350i foot mats

[plasticpig72]

well i haven't picked up my car yet but i would like to know where to buy Foot Mats for a 350i Wedge.
When i go to England to pick up the Wedge i would like to do a bit of Wedge shopping.
Carpets and maybe Veneer for the Dashboard.
Open to suggestions
Alan

[TVRleigh_BBWR]

Mark Zig on here has started to make the Mats.

Currently they no supply of Veneer, but there is a company that do a very good stick on Vinyl veneer, I was skeptical but was very impressed.

[plasticpig72]

I saw something on a past blog with "HOTTY" and i think he did a Veneer on his Silver 350i.
I have e-mailed him but no reply for the moment. Wait and see
Alan

[stevoj]

TVRleigh_BBWR said:

Mark Zig on here has started to make the Mats.

Currently they no supply of Veneer, but there is a company that do a very good stick on Vinyl veneer, I was skeptical but was very impressed.

I was impressed with a stick on job i saw at BBWF, anyone know where its available?

[mrzigazaga]

stevoj said:

TVRleigh_BBWR said:

Mark Zig on here has started to make the Mats.

Currently they no supply of Veneer, but there is a company that do a very good stick on Vinyl veneer, I was skeptical but was very impressed.

I was impressed with a stick on job i saw at BBWF, anyone know where its available?

Hi...I think someone on FB used a pre-sized piece of plastic veneer and cut that to fit which looked quite impressive...Ill copy the pic and post it as i don't think the guy is on PH.

Im not sure where mine were from but they are a stick on by the look of it...Don't think these were a "Hotty dash"



Im making Wedge over mats for my Wedge friends so if you could email me i can explain what i can do...Or i can PM you.

Thanks

Ziga

[Grady]

This guy always has listings on ebay. They look nice but I've never seen one in person.

http://www.ebay.com/itm/TVR-280i-5-piece-wood-set-...

There were some threads about shop in the UK that everyone though well of. But beyond my PH searching skills. Grady

[plasticpig72]

hi Ziga,
i have e-mailed about matts and i must say the Dashboard does look tasty also
Alan

[mrzigazaga]

plasticpig72 said:

hi Ziga,
i have e-mailed about matts and i must say the Dashboard does look tasty also
Alan

You have 2 x Mails...

[plasticpig72]

yep thanks,
just sent reply. You have some very nice bits of kit there
Alan

[Nick Brough]

mrzigazaga said:

Hi...I think someone on FB used a pre-sized piece of plastic veneer and cut that to fit which looked quite impressive...Ill copy the pic and post it as i don't think the guy is on PH.


Thanks

Ziga

He did a very good job the veneer came from here

http://www.vinylwarehouse.co.uk/67cm-red-maple-mid...

I also bought one of these for my glove box http://tvr-parts.com/tvr-parts/part-details/tvr-02...


Nick

Edited by Nick Brough on Sunday 1st May 00:13

[pasogrande]

Just wondering if the veneers work for both RHD and LHD cars.

Wilf.

[mrzigazaga]

pasogrande said:

Just wondering if the veneers work for both RHD and LHD cars.

Wilf.

Hi Wilf...I should think so as its a sheet of self adhesive vinyl so is not handed...I think you will need to remove the veneer or whats left of it so that you have a flat surface to stick it to...The holes are then cut out....Although I'm not sure if you cut them as they appear or cross cut to fold behind the openings?...Guess it doesn't matter if you have bezels to go in there afterwards...


Cheers


Ziga

[Hayduke]

mrzigazaga said:

pasogrande said:

Just wondering if the veneers work for both RHD and LHD cars.

Wilf.

Hi Wilf...I should think so as its a sheet of self adhesive vinyl so is not handed...I think you will need to remove the veneer or whats left of it so that you have a flat surface to stick it to...The holes are then cut out....Although I'm not sure if you cut them as they appear or cross cut to fold behind the openings?...Guess it doesn't matter if you have bezels to go in there afterwards...


Cheers


Ziga

[/wiseacre mode on = default]
Just rotate the LHD dash panel 180 degrees for RHD, apply veneer, then rotate back 180 degrees for LHD. Install the 'clocks' in their LHD orientation.