Replacing driveshafts
Discussion
I was advidsed at my last service that my driveshafts have quite a bit of play in them and could do with replacement sometime soon. Just had a quick look on clevor trevors website and the CV joints come in at £80 each and uprated raceproved driveshafts £176 each so not a cheap job. To save costs how easy is it to replace these parts for a willing to have a go but not too technically adept Chim owner?
Zippee
£80 is a bit of a rip off for the CV's. Someone led me to this site when I did mine, you're very unlikely to need to change the drive shafts, as it's the bearings that get play in them. Drive shaft's are splined, and if that has gone, then it would just spin in the CV. More likely to snap one than have play in the spline.
You'll need to pack them with Molly grease, and a tip picked up on here was to put the grease into poly bags to weigh out the right amount and then use this to squeeze them in to the CV's.
Make sure the cap head bolts that hold the CV's on to the hub and diff flanges are cleaned out before you try to undo them and that the bit you put in goes down as far as possible, it' easy to shag one and then it's a right pain to get them out . ..
Grotty old job, but not a particularly hard one . .
reasonably priced CV's
£80 is a bit of a rip off for the CV's. Someone led me to this site when I did mine, you're very unlikely to need to change the drive shafts, as it's the bearings that get play in them. Drive shaft's are splined, and if that has gone, then it would just spin in the CV. More likely to snap one than have play in the spline.
You'll need to pack them with Molly grease, and a tip picked up on here was to put the grease into poly bags to weigh out the right amount and then use this to squeeze them in to the CV's.
Make sure the cap head bolts that hold the CV's on to the hub and diff flanges are cleaned out before you try to undo them and that the bit you put in goes down as far as possible, it' easy to shag one and then it's a right pain to get them out . ..
Grotty old job, but not a particularly hard one . .
reasonably priced CV's
Johno said:
You'll need to pack them with Molly grease, and a tip picked up on here was to put the grease into poly bags to weigh out the right amount and then use this to squeeze them in to the CV's.
I thought I was being stupid when I thought of this Johno........then again I always hated getting my hands dirty when I was young. Good man for passing on tips..
I replaced my driveshaft gaiters last year, same amount of work. Here are my tips:
gaiters from www.racetechdirect.co.uk £15 each inc clips
500g moly grease from Halfords about £5
sealey gaiter clip (ear type) tool from www.toolcrew.co.uk £9 inc postage
need a good/new 1/2" drive 8mm hex key & circlip pliers
used one of those pencil wire brushes and a bit of carb cleaner to clean out the CV joint bolts
you have to release the lower wishbone pivot bolts and lift the hub away to get the driveshaft out
torque setting to use on the CV joint bolts is 32-35 lbft, see: www.thegriffithpages.com
although not TVR specific, I thought this info was useful: http://www.rennlist.com/techarticles/944Constant%2...
a fairly straightfoward job if you have the basic tools and all the bits to hand. I spent quite a while cleaning everything and putting POR-15 on any rusty bits while the drive shafts were out, also fitted a set of steve heath drop links at the same time. make sure you've got good solid axle stands! hope that helps, Paul
gaiters from www.racetechdirect.co.uk £15 each inc clips
500g moly grease from Halfords about £5
sealey gaiter clip (ear type) tool from www.toolcrew.co.uk £9 inc postage
need a good/new 1/2" drive 8mm hex key & circlip pliers
used one of those pencil wire brushes and a bit of carb cleaner to clean out the CV joint bolts
you have to release the lower wishbone pivot bolts and lift the hub away to get the driveshaft out
torque setting to use on the CV joint bolts is 32-35 lbft, see: www.thegriffithpages.com
although not TVR specific, I thought this info was useful: http://www.rennlist.com/techarticles/944Constant%2...
a fairly straightfoward job if you have the basic tools and all the bits to hand. I spent quite a while cleaning everything and putting POR-15 on any rusty bits while the drive shafts were out, also fitted a set of steve heath drop links at the same time. make sure you've got good solid axle stands! hope that helps, Paul
Edited by martinipaul on Saturday 5th April 10:22
Johno said:
Zippee
£80 is a bit of a rip off for the CV's. Someone led me to this site when I did mine, you're very unlikely to need to change the drive shafts, as it's the bearings that get play in them. Drive shaft's are splined, and if that has gone, then it would just spin in the CV. More likely to snap one than have play in the spline.
You'll need to pack them with Molly grease, and a tip picked up on here was to put the grease into poly bags to weigh out the right amount and then use this to squeeze them in to the CV's.
Make sure the cap head bolts that hold the CV's on to the hub and diff flanges are cleaned out before you try to undo them and that the bit you put in goes down as far as possible, it' easy to shag one and then it's a right pain to get them out . ..
Grotty old job, but not a particularly hard one . .
reasonably priced CV's
Johno£80 is a bit of a rip off for the CV's. Someone led me to this site when I did mine, you're very unlikely to need to change the drive shafts, as it's the bearings that get play in them. Drive shaft's are splined, and if that has gone, then it would just spin in the CV. More likely to snap one than have play in the spline.
