S1 Replacement Hood

S1 Replacement Hood

Author
Discussion

LoFlyer

Original Poster:

48 posts

37 months

Sunday 25th August
quotequote all
I've purchased a new Cabrio replacement hood for my TVR S1 (1988). I also had the top bar reupholstered because it was cut up in multiple places near the hinge bolts. Unfortunately they covered over the bolt holes in the bar for the collapsible roof stays that hold it in place and I can't find them. I thought this would be easy but everything seems solid underneath ???? I really don't want to screw up an expensive upholstering job by cutting holes in the wrong place.Can anyone provide distance from the center of the bar along with distance from the front or rear for your roof stay attachment points?

phillpot

17,249 posts

189 months

Sunday 25th August
quotequote all

My hood stays go onto two studs set into the fibreglass of the targa hoop, they are 805mm between centres. If the trimmer has put a thin layer of sponge under the leathercloth they will be difficult to feel the holes for your bolts. Once you think you're close, poking with a fine needle might find them?

But, of course, as the old saying goes "no two are the same", don't think the budget ran to a tape measure at TVR !!!



Edited by phillpot on Sunday 25th August 21:22

GreenV8S

30,416 posts

290 months

Sunday 25th August
quotequote all
I assume you saw the bits before it was sent away. Does it definitely have a female thread there and not studs?

If they're steel, you should be able to get a reasonably accurate location with a metal detector. I've never cut up a hoop but I assume there's no other metal in there apart from the fixings. The fore and aft position will be fixed by the position of the hoop and the length of the struts, so you should be able to judge that reasonably accurately.

LoFlyer

Original Poster:

48 posts

37 months

Sunday 25th August
quotequote all
Great replies. Thanks. I definitely have female threads in the hoop. I'll do some measurements and mark the spots. Somewhere I have a magnetic stud finder. I'll try that before I do any cutting. You're right, they could have filled the threaded holes with foam. I'll let you know how it comes out.

GreenV8S

30,416 posts

290 months

Monday 26th August
quotequote all
If the stud finder doesn't work, I'd try probing with a pin to see of you can find the metal nut. If you puh the pin in until you hit the hoop and tap on the end, it should be obvious whether you found fibreglass or metal.

phillpot

17,249 posts

189 months

Monday 26th August
quotequote all

the threaded bobbins (inserts) TVR used are brass, magnet isn't going to work wink


Electronic stud finders can detect copper pipes and wires so should pick up brass?





Edited by phillpot on Monday 26th August 08:10

LoFlyer

Original Poster:

48 posts

37 months

Monday 26th August
quotequote all
I tried the magnet. No luck, therefore, as you pointed out, it's brass. I'll use the measurements provided to get close and then start probing with a needle. Note to self: Take photos of everything. Measure everything. It's a TVR. Never assume anything!

LoFlyer

Original Poster:

48 posts

37 months

Sunday 1st September
quotequote all
It took awhile, but I found the threaded brass inserts in the targa hoop and installed the roof stays. Thank you for your assistance. Unfortunately I now have another problem. The fabric hood is not taut when the stays are extended. Looks like a long talk with the upholstery guy and some major alterations to the sides.

LoFlyer

Original Poster:

48 posts

37 months

Sunday 1st September
quotequote all

Astacus

3,475 posts

240 months

Monday 23rd September
quotequote all
Yes I wouldn’t be happy with that at all

LoFlyer

Original Poster:

48 posts

37 months

Monday 23rd September
quotequote all
I called the fitter and explained the situation. We chose a hot day to soften the fabric and vinyl window. I drove the car to the shop. It took three hours and two pairs of very strong hands but the results were very good. And no charge! Now I have to install the weather stripping. Thanks for all the assistance.

magpies

5,142 posts

188 months

Tuesday 24th September
quotequote all
Which way did you push/pull/stretch the fabric /window?

Mine is very similar.

LoFlyer

Original Poster:

48 posts

37 months

Wednesday 25th September
quotequote all
It required tightening in multiple directions. To find out what I was dealing with I had to carefully remove the fabric from the targa hoop using a heat gun and occasionally a putty knife. The adhesive used is the same contact cement used to glue Formica laminate to counter tops. Once removed I temporarily locked the targa bar in place with pieces of pipe insulation and tape. Then I started pulling the fabric forward and to the sides (both directions) until I figured out what had to be done to get the wrinkles and waves out. In my case the fabric had to be pulled forward about an inch and then to the sides, one more than the other. It was at this point I decided it was a job for a professional. When I took it to the shop they did same experimental tugging and stretching, then shot the adhesive on the bar and the underside of the cloth. I held the bar locked in place while two of them started pulling the fabric until the vinyl window was as tight as they could get it, then pressed the adhesive prepared edges in place on the bar. Once in place they trimmed off the excess fabric, opened the targa panel slots and worked their way down the sides finally doing a nice tuck and fold at the bottom of the bar. Some advice: plan to do the job with the fabric and vinyl warm to allow them to stretch. A hot day is a good idea. Make sure the Velcro strips on the sides can still be engaged with those on the body. If doing it yourself, memorize the tuck and fold used to finish the bottoms of the targa hoop. You'll likely have extra fabric there.

Best of luck.