Equivalent Part Numbers
Discussion
TooTall Paul said:
Does anybody know what the startermotor is off because mine is screeching, is it possible to change the little cog("bendix"?) on its own? presuming thats all that has worn ??
The starter motor screeching is likely to be the dog clutch refusing to disingange after the engine has started. Unfortunately this will destroy the startermotor in fairly short order. It is however easy to remedy with a good clean up and a bit of grease. However likely the starter motor has to come out to achieve it.
ok ive had the starter out three times now, cleaned it up etc and found one of the brushes stuck in, but still no luck. So i,ve been matching them up to other models and found it is the same as a Nissan Maxima 3.0 inj V6 88 -94 J30 model
Part no ADN 11248. just got to find one in the country now. ill keep you posted
Cheers Paul
Part no ADN 11248. just got to find one in the country now. ill keep you posted
Cheers Paul
TooTall Paul said:
Ok quick update just fitted a nissan maxima starter and it works perfectly just make sure you get the 3.0 inj auto version 88 -94, See how long it lasts now !!!
>> Edited by TooTall Paul on Wednesday 29th June 16:56
Olly, I think you should get this on your table, especially as the man has done the hard grunt and found the right starter motor, fitted it and it works, tried and tested so to speak!
i recently baught a high torque starter from eurolec,who recon they supply tvr direct,
a baring fell out of it in to the clutch, theyve replaced the starter but refused to have anything to do with the rest of the dammage and labour to strip the clutch,and the month its been off the road, any one know what i can do?
a baring fell out of it in to the clutch, theyve replaced the starter but refused to have anything to do with the rest of the dammage and labour to strip the clutch,and the month its been off the road, any one know what i can do?
TooTall Paul said:
Ok quick update just fitted a nissan maxima starter and it works perfectly just make sure you get the 3.0 inj auto version 88 -94, See how long it lasts now !!!
>> Edited by TooTall Paul on Wednesday 29th June 16:56
Thanks for this Paul.
Site updated...
www.tvr-cerbera.fsnet.co.uk/parts.htm (Sorry - been away for a few days & not been checking Pistonheads)
Track rods are from a Ford Scorpio.
Go to www.power-steering.co.uk they will do a full overhaul on Cerbera racks, with warranty, for £115
Go to www.power-steering.co.uk they will do a full overhaul on Cerbera racks, with warranty, for £115
Extra 300 Driver said:
Track rods are from a Ford Scorpio.
Go to www.power-steering.co.uk they will do a full overhaul on Cerbera racks, with warranty, for £115
I was in my local motor factors for a set of track rod ends and they are not the same as ford scorpio!!!! unless they have the wrong ones
Colin
MAGNETIC SWITCH AT THE BOTTOM OF THE DOOR
>> Edited by spartacus on Friday 19th August 21:44
>> Edited by spartacus on Sunday 21st August 20:30
extra 300 driver said:
spartacus said:
Guys, I want to put this on Part Number thread.
So just to confirm I have read this correctly:
The part number is PTC 130/30 (is that original part number?)
RS stock number is 455-3744
This gives you the contact options of NC or NO, cerbera needs NC so discard NO.
brown wire = nc
green = no
white = common
>> Edited by spartacus on Friday 19th August 21:44
>> Edited by spartacus on Sunday 21st August 20:30
Gassing Station | Cerbera | Top of Page | What's New | My Stuff