Exhaust bits and more

[Taff_o]

About your exhaust phone [phone] Exhausts UK ask for Matt, a bit of a long shot but they took off a perfectly good stainless steel back piece like you pictured, off my 350i last week if your lucky it may still be there. Good luck.

[Poledriver]

Taff_o said:

About your exhaust phone [phone] Exhausts UK ask for Matt, a bit of a long shot but they took off a perfectly good stainless steel back piece like you pictured, off my 350i last week if your lucky it may still be there. Good luck.

Thanks for that! Unfortunately I ordered a new one on Monday!
Don't suppose you have any spare wheels do you?

[Poledriver]

Ever wished you'd never crawled under the car?







Ho hum, time to find a mobile welder!

[pwd95]

I explained that to you very carefully. I told you it was cracked & needed replacing.

[Poledriver]

pwd95 said:

I explained that to you very carefully. I told you it was cracked & needed replacing.

Yep! You did say it was going, I just wish it had held out till October though. Good job I looked under there now, it does look a bit scary. Shouldn't think it's a particularly major job.

Edited by Poledriver on Wednesday 2nd July 21:34

[pwd95]

Rito guys, here we go....

http://www.pistonheads.com/sales/593422.htm

...I WISH I'D KEPT IT.....

[pwd95]

Can't be arsed to reply on TVRCC too....

[Poledriver]

pwd95 said:

Rito guys, here we go....

http://www.pistonheads.com/sales/593422.htm

...I WISH I'D KEPT IT.....

Have you got another Wedge then Wyn?

[pwd95]

No not yet...

[combine]

Poledriver said:

pwd95 said:

I explained that to you very carefully. I told you it was cracked & needed replacing.

Yep! You did say it was going, I just wish it had held out till October though. Good job I looked under there now, it does look a bit scary. Shouldn't think it's a particularly major job.

Edited by Poledriver on Wednesday 2nd July 21:34

Looks from the pic like the outrigger needs replacing as there's not a lot to weld except rust , presume its the passenger side ? Best to get it done properly or it will break/crack again .

Edited by combine on Wednesday 2nd July 21:56

[mikeb]

Easy fix. Good job it was a removable sill jobbie.

Welding article on the www.tvrwedgepages.co.uk under the maintenance tab if I am not mistaken.

MikeyB

[eesbad]

pwd95 said:

No not yet...

http://www.pistonheads.com/sales/567579.htm

[pwd95]

eesbad said:

pwd95 said:

No not yet...

http://www.pistonheads.com/sales/567579.htm

I've been eyeing this up....

http://www.pistonheads.com/sales/591091.htm

I could take it all apart over the winter & try my hand at engine transplants.

[eesbad]

pwd95 said:

I could take it all apart over the winter & try my hand at engine transplants.

Just asking for a small block Ford, isn't it?

[L33]

Poledriver said:

The exhaust outlet parts numbered 16 and 17 in the picture below.



Any suggestions where I should try?

I have part 16 (both tailpipes) and I think I also have part 17.
There was an issue fitting them to your exhaust due to clearance etc when the engine was replaced which is why there were left off and you have one single (but large) tailpipe sticking out the back.

Here for info on the outrigger repairs:
http://www.tvrwedgepages.co.uk/maint_chassiscoro.h...

Edited by L33 on Thursday 3rd July 09:15

[Poledriver]

Cheers! I ordered the exhaust parts on Monday (silly money!).
I checked the wege pages last night, I'm getting the bits I need today and will get them all jigged up and in place for someone to come round and weld up in next few days!
Bit of any expensive week!! But should be worth it!

[L33]

How about these wheels:
http://cgi.ebay.co.uk/TVR-Oz-Racing-Diamond-Patter...

They have no centre caps but Paul who is selling this wedge:
http://www.pistonheads.com/sales/524441.htm has some for sale in ally that might fit?

[Poledriver]

L33 said:

How about these wheels:
http://cgi.ebay.co.uk/TVR-Oz-Racing-Diamond-Patter...

They have no centre caps but Paul who is selling this wedge:
http://www.pistonheads.com/sales/524441.htm has some for sale in ally that might fit?

Cheers, but I wanted 4 wheels that match. I have bitten the bullet and ordered a new wheel1

Edited by Poledriver on Monday 7th July 12:16

[L33]

Sorry - didn't notice that the ad was only for 2 wheels

[grahamw48]

Pity there weren't four...would have paid good money for a set...like lots of other people I suppose.