WRX RA powered VW 1303 beetle cabrio with a bit of Porsche

WRX RA powered VW 1303 beetle cabrio with a bit of Porsche

Author
Discussion

ricola

Original Poster:

468 posts

276 months

Saturday 1st November 2014
quotequote all
Time for a mini project! A while back during the MOT test I was slightly concerned with how much the wheels moved about when the tester spread the front axle on the pads. Having seen a few designs of A arms at Spa and online on the boxergasse forum I've decided to give it a go myself! I wanted to do it as a completely bolt on swap. Part of this change is to de-couple the stock anti-roll bar from the geometry so this will be spaced down underneath the A arm. I've seen people put it above but my radiator is in the way and I have plenty of ground clearance.
The inner spherical joint will be M10 and the forward tension link section will be M14, I will also be using sealed boots to keep them weather tight. At the spindle I'm using the original design ball joint. Some people re-position the lower axis as they run very low.

Before I took the stock suspension off, I put the car on stands and with the steering dead ahead and a vertical level marked up the position to the floor. This is obviously just to get the geometry about right, I can fine tune it afterwards.


The key part to the swap is creating a forward bracket, this aluminium block spaces the anti-roll bar downwards with the stock saddle clamp and gives plenty of meat to mount the forward joint.


The block fitted, not how it is fitted to the chassis form. My mate, Seb, machined up some tube end fittings for it.


The first lateral link tacked together


and fitted to the car, now to align the hub and measure up for the tension link. The last bit will be to work out how to connect the anti-roll bar.


Tension link tacked in at nominal geometry position. Some people will fit a clevis type joint to the lateral part but I only wanted minimal adjustment. Welded will give better stiffness.


I trawled ebay for a nice short anti-roll bar that I thought I could adapt and ended up with this from a Mk2 Ford Mondeo, less than £5 delivered for the pair! It was a case of making up some fairly simple adapters to bolt on to the standard 1303 anti-roll bar ends.


Brackets to weld on to the new A arms


Finished A arm ready for paint


Finished 'kit' ready to be fitted! Note I did machine down the blocks some more compared to earlier pictures to maintain the stock pick up position heights and maximise ground clearance.


Ball joint pressed in and rod ends adjusted with their rubber boots to give them a bit more life


All done!


Closer view of one side..


So, the verdict: in summary well worth it! The front end feels so much more alive and communicative but NVH is hardly affected at all. The tyres seem to work a lot better as they are not moving around so much and the steering is even a bit lighter too. Even on motorways you can feel what's going on with the most subtle of movements. Overall it just gives so much more confidence in what the car i doing and that means a lot!

For anybody else that wants to try something similar this is what I used:

Inner joints: M10 male rod ends with high misalignment spacers

Forward joints: M14 rod ends with standard misalignment spacer, additional 18mm spacer inboard

Stock lower strut ball joints

1 1/2" diameter 0.1" wall thickness CDS tubing

Mk 2 Ford Mondeo/Cougar rear anti-roll bar links

If you can't work out the rest then frankly you probably shouldn't be trying to copy it!!

Oh, I know it's short notice but I'll be in it tomorrow for the Jaguar sunday service if anybody wants a nose..

ricola

Original Poster:

468 posts

276 months

Sunday 2nd November 2014
quotequote all
I should have said for those that don't know how the stock suspension is laid out: there is the lateral link and then the anti-roll bar is the only fore-aft location as it goes through a bush in the lateral arm. The extra bushes and the fact a bent spring steel bar is your only link under braking doesn't lead to a particularly well controlled system..

ricola

Original Poster:

468 posts

276 months

Sunday 18th January 2015
quotequote all
Well it's finally time for a new project, if you are seriously interested in having a permanent grin on your face by having this car in your garage PM me!

C. Grimsley

1,364 posts

194 months

Sunday 18th January 2015
quotequote all
I doff my hat to you, lovely bit of retro with some shove.

Carl

5potTurbo

12,482 posts

167 months

Monday 19th January 2015
quotequote all
ricola said:
Well it's finally time for a new project, if you are seriously interested in having a permanent grin on your face by having this car in your garage PM me!
In July 2013 I did say, "if you ever want to sell this...". I'd love to buy it, I really would, but since I posted then we've built another house, so I've a sizeable mortgage now, and I must respond with "Grrrrr, I'll have to pass on this opportunity." frown

ricola

Original Poster:

468 posts

276 months

Thursday 6th August 2015
quotequote all
Well I sold my 996 turbo to get the deposit for a Tesla Model S and that is now my daily. Planning a trip down to the south of france in a couple of weeks in that. Just got back from my third trip over to Spa and luckily somebody had a gopro for a 'parade' lap, enjoy!

https://www.youtube.com/watch?v=fpCeQdOplJE

5potTurbo

12,482 posts

167 months

Friday 7th August 2015
quotequote all
Looked very quick, maybe that was because the others were just so slow? wink

BTW: where did you get your Tesla from? I've a mate who works at Gatwick.

ricola

Original Poster:

468 posts

276 months

Sunday 9th August 2015
quotequote all
I think it was a bit of both, only a parade lap so I was just giving it the odd blast trying not to catch up with the pace car too quickly!

Picked the Tesla up from Birmingham..