Moving my Can-Am

Moving my Can-Am

Author
Discussion

UltimaCH

Original Poster:

3,155 posts

188 months

Monday 24th November 2014
quotequote all
I will be leaving Locarno and my home in the coming months. The Ultima is following also.

A question to fellow owners and builders. As the Can-Am is currently on its dolly, it has wheels but no tyres, so that excludes wheeling the rolling chassis around.

I was thinking of moving the lot in one go, dolly included, but it needs to be transported in a big van or small lorry with a hoist to lift and lift off the vehicle. As the body pre-fit has not yet been done (I'm doing it myself), I was thinking of mounting loosely all the bodywork onto the chassis to facilitate the transport and reduce possible damages

Is this feasible or need I look into other ways of doing things?



Edited by UltimaCH on Monday 24th November 13:40

deadscoob

2,263 posts

259 months

Monday 24th November 2014
quotequote all
Why not just buy some tyres do you can roll it onto a trailer?

UltimaFAN

107 posts

128 months

Monday 24th November 2014
quotequote all
if you can find another set of smaller wheels which fits, it can be enough for rolling a 4-500kg chassis.

Where are you moving?

UltimaCH

Original Poster:

3,155 posts

188 months

Monday 24th November 2014
quotequote all
UltimaFAN said:
if you can find another set of smaller wheels which fits, it can be enough for rolling a 4-500kg chassis.

Where are you moving?
We are moving to Uvrier (VS). The workshop and garage is big and sufficient for all my machinery. We will be able to exchange progress reports with less distance to travel.

UltimaCH

Original Poster:

3,155 posts

188 months

Monday 24th November 2014
quotequote all
deadscoob said:
Why not just buy some tyres do you can roll it onto a trailer?
Its a bit early to get tyres as the build will continue for some time more. Tyres may be too old to be used when the vehicle will be ready.

deadscoob

2,263 posts

259 months

Monday 24th November 2014
quotequote all
Try and buy a 2nd hand set, that's what I did smile

UltimaCH

Original Poster:

3,155 posts

188 months

Monday 24th November 2014
quotequote all
That's an idea, but I have to consider the hassle of getting them over to Switzerland. I'll try with my local tyre dealer to see if he has some old rubber hanging around....

Storer

5,024 posts

214 months

Monday 24th November 2014
quotequote all
You could use wood (don't laugh).

Just get a sheet of 20mm ply wood and cut in half and glue the two halves together. Then cut out 4 circles, drill centre and bolt holes and you have a set of wheels you can move the chassis on.

They never get a puncture too...

Cheap way to roll your car safely around.



Paul

UltimaCH

Original Poster:

3,155 posts

188 months

Monday 24th November 2014
quotequote all
Paul that's brillant. Great idea!

Storer

5,024 posts

214 months

Monday 24th November 2014
quotequote all
I try to please.


Paul

Steve_D

13,737 posts

257 months

Tuesday 25th November 2014
quotequote all
Sorry, I should have proposed the wooden wheels.
Made a set for a caravan so I could lower it and store in my garage.

Steve

3Dee

3,206 posts

220 months

Tuesday 25th November 2014
quotequote all
Hi Dan,

Area looks spectacular - gad I wish I was there!
Any reason for the move? ...or was it all to do with bigger workshop? wink Jeez, how did you manage to get THAT past the boss? cool

I also concur with Steve and storer.. I used 'wooden wheels' as well! In fact in my case, the factory kindly sent them down to me!

I am looking forward (not) to an op on my knee in a couple of weeks.. apparently my mis-spent youf has caught up with me (contact sports almost guarantee joint probs i8n later years - if only I had known ...or listened to my betters!) , so will be hopping around on crutches over xmas!

Good luck... we keep threatening it, but maybe we will finally meet some day!

Keith

Merry xmas everyone! Bah-HUMBUG!

UltimaCH

Original Poster:

3,155 posts

188 months

Tuesday 25th November 2014
quotequote all
3Dee said:
Hi Dan,

Area looks spectacular - gad I wish I was there!
Any reason for the move? ...or was it all to do with bigger workshop? wink Jeez, how did you manage to get THAT past the boss? cool

I also concur with Steve and storer.. I used 'wooden wheels' as well! In fact in my case, the factory kindly sent them down to me!

I am looking forward (not) to an op on my knee in a couple of weeks.. apparently my mis-spent youf has caught up with me (contact sports almost guarantee joint probs i8n later years - if only I had known ...or listened to my betters!) , so will be hopping around on crutches over xmas!

Good luck... we keep threatening it, but maybe we will finally meet some day!

Keith

Merry xmas everyone! Bah-HUMBUG!
Yes Keith, the area is great with dry, sunny, warm weather and little overall rain, so much more enjoyable than south of the Alps. Local food and wines are great and people enjoy living. Locarno remains within easy reach, so a quick pop down for a meal and meet up with friends remains something which can be done with a couple of hours to spend. There is an airport close by in Sion. Don't know what flights exist in or out, but the military are moving out and commercial flights should be developed. Also for those into winter sports, there's plenty to do with just 1/2h driving to get there. Unfortunately I also have a "wobbly" knee, so skiing is out since a number of years now weeping

The decision to move was jointly taken with Madame as she wants to remain closer to family and I with other Ultima builders too. I also concur as I will be back in a french speaking area. smile and things will be cheaper for us, so finishing the Can-Am remains in the books. Guess it's a win win situation overall.


Edited by UltimaCH on Tuesday 25th November 10:36

UltimaCH

Original Poster:

3,155 posts

188 months

Wednesday 26th November 2014
quotequote all
Storer said:
You could use wood (don't laugh).

Just get a sheet of 20mm ply wood and cut in half and glue the two halves together. Then cut out 4 circles, drill centre and bolt holes and you have a set of wheels you can move the chassis on.

They never get a puncture too...

Cheap way to roll your car safely around.



Paul
Paul and others having used the wooden "chariot" wheels, what size diameter is recommended? I guess the diameter needs to be sufficient to enable the chassis to be above the ground level.

Storer

5,024 posts

214 months

Wednesday 26th November 2014
quotequote all
If you make them too small they will make it harder to push and may 'skid' rather than roll.

600mm diameter is good and you will get all 4 out of a 2400x1200 sheet of ply.



Paul

UltimaCH

Original Poster:

3,155 posts

188 months

Wednesday 26th November 2014
quotequote all
Thanks mate.

UltimaFAN

107 posts

128 months

Wednesday 26th November 2014
quotequote all
Don t forget to post a picture of your new "rolling chassis" when the wheels are done!

You talked about other builderS in the area, did I miss something?

I ´m looking forward doing some nice drive, black and white, in the mountains in the region! We should set 2016 as the objective. I have been already invited to do the Grand-Saint-Bernard pass opening in Mai 2015, it might be more 2016 now, but two Ultimas would be great.

UltimaCH

Original Poster:

3,155 posts

188 months

Wednesday 26th November 2014
quotequote all
UltimaFAN said:
Don t forget to post a picture of your new "rolling chassis" when the wheels are done!

You talked about other builderS in the area, did I miss something?

I ´m looking forward doing some nice drive, black and white, in the mountains in the region! We should set 2016 as the objective. I have been already invited to do the Grand-Saint-Bernard pass opening in Mai 2015, it might be more 2016 now, but two Ultimas would be great.
I sure will post some pictures of the Can-Am with it's "chariot" wheels. That should get plenty of giggles going.

True, I should have said builder as I haven't heard of anyone else in the region, not unless someone pops out of the woods. Who knows, as it seems Ultima owners are sometimes very hush hush people until you get to know them.

I would love to do some black and white drives. That would certainly open plenty of eyes here I imagine... biggrin

UltimaCH

Original Poster:

3,155 posts

188 months

Friday 28th November 2014
quotequote all
After Paul's suggestion of making a set of wooden wheels, I had a closer look yesterday at the hubs and callipers. I can't figure out how to get some "chariot" wheels to clear the brake callipers without either removing them temporarily, or cut the inner side of the wheel without removing too much structural strength. Any recommendations?




Steve_D

13,737 posts

257 months

Friday 28th November 2014
quotequote all
You just need a plywood wheel spacer so your wheel now becomes three thickness's of ply just at the centre.

Steve