S2 Long pedal travel
Discussion
Hi,
I had long felt that my brakes were not quite as sharp as expected so recently fitted new stainless braided hoses, front pads and had the front callipers refurbished.
I have since driven approx 500 miles and bled the brakes several times (most recent getting the pros to do it), however the pedal still does n't feel right. Key facts are these:
1) The pedal can be pressed about 25mm (engine not running) before resistance is felt.
2) If I start the engine with the pedal pressed it drops a little.
3) When driving if I go to brake the pedal seems to have a small amount of resistance fairly quickly but this small amount of resistance seems to continue until the pedal is quite a way down before deceleration is significant.
4) If I pump the pedal with the engine running I get a hard peddle and it does n't go down further under firm pressure (I compared my definition of firm by doing the same in my 2003 Passat).
5) When the engine is off if I push the pedal slowly a couple of times the point of maximum resistance increases (i.e. the pedal gets higher).
6) I have noticed that the rubber hoses going between the remote reservoir and the master cylinder look like they are getting condensation on them after the car has been stood for a couple of days. This feels oily. No other hoses in the engine bay get this condensation.
7) If I jam the brakes on hard then I can lock the wheels and the car pulls up in a straight line.
8) I can't see any obvious fluid leaks from any of the joins in the hydraulic system.
I have read that air can get into the system without any fluid getting out. Based on this I'm thinking that I either have:
1) A slow air leak
2) The hoses between the reservoir and master cylinder have gone porous and are letting water/air into the fluid.
3) Master cylinder seals shot
I favour 2 as a theory but have never heard of this before...what do others think? am I missing something?
Thanks,
Ralph
I had long felt that my brakes were not quite as sharp as expected so recently fitted new stainless braided hoses, front pads and had the front callipers refurbished.
I have since driven approx 500 miles and bled the brakes several times (most recent getting the pros to do it), however the pedal still does n't feel right. Key facts are these:
1) The pedal can be pressed about 25mm (engine not running) before resistance is felt.
2) If I start the engine with the pedal pressed it drops a little.
3) When driving if I go to brake the pedal seems to have a small amount of resistance fairly quickly but this small amount of resistance seems to continue until the pedal is quite a way down before deceleration is significant.
4) If I pump the pedal with the engine running I get a hard peddle and it does n't go down further under firm pressure (I compared my definition of firm by doing the same in my 2003 Passat).
5) When the engine is off if I push the pedal slowly a couple of times the point of maximum resistance increases (i.e. the pedal gets higher).
6) I have noticed that the rubber hoses going between the remote reservoir and the master cylinder look like they are getting condensation on them after the car has been stood for a couple of days. This feels oily. No other hoses in the engine bay get this condensation.
7) If I jam the brakes on hard then I can lock the wheels and the car pulls up in a straight line.
8) I can't see any obvious fluid leaks from any of the joins in the hydraulic system.
I have read that air can get into the system without any fluid getting out. Based on this I'm thinking that I either have:
1) A slow air leak
2) The hoses between the reservoir and master cylinder have gone porous and are letting water/air into the fluid.
3) Master cylinder seals shot
I favour 2 as a theory but have never heard of this before...what do others think? am I missing something?
Thanks,
Ralph
Thanks for all the advice.
I've been able to investigate a bit further today and I can confirm that there is no improvement in the pedal whether the handbrake is off or on. I did the rear brakes (wheel cylinders + stainless hoses) about five years ago. Since then I've had no braking issues until now...
I've checked all the hose connections front and rear. There was no visual indication of fluid leaking out anywhere. The two pipe connections out of the master cylinder that are furthest from the servo felt a bit looser than I'd like so I nipped them up. I then wiped round the connections where the hoses go into the front callipers and thought there might have been a trace of liquid on the kitchen roll but then again maybe there was n't...
Feeling despondent I bleed the front brakes,hoping that the trace of liquid may lead to some air coming out, but the fluid was clear. As a last resort I then bled the rear (yes, I know wrong sequence), offside = no bubbles - nearside (after a while) loads of them. Pedal now feels much better but I am left with the worry that there may be a slow leak somewhere.
I have yet to split the master cylinder from the servo - maybe a job for tomorrow. In the meantime if anyone has any further thoughts I'd be keen to hear them.
Ralph
I've been able to investigate a bit further today and I can confirm that there is no improvement in the pedal whether the handbrake is off or on. I did the rear brakes (wheel cylinders + stainless hoses) about five years ago. Since then I've had no braking issues until now...
I've checked all the hose connections front and rear. There was no visual indication of fluid leaking out anywhere. The two pipe connections out of the master cylinder that are furthest from the servo felt a bit looser than I'd like so I nipped them up. I then wiped round the connections where the hoses go into the front callipers and thought there might have been a trace of liquid on the kitchen roll but then again maybe there was n't...
Feeling despondent I bleed the front brakes,hoping that the trace of liquid may lead to some air coming out, but the fluid was clear. As a last resort I then bled the rear (yes, I know wrong sequence), offside = no bubbles - nearside (after a while) loads of them. Pedal now feels much better but I am left with the worry that there may be a slow leak somewhere.
I have yet to split the master cylinder from the servo - maybe a job for tomorrow. In the meantime if anyone has any further thoughts I'd be keen to hear them.
Ralph
Philpot - where did your "I told you so" post go? 
The brake hoses were made up for me by well known companies. The car has done about 7500miles since I did the rear wheel cylinders and is always garaged, although I do drive it in the wet on occasion.
I'll have another play tonight and hopefully get the car over to Neil Garners tomorrow so they can feel the pedal and hopefully give me a pro opinion on whether the master cylinder is good or not.
The brake hoses were made up for me by well known companies. The car has done about 7500miles since I did the rear wheel cylinders and is always garaged, although I do drive it in the wet on occasion.
I'll have another play tonight and hopefully get the car over to Neil Garners tomorrow so they can feel the pedal and hopefully give me a pro opinion on whether the master cylinder is good or not.
You don't attain idol status for correct problem diagnosis though! - that goes to greymrj 
I just pulled back the dust boots on the rear wheel cylinders and brake fluid started dripping out. I checked the invoice and I only fitted the last set in 2009.
Thanks to all for the advice. I'm hopeful that I can now sort this out.
I just pulled back the dust boots on the rear wheel cylinders and brake fluid started dripping out. I checked the invoice and I only fitted the last set in 2009.
Thanks to all for the advice. I'm hopeful that I can now sort this out.
Gassing Station | S Series | Top of Page | What's New | My Stuff