You'll need to pack them with Molly grease, and a tip picked up on here was to put the grease into poly bags to weigh out the right amount and then use this to squeeze them in to the CV's.
Make sure the cap head bolts that hold the CV's on to the hub and diff flanges are cleaned out before you try to undo them and that the bit you put in goes down as far as possible, it' easy to shag one and then it's a right pain to get them out . ..
Grotty old job, but not a particularly hard one . .
reasonably priced CV's
Did you buy the gaiters from Prolinx ?, I reckon that extra length they describe would make them last longer, any thoughts?
martinipaul said:
I replaced my driveshaft gaiters last year, same amount of work. Here are my tips:
gaiters from www.racetechdirect.co.uk £15 each inc clips
500g moly grease from Halfords about £5
sealey gaiter clip (ear type) tool from www.toolcrew.co.uk £9 inc postage
need a good/new 1/2" drive 8mm hex key & circlip pliers
used one of those pencil wire brushes and a bit of carb cleaner to clean out the CV joint bolts
you have to release the lower wishbone pivot bolts and lift the hub away to get the driveshaft out
torque setting to use on the CV joint bolts is 32-35 lbft, see: www.thegriffithpages.com
although not TVR specific, I thought this info was useful: http://www.rennlist.com/techarticles/944Constant%2...
a fairly straightfoward job if you have the basic tools and all the bits to hand. I spent quite a while cleaning everything and putting POR-15 on any rusty bits while the drive shafts were out, also fitted a set of steve heath drop links at the same time. make sure you've got good solid axle stands! hope that helps, Paul
martinipaulgaiters from www.racetechdirect.co.uk £15 each inc clips
500g moly grease from Halfords about £5
sealey gaiter clip (ear type) tool from www.toolcrew.co.uk £9 inc postage
need a good/new 1/2" drive 8mm hex key & circlip pliers
used one of those pencil wire brushes and a bit of carb cleaner to clean out the CV joint bolts
you have to release the lower wishbone pivot bolts and lift the hub away to get the driveshaft out
torque setting to use on the CV joint bolts is 32-35 lbft, see: www.thegriffithpages.com
although not TVR specific, I thought this info was useful: http://www.rennlist.com/techarticles/944Constant%2...
a fairly straightfoward job if you have the basic tools and all the bits to hand. I spent quite a while cleaning everything and putting POR-15 on any rusty bits while the drive shafts were out, also fitted a set of steve heath drop links at the same time. make sure you've got good solid axle stands! hope that helps, Paul
Edited by martinipaul on Saturday 5th April 10:22
I need to replace both gaiters on the both shafts !!, am I right in assuming i could disconnect at the diff and slide inboard joint off the splines and not have to take off/break down the wheel hubs to do the outboards?
Also cant locate the gaiter clip tool you bought could you be more specific please mate?
Brgds
Ian
I also need to replace my CV joint and am a bit confused about the replacement parts after reading all the PH threads on this.
Johno are you sure the prolinx ones will fit? It says 28 splines whereas the original Granada replacement are 25? Also a thread mentioned the Griff/Chimeara ones are different (Ford Siera Cosworth first model). One can only remanufacture the old ones for the Cosworth ones in Holland! Granada ones (GKN/Spidan/Lobro) are available.
Thanks,
Peter
Johno are you sure the prolinx ones will fit? It says 28 splines whereas the original Granada replacement are 25? Also a thread mentioned the Griff/Chimeara ones are different (Ford Siera Cosworth first model). One can only remanufacture the old ones for the Cosworth ones in Holland! Granada ones (GKN/Spidan/Lobro) are available.
Thanks,
Peter
Peter66 said:
I also need to replace my CV joint and am a bit confused about the replacement parts after reading all the PH threads on this.
Johno are you sure the prolinx ones will fit? It says 28 splines whereas the original Granada replacement are 25? Also a thread mentioned the Griff/Chimeara ones are different (Ford Siera Cosworth first model). One can only remanufacture the old ones for the Cosworth ones in Holland! Granada ones (GKN/Spidan/Lobro) are available.
Thanks,
Peter
If they don't fit I'm not quite sure how I've managed the last 5k miles since I changed all 4. Johno are you sure the prolinx ones will fit? It says 28 splines whereas the original Granada replacement are 25? Also a thread mentioned the Griff/Chimeara ones are different (Ford Siera Cosworth first model). One can only remanufacture the old ones for the Cosworth ones in Holland! Granada ones (GKN/Spidan/Lobro) are available.
Thanks,
Peter
Perhaps I'm just lucky

They fit my car and every other Griffith/Chimaera owner I've referred there . .
Good luck.
vee5 said:
Has anyone tried the type of replacement gaitor that is supplied split so you can fit it and glue it back together without having to dissasemble whole caboodle?
The lazy side of me is interested but the "biiter experience" half suspects this may not be a quality solution?
Good enough to get through an MOT. but from what I have heard they don't last to long.The lazy side of me is interested but the "biiter experience" half suspects this may not be a quality solution?
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



. Just got back myself, but sorry no help to you on this.

te,please dont contaminate these cars with inferior crap parts.