Am I alone ? Monaro Wipers.
Discussion
Spotted some marking on the plastic trim below my screen around the driver's side wiper drive shaft, anyone else spotted this wear happening on their car ? Has it been discussed previously with solutions suggested, the trim looks to be in the right place, but it's obvious there's not enough clearance between the wiper arm and the trim.
)ARAF said:
The problem wit that, is that the arms are usually on tapered splines.
I will have a look at spacing the pivot assembly away from the body of the car, assuming the wiper motor is on the other arm, as you rightly say Araf, no point in trying to move the arm on the shaft. Would still be interested to see if anyone else has the same clearance issue.ARAF said:
How about a bigger nylon washer under the arm (between arm and scuttle cover)? That would space the scuttle cover away from the arm.
Another option to look at, cheers, and maybe the same solution as suggested by JohnM, will have the spanners out tomorrow night and take a closer look.
LS2Noir said:
THUNDER STORM said:
Are you sure that the plastic cover itself as not come loose and lifted allowing arm to rub.
Ade
Got in from work, went out to car to have a closer look at the Scuttle Panel and the heaven's opened ! Ade
Will have a closer look tomorrow, weather permitting.
Ade
THUNDER STORM said:
Have you checked this yet?
Ade
Had a closer look, and as you can see below, the red arrow shows where there is an amount of clearance between the 2 sections of the Scuttle Panel that does not look correct, not sure if they come out of the factory like that, possibly the plastic has changed shape over time. I will be looking at how I can get the 2 sections to meet correctly without the clearance, if I can do this then it may give clearance between the wiper arm and plastic panel. Will update the post with any progress.Ade
LS2Noir said:
THUNDER STORM said:
Have you checked this yet?
Ade
Had a closer look, and as you can see below, the red arrow shows where there is an amount of clearance between the 2 sections of the Scuttle Panel that does not look correct, not sure if they come out of the factory like that, possibly the plastic has changed shape over time. I will be looking at how I can get the 2 sections to meet correctly without the clearance, if I can do this then it may give clearance between the wiper arm and plastic panel. Will update the post with any progress.Ade
Ade
With a little work with a hairdryer and a new plastic rivet I think I have solved the issue.
No gap between the upper and lower sections of the Scuttle Panel.
Can now see clearance between the Wiper Arm and plastic panel.
Hopefully things will stay where they are, and efforts were worthwhile.
No gap between the upper and lower sections of the Scuttle Panel.
Can now see clearance between the Wiper Arm and plastic panel.
Hopefully things will stay where they are, and efforts were worthwhile.
LS2Noir said:
With a little work with a hairdryer and a new plastic rivet I think I have solved the issue.
No gap between the upper and lower sections of the Scuttle Panel.
Can now see clearance between the Wiper Arm and plastic panel.
Hopefully things will stay where they are, and efforts were worthwhile.
Nice one, thought it must be the plastic and not the arm.No gap between the upper and lower sections of the Scuttle Panel.
Can now see clearance between the Wiper Arm and plastic panel.
Hopefully things will stay where they are, and efforts were worthwhile.
Glad its sorted.
Ade
jelevents said:
Thanks for the heads up Nick, checked mine and exactly the same, time to get busy with the hair dryer.
Hope you get on OK with sorting the issue, if you need any help/suggestions alone the way give me a shout, if you decide to use a new plastic rivet as I have done, be careful where you drill the hole as there is a cut-out section in the lower section of the Scuttle Panel which leaves very little plastic to aim for.Good Luck
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff