Pro Street Style MGB GT
Discussion
Thanks tuffer and e600
Nice to know that it is not empty out there!
Anyway I have been playing with the MG pedals and reversed them to put the unit on the floor( - which I did on the original "Super B").
I have also been cutting exhaust bends.......
Nice to know that it is not empty out there!
Anyway I have been playing with the MG pedals and reversed them to put the unit on the floor( - which I did on the original "Super B").
I have also been cutting exhaust bends.......
Edited by Flying Phil on Tuesday 17th November 16:39
By way of a change today I revisited the inlet system. All the manifolds have been smoothed inside and tidied on the outside. Then they were bolted to the heads and the carbs loosely bolted in place. One carb will need shaped, thick, gaskets, as the welding had tilted the stubs.
Then I put the radiator in place and the wings back on.
The next problem area will be the water pump outlet to radiator - the outlet points down and slightly back - and the steering rack is nicely in the way. It would be good if the outlet on three bolts could be rotated 120 degrees - but the three bolts are isosceles not equilateral!!!
Anyway looking at the grille - and the radiator showing underneath it, I thought about the front end treatment - the original "Super B" had a sheet aluminium air dam with small lip. (It now has a fibreglass Sebring style). I thought a more modern approach might be a larger deeper grille - then I remembered I had bought my newer MG grille..........
It is just playing around but I think it may work?
Then I put the radiator in place and the wings back on.
The next problem area will be the water pump outlet to radiator - the outlet points down and slightly back - and the steering rack is nicely in the way. It would be good if the outlet on three bolts could be rotated 120 degrees - but the three bolts are isosceles not equilateral!!!
Anyway looking at the grille - and the radiator showing underneath it, I thought about the front end treatment - the original "Super B" had a sheet aluminium air dam with small lip. (It now has a fibreglass Sebring style). I thought a more modern approach might be a larger deeper grille - then I remembered I had bought my newer MG grille..........
It is just playing around but I think it may work?
Progress - The two front grilles have been swopped and the older - now lower grille, has been split to remove the centre vertical bar with its integral MG shield.
The water outlet casting has been cut and will be re welded with the outlet at a much better angle for the radiator.
I also put a battery to the starter and it only "Clicked" but I'm not sure if there is some sort of inhibitor tied into the automatic transmission??
The water outlet casting has been cut and will be re welded with the outlet at a much better angle for the radiator.
I also put a battery to the starter and it only "Clicked" but I'm not sure if there is some sort of inhibitor tied into the automatic transmission??
I didn't have a chance to have another look at the starter electrics but I have found the gear selector and operating cable. Needless to say that the selector is back at the Diff unless I put a loop in the thick Bowden cable so I will try and get a shorter system sorted - direct from the shifter to the change lever?
Here is a picture of the more fixed front double grille.
Here is a picture of the more fixed front double grille.
Thanks Benters - here is more.....
I spent a bit of time dismantling the gear selector. The gearbox end was just a collet which locked onto a rod end of the cable. The other end was just a simple bearing held in place with a split pin. Then I put the selector cover back on the gear lever - and realised that it fitted the other way round (I had only put it loosely back together after stripping it from the XJ-S). Then it all made sense! The Bowden cable loops back 180 degrees to put the selector back above the gearbox......(Pic to follow).
I spent a bit of time dismantling the gear selector. The gearbox end was just a collet which locked onto a rod end of the cable. The other end was just a simple bearing held in place with a split pin. Then I put the selector cover back on the gear lever - and realised that it fitted the other way round (I had only put it loosely back together after stripping it from the XJ-S). Then it all made sense! The Bowden cable loops back 180 degrees to put the selector back above the gearbox......(Pic to follow).
Gassing Station | MG | Top of Page | What's New | My Stuff