What's wrong with this?
Discussion
Have a look here...
best get it right then its not side loading.. I have the jig if you want it
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
best get it right then its not side loading.. I have the jig if you want it
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
TVR Beaver said:
Have a look here...
best get it right then its not side loading.. I have the jig if you want it
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
Just read that link, and something Adrian said made me think, thats the side that had the mk2 ARB mount welded on, so maybe is a little warped.best get it right then its not side loading.. I have the jig if you want it
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
thanks for that.
P.S YHM
Edited by Discopotatoes on Wednesday 3rd August 17:47
I seem to remember when I did mine years ago that the top rear wishbones are extremely flexible.
Bolt the whole lot together loosely and then tighten up.
The bottom wishbone is not flexible and stays in the correct position. The hub upright carrier bolts in an upright position and you cannot go wrong with them. You will find that the top wishbone won't easily line up but it does bend and flex.
Bolt the top wishbone to the chassis and you should be able to flex it and bolt it to the hub carrier .
.
Bolt the whole lot together loosely and then tighten up.
The bottom wishbone is not flexible and stays in the correct position. The hub upright carrier bolts in an upright position and you cannot go wrong with them. You will find that the top wishbone won't easily line up but it does bend and flex.
Bolt the top wishbone to the chassis and you should be able to flex it and bolt it to the hub carrier .
.
phazed said:
I seem to remember when I did mine years ago that the top rear wishbones are extremely flexible.
Bolt the whole lot together loosely and then tighten up.
The bottom wishbone is not flexible and stays in the correct position. The hub upright carrier bolts in an upright position and you cannot go wrong with them. You will find that the top wishbone won't easily line up but it does bend and flex.
Bolt the top wishbone to the chassis and you should be able to flex it and bolt it to the hub carrier .
.
That's basically how I did it but getting the top of the upright into the top wish bone was a real struggle, both sides have the same issue by the same amount, I'm wondering if the tops can be bent to fitBolt the whole lot together loosely and then tighten up.
The bottom wishbone is not flexible and stays in the correct position. The hub upright carrier bolts in an upright position and you cannot go wrong with them. You will find that the top wishbone won't easily line up but it does bend and flex.
Bolt the top wishbone to the chassis and you should be able to flex it and bolt it to the hub carrier .
.
Steve_D said:
What position is the toe adjuster in?
Winding it in or out will affect the alignment of that top mount.
Steve
I've tried it in and out and halfway it didn't change the position. The top mount needs to move clockwise about 5mm. All the bolts loose and nothing seems to allow it to sit centrally in the upper wishbone, if it was just one side I'd have thought it maybe bent but both side are exactly the same and nothing I do seems to change anythingWinding it in or out will affect the alignment of that top mount.
Steve
Yes they are handed there are fixings for the hub carriers which have to go in one position.
I've just been out to the garage for a sanity check, if I take out all the thrust washers I can get it to line up but the bottom chassis to wishbone bolts are pushed up tight against the rear most brackets
I've just been out to the garage for a sanity check, if I take out all the thrust washers I can get it to line up but the bottom chassis to wishbone bolts are pushed up tight against the rear most brackets
All bolts are loose and the toe adjuster has been slackened of so the nut is at the end of the thread.
The first photo is the top wishbone equally spaced with the correct washers in place.
The next 2 photo show the bottom wishbone to upright with equal gaps for thrust washers
Then the next two show the toe adjuster and rear bottom mounts, which are pushed right over to the right.
When looking closely at the top wish bone to chassis mounts the piece of tube which holds the bush next to the shock doesn't look 100% straight so this could be my problem. It's weird how both side have the same problem.
The first photo is the top wishbone equally spaced with the correct washers in place.
The next 2 photo show the bottom wishbone to upright with equal gaps for thrust washers
Then the next two show the toe adjuster and rear bottom mounts, which are pushed right over to the right.
When looking closely at the top wish bone to chassis mounts the piece of tube which holds the bush next to the shock doesn't look 100% straight so this could be my problem. It's weird how both side have the same problem.
Edited by Discopotatoes on Friday 2nd December 09:37
Gassing Station | Chimaera | Top of Page | What's New | My Stuff