Cambelt fun on a 1993 Celica....
Discussion
Anyone out there changed one of these? I have a 93 Celica GT as the age of belt is unknown I decided to take the plunge and change it. Anyway so far I have got the top cover off and discovered the belt area is covered in engine oil (which isnt ideal) and the bottom pulley bolt wont come off.
Does anyone know if the pulley bolt turns clockwise or anti? And also what seal is likely to be responsible for leaking oil into the the cam covers?
Does anyone know if the pulley bolt turns clockwise or anti? And also what seal is likely to be responsible for leaking oil into the the cam covers?
Thanks PK500, jamming the flywheel should be fairly obvious, clearly I am not thinking that straight today!
Anyway, I have made progress of sorts, picked up an electric impact gun from my younger brother which I might use in place of my breaker bar and bought a pulley puller as I needed one.
A couple of bad camera phone pictures just to cheer the thread up, my alfresco workshop....
And the thing that bothers me oil all over the belt and tensioners...
Anyway, I have made progress of sorts, picked up an electric impact gun from my younger brother which I might use in place of my breaker bar and bought a pulley puller as I needed one.
A couple of bad camera phone pictures just to cheer the thread up, my alfresco workshop....
And the thing that bothers me oil all over the belt and tensioners...
Update, the amazing electric impact gun, vibrates, makes lots of noise but it seems to either be broken or have a fail safe clutch and wont turn the nut....Deep joy! Also I have finally got the starter motor off (with a view to jamming the flywheel). Cant figure out a safe way to do this without possibly breaking teeth!
Will have to crack out the big breaker bar and try, try again....Sometimes I enjoy working on cars, this isn't one of them!
Will have to crack out the big breaker bar and try, try again....Sometimes I enjoy working on cars, this isn't one of them!
Update, update, just applied the totally unrecommended Red neck method... Put the starter back in, reconnect the alternator, disconnect the ignition. Then fit a socket and breaker bar, wedge it safely ish in position, move all possible damageable items and declared "watch this!".
I turned the ignition on flicked the starter and Gudunk, wrrrr!!!! I climbed gingerly out of the drivers seat crept under the car and joy of joys the bolts was loose! Now to get on with it...
The bad youtube video which inspired this stupidity....
http://www.youtube.com/watch?v=2Zu5g95gpqo
I turned the ignition on flicked the starter and Gudunk, wrrrr!!!! I climbed gingerly out of the drivers seat crept under the car and joy of joys the bolts was loose! Now to get on with it...
The bad youtube video which inspired this stupidity....
http://www.youtube.com/watch?v=2Zu5g95gpqo
Big girl? Harsh but probably fair! Anywho I have most of it back together, ran out of time to complete it and other commitments mean that I wont get to work on the car till the middle of next week, hopefully the belt is on correctly!
A couple of thoughts, I don't recall using any of my trusty 13mm sockets on the car at all, is this a common Japanese thing to only use even numbered bolts?! My 14 and 12mm sockets had gone almost unused until this car came along (I had almost got to the poniut of binning them!). Secondly the little pin cam tensioner thing, who on earth dreamt that up? They need a slap!
A couple of thoughts, I don't recall using any of my trusty 13mm sockets on the car at all, is this a common Japanese thing to only use even numbered bolts?! My 14 and 12mm sockets had gone almost unused until this car came along (I had almost got to the poniut of binning them!). Secondly the little pin cam tensioner thing, who on earth dreamt that up? They need a slap!
Mr2Mike said:
The hydraulic tensioner that you have to compress and hold in place with an allen key or drill bit? They are a bit fiddly, but OTOH it means you don't have any worries about setting up the belt tension correctly.
Yes that's the beasty, when you put it that way I can see the point! Finally a bit of an update, initially I thought all was well, car started fine, ran up the road, felt good etc etc. Then I got to some traffic lights and the engine dipped down to idle, except it didn't it just stalled.
I re started it but found I had no tickover, now this puzzled me. I got the car home and checked it over sure enough, it would rev but it would not idle.
I figured this was either a secondary problem or I had cocked up the timing.
I did a bit of googling found a procedure to deal with poor tick over (clean out part of the throttle) so I did that, re tried, still wouldn't tick over once warm, so re set the timing using a different method.
Re started the car and found that the different (proper method didn't work at all and the car ran like a bag of spanners. At this point I threw my tools around in disgust and called it quits!
Today I took the belt off again and found all my original markings and re set it as accurately as I could and fired it up. It ran fine to start with, ticked over (cold) and reved up okay but once warmed started to miss and needed throttle to pick the revs up. Any bright ideas?
I re started it but found I had no tickover, now this puzzled me. I got the car home and checked it over sure enough, it would rev but it would not idle.
I figured this was either a secondary problem or I had cocked up the timing.
I did a bit of googling found a procedure to deal with poor tick over (clean out part of the throttle) so I did that, re tried, still wouldn't tick over once warm, so re set the timing using a different method.
Re started the car and found that the different (proper method didn't work at all and the car ran like a bag of spanners. At this point I threw my tools around in disgust and called it quits!
Today I took the belt off again and found all my original markings and re set it as accurately as I could and fired it up. It ran fine to start with, ticked over (cold) and reved up okay but once warmed started to miss and needed throttle to pick the revs up. Any bright ideas?
Gassing Station | Home Mechanics | Top of Page | What's New | My Stuff