They say it cannot be done - 1000bhp Supercharged VXR8

[HappyMidget]

[HappyMidget]

Suspension is in the country and covered by warranty. Getting fixed the Monday after TR.

Meanwhile, contemplating just fitting the injectors and overdrive pulley and saving cam and springs till later so I can actually measure the changes each component makes just to satisfy my curiosity. Also working on shielding the intake as this weather is killing it.

[HappyMidget]

178mh at Thunder Road yesterday, shame it was my 6th run and didn't count for the official prize for being the fastest https://www.youtube.com/watch?v=mikEQuifE2w

Gonna be fun next year if I get a job to cover fitting costs.

[Janosh]

Nice improvement on last year

Just looked at the results from TR - what gave you the extra 10mph trap speed on the 6th run?

[HappyMidget]

Janosh said:

Nice improvement on last year

Just looked at the results from TR - what gave you the extra 10mph trap speed on the 6th run?

Not sure, think tyre pressures were right up, the air temp dropped and I actually hit all my shifts.

[anonymous-user]

Thought it's time to check how many HPs you've yet to find. Surely it must be close now? The suspense is killing me!!

[PH XKR]

He's closer to actual 650hp than your elanor car with its Mark scribbled a number on a bit of paper print out.

[anonymous-user]

PH XKR said:

He's closer to actual 650hp than your elanor car with its Mark scribbled a number on a bit of paper print out.

That literally makes no sense. Try some punctuation...and maybe adding a few more words.

[chuntington101]

Eaton have just release d the TVS 2650. It's said to flow 25% more air than the 2300! Should be the first eaton that can easily push over 1000bhp! The aftermarket guys already have them but nothing GM out yet (although Magnuson have a nice dodge setup with twin throttle bodies!!).

[HappyMidget]

chuntington101 said:

Eaton have just release d the TVS 2650. It's said to flow 25% more air than the 2300! Should be the first eaton that can easily push over 1000bhp! The aftermarket guys already have them but nothing GM out yet (although Magnuson have a nice dodge setup with twin throttle bodies!!).

I still prefer the screw type to the PD type due to the internal compression ratio of the screws compared to just the manifold compression of a PD.

Build has been on hold due to my new job meaning the car is my DD. On holiday over Xmas so may get the chance to send the car off to get the parts fitted.

[chuntington101]

HappyMidget said:

chuntington101 said:

Eaton have just release d the TVS 2650. It's said to flow 25% more air than the 2300! Should be the first eaton that can easily push over 1000bhp! The aftermarket guys already have them but nothing GM out yet (although Magnuson have a nice dodge setup with twin throttle bodies!!).

I still prefer the screw type to the PD type due to the internal compression ratio of the screws compared to just the manifold compression of a PD.

Build has been on hold due to my new job meaning the car is my DD. On holiday over Xmas so may get the chance to send the car off to get the parts fitted.

The TVS 2650 will outflow the 2.9 and thus run cooler. The other whipple option would be the front feed 4.5 that they are supposed to be releasing. That will definitely reach you goals with loads of room the spare!

[HappyMidget]

chuntington101 said:

The TVS 2650 will outflow the 2.9 and thus run cooler. The other whipple option would be the front feed 4.5 that they are supposed to be releasing. That will definitely reach you goals with loads of room the spare!

Will prob run an interchiller anyway but a front feed 4.3 would definitely fit the bill The 2.9 is in range for the target though at the end of the day and I have seen that the HB do suffer from cracked casings due to the extreme temps pushed at them.

[HappyMidget]

A bit of thread necromancy, but hey, all good fun

Finally got round to fitting the following parts and had it tuned:

BTR stage 3 blower cam (231/248 .617"/.595" 120+5)
IWIS TIMING CHAIN
LS CHROMOLY PUSHROD SET (5/16") 7.4"
BTR .660" Dual Spring Kit Ti Retainers
BTR Front Timing Cover Gasket
BTR Timing Chain Damper Seal
BTR Water Pump Gasket
ARP Crankshaft Damper Bolt
GM 3 Bolt 4 Pole Cam Gear
ARP Cam Bolts
BTR Valve Cover Gaskets
BTR header gaskets
Lingenfelter Harmonic Balancer
Lingenfelter 22% OD Pulley
Lingenfelter Idler pulley relocation bracket
ID850 Injectors
Lingenfelter Cold Air Intake
Pacemaker 2" Ceramic coated Long Tube headers
Pacemaker 100 cell sports cats
Pacemaker 3" catback exhaust





This was set up on the Dyno at Surrey Rolling Road using BP Ultimate on stock fuel pump and spark plugs. There is plenty left in the tune for more power but stopped the tuning at this point. No hint of knocking or fuel delivery issues. 1000BHP doesn't seem so far off with some better cooling/knock prevention

[anonymous-user]

wouldn't race fuel run it to 1000bhp?

Good you are getting there.

[HappyMidget]

The Spruce goose said:

wouldn't race fuel run it to 1000bhp?

Good you are getting there.

Pretty much with the extra timing that could be added. Should be able to get there on 97 though

Unlike most V8's tuned over here, you would not know how powerful it is until I put my foot down, no cold start issues, no lumpy idle, no shunting in traffic.

[HappyMidget]

I love how well this car drives now, all that extra torque makes driving so effortless

[Jimbo NW]

Any pictures of the actual build OP, read that whole thread and no pictures!

[HappyMidget]

Errrm, good point. Picture a stock VXR8 and then you have mine on the outside Will see if I can get the pictures of the engine when it was in the garage from my mechanic

Have a picture of me and my dog in front of it for now

[HappyMidget]

[dom9]

Did they clean up the weld in that collector?

Looking good - must be a proper rocket now!

Have a look in Events and head back to the next Surrey meet - would be great to see it now.

(and you, Swerni)