Squealing Fan Belt, but why.....
Discussion
VladD said:
tyre_tread said:
Loose 'fan' belt i.e. alternator drive belt.
Slips on start up due to damp and then again when under load.
Why would it slip under load?Slips on start up due to damp and then again when under load.
it'll be either
loose
knackered belt
worn pulley
dirty pulleys - i used to have a car that put a drip of PS fuild on the pulley, had to clean it once a week to prevent slip.
VladD said:
No, freshly tightened.
New belt and tightened or just tightened? Have you also checked the levels of the battery as sometimes if the fluids are a bit low and of course after starting (several amps) this would course a massive electrical drain as it attempts to recharge a dead/low battery.
On full beam does it give a constant light or fluctuates with acceleration?
And it appears now they are called auxiliary drive belts
as I found out when I replaced the one on the Scenic.Edited by Morningside on Tuesday 1st January 19:07
Could be any of the above - extra load on alternator causing more "drag" so if belt or pulley is worn, or not tight enough, it'll squeal under load, especially if the belt and/or pulley is wet. Dust a little talc on it and see if it stops.
One other possibility is that the alternator bearings need lubrication, causing drag, and the extra electrical load is jut enough to make the belt squeal. The "talc trick" won't help that - but at least you'll know what the problem is!
One other possibility is that the alternator bearings need lubrication, causing drag, and the extra electrical load is jut enough to make the belt squeal. The "talc trick" won't help that - but at least you'll know what the problem is!
Is it a V belt or a Poly V belt?
As a single V belt wears it effectively becomes narrower and fits further into the V of the pulley
At a certain point the belt will be so thin that when you tighten it. it no longer grips on the sides against the V of the pulley and its only point of contact is the very bottom surface against the pulley
that is usually not enough surface to grip anaginst so the belt slips and skreeches under load.
Fit a new belt OMHO.
As a single V belt wears it effectively becomes narrower and fits further into the V of the pulley
At a certain point the belt will be so thin that when you tighten it. it no longer grips on the sides against the V of the pulley and its only point of contact is the very bottom surface against the pulley
that is usually not enough surface to grip anaginst so the belt slips and skreeches under load.
Fit a new belt OMHO.
It's probably just grease (or soap, or talc, or whatever else has been put on in the past to stop it squeaking) making it slip. Wipe the outside of the pulleys and the inside of the belt clean as far as you reasonably can, then spray belt dressing spray on the belt. This will stop it slipping and making noises.
(Other home remedies such as soap, talc etc might stop it squealing but usually don't stop it slipping.)
(Other home remedies such as soap, talc etc might stop it squealing but usually don't stop it slipping.)
GreenV8S said:
It's probably just grease (or soap, or talc, or whatever else has been put on in the past to stop it squeaking) making it slip. Wipe the outside of the pulleys and the inside of the belt clean as far as you reasonably can, then spray belt dressing spray on the belt. This will stop it slipping and making noises.
(Other home remedies such as soap, talc etc might stop it squealing but usually don't stop it slipping.)
Who in their right mind would use soap? Talc does make it grip though. Think about rock climbers using chalk dust. It's not so they don't squeak as they loose their grip on the cliff face.(Other home remedies such as soap, talc etc might stop it squealing but usually don't stop it slipping.)
Obvioulsy what you said would be the proper solution but talc smells much nicer.
VladD said:
Thanks for all of the replies. It looks as though the battery may be suspect. We'll get that replaced and see if it solves the problem. Who need Wiki when you've got PH. 
yup that'd make sense as all the leccy load would be taken up by the alt so its doing more work than normal.
id still change the belt if its slipped much though, they wear out a lot quicker when slipping.
Edited by Hooli on Wednesday 2nd January 17:17
Gassing Station | General Gassing [Archive] | Top of Page | What's New | My Stuff



