jonka
254 posts
87 months
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Splitting the back end to finalise the clutch solution  From another angle
|
|
|
vetteheadracer
8,123 posts
122 months
|
Great project, look forward to seeing it finished.
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Scratch build wiring loom based around DTA electronics.  Laying out the dash controls  Locating the ECU leaving room for the GCU  Newly powder coated rims mounted  Newly powder coated rims mounted  Getting there  Getting there  Getting there  Currently 633KG
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Completed the machining of the top front engine mount  Shown installed  Powder coated rear wing pylons, air box base  Safety wire nuts
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Many , many hours of work preparing the body work to take carbon wrap  Base wrap complete, just coloured highlights to add
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
 Final fit of the side pods and center section around the roll bar hoop  High level view of same, showing relief for the seat belt pickups  And low level from the side  Could not resist fitting front and rear sections - just to see what she looked like - very pleased  And from high level - again very pleased with the overall look  And finally from the side Best get her finished then, the track is beckoning...
|
|
|
kybo
897 posts
64 months
|
Ouch,
That is awesome!!
Any details yet on when/where you'll be testing her or what events you'll be racing in - I would love to see/hear her doing some aggresive laps.
Thanks for the updates.
Scott
|
|
|
A Curtis
115 posts
37 months
|
Cracking thread!
Is all the body work fibreglass with a carbon wrap?
|
|
|
thechosenfamily
230 posts
24 months
|
Awesome thread mate.
And by the way awesome car
|
|
|
xr287
820 posts
49 months
|
Brilliant thread! It's nice to see how it all goes together.
|
|
|
Secret Lemonade
213 posts
52 months
|
i see this could be making an apperance at snetterton on august 14
|
|
|
BornAgainGT
Original Poster
44 posts
43 months
|
Back again - been a while but good progress  Body shell removed again and final fit of clutch solution  Release bearing  Gear shift mechanism fitted  Transaxle oil cooler fitted  Build up of the induction system  Induction system complete - bar air box base plate  Fuel system complete
|
|
