Tamiya 1:12 McLaren MP4/6 Rebuild/Upgrade

Tamiya 1:12 McLaren MP4/6 Rebuild/Upgrade

Author
Discussion

dr_gn

Original Poster:

16,140 posts

183 months

Saturday 10th May 2014
quotequote all
So further to this thread on my MP4/6 I built back in about 1999/2000:

http://www.pistonheads.com/GASSING/topic.asp?h=0&a...

I finally made a start: I put the model on EBay with the intention of using the cash to buy a new kit to super-detail. After looking at the photos I'd taken I decided I couldn't part with it and ended the auction early. I'm on the F1M forum and a few people said why not partially rebuild it "kerbside" and then get another to buildup as a super detailled chassis? That is exactly what I'm intending to do with my MP4/4's, so that's what I'm going to do with this one. They will go on a base with my Senna and Berger autographs and my old ticket to the 1991 BGP. Likewise the MP4/4's will have my other Senna autograph along with Prost's and my '88 ticket.

Anyway, here are the "before" pics:









Doesn't look bad does it? That's until you look a bit closer:





Makes me wonder how I could ever have thought it was a good model, even 15 years ago...

I've now stripped it to the extent I need to correct the paint and add a few bells and whistles. A lot of it is bolt together, and luckily I'd not been too careful about removing paint from the bonded surfaces when I built it, so most of them cracked apart with little or no damage:



The decals on the radiators silvered, and always looked a bit naff. They will be partially stripped and re-ainted with Alclad and a proper wash (now I know how to do a wash!), since they are clearly visible with the body fitted:



Wing end plates are hand painted on the insides. They might get a carbon decal, or just new paint:



Same with the front wing endplates. Even though I sprayed the parts, it was with a TS can, and the paint was too thick, plus I got dust on them:



All body and wing incidence fasteners will be replaced with p/e parts. I'll apply carbon decals on all visible surfaces where necessary, e.g. brake ducts, vortex generators etc.

First job will be to strip the body paint with Modelstrip, and repaint and re-decal. Then make a start on detailling the wheels.

Edited by dr_gn on Saturday 10th May 15:10

bristolracer

5,527 posts

148 months

Saturday 10th May 2014
quotequote all
Always fancied a 1/12th scale model.

Not sure my skills could do it justice.
Good luck and keep us posted.

dr_gn

Original Poster:

16,140 posts

183 months

Saturday 10th May 2014
quotequote all
bristolracer said:
Always fancied a 1/12th scale model.

Not sure my skills could do it justice.
Good luck and keep us posted.
The Tamiya 1:12 F1 kits are pretty easy to build, with no extra details. The parts are all pretty large, although there are some small screws to hold the main parts together. So long as you can use a spray can and mask they're not so daunting.

dr_gn

Original Poster:

16,140 posts

183 months

Saturday 10th May 2014
quotequote all
Made a proper start tonight by machining the wheels to fit the Formula Perfect spindles and nuts. FP do two kits; one is a complete replacement brake rotor/bell/spindle/nut set (for display with wheels off) and the spindle and nut set only for a kerbside model:



Luckily the Tamiya kit is so nicely engineered that retro-fitting these fairly fundamental parts is made a lot easier by the bolted joints on much of the suspension and structural parts. All this was stripped without having to break any glue bonds:





Each wheel hub requires drilling through to enlarge the original hole, counterboring and finally the most important part, chamfering to form a seat for the nut. This chamfer is what will ultimately help to centre the wheel, much like the real thing. All the tooling is provided in the FP kit:



Here are wheels showing before and after machining; there is not much left of the outer hub boss after chamfering:



Here are the finished wheels with the axles and nuts dropped in:



The axles fit into machined aluminium bosses that replace the plastic equivalents in the kit. The machining and fit is great:



I still need to figure out what colour the nuts were. I'm not sure whether they were blue and red anodised, or something else.

Red Firecracker

5,276 posts

226 months

Sunday 11th May 2014
quotequote all
Looking good, nice when they come apart as easily as the go together. Have you thought about a mask for the radiator lettering?

I think you're right on the wheel nuts, no red & blue, just natural. This pic tends to agree;

http://www.f1-fansite.com/wp-content/uploads/2014/...

dr_gn

Original Poster:

16,140 posts

183 months

Sunday 11th May 2014
quotequote all
Red Firecracker said:
Looking good, nice when they come apart as easily as the go together. Have you thought about a mask for the radiator lettering?

I think you're right on the wheel nuts, no red & blue, just natural. This pic tends to agree;

http://www.f1-fansite.com/wp-content/uploads/2014/...
Yeah, I though about a mask, in fact Paul at TV said he'd get one photo-etched and send it me. Not all the radiators appear to have had the lettering, so if I cant get a template I'll leave them silver.

I've got some reference pics from 90's F1 test sessions I used to go to, and I can't see red or blue wheel nuts, just what looks like dark bronze. I wonder if the nuts were painted for the race?

The link you posted doesn't work for me.

Cheers.

Red Firecracker

5,276 posts

226 months

Sunday 11th May 2014
quotequote all
Hmm, strange. It's a large pic so linked rather than posted direct, but what the hell;



which is linked to this video;

https://www.youtube.com/watch?v=Mk9e0WgPAr0

dr_gn

Original Poster:

16,140 posts

183 months

Sunday 11th May 2014
quotequote all
Red Firecracker said:
Hmm, strange. It's a large pic so linked rather than posted direct, but what the hell;



which is linked to this video;

https://www.youtube.com/watch?v=Mk9e0WgPAr0
The picture link there appears to be broken hehe

I've got that video bookmarked already - plenty of good stuff.

I'm ordering the Joe Honda book today, it's always good to have a paper reference.

Cheers.

Red Firecracker

5,276 posts

226 months

Sunday 11th May 2014
quotequote all
dr_gn said:
The picture link there appears to be broken hehe

I've got that video bookmarked already - plenty of good stuff.

I'm ordering the Joe Honda book today, it's always good to have a paper reference.

Cheers.
Works fine for me, lovely picture, perfect image of wheel nuts in period tongue outbiggrin

You could email McLaren. I've heard they're actually very approachable so nothing ventured etc, maybe get a list together and engage the historics department. All my Goodwood pics show them as being natural metal rather than coloured as well.

Now, back to Monaco Historics on Motors.

dr_gn

Original Poster:

16,140 posts

183 months

Sunday 11th May 2014
quotequote all
So here are some references I've got in my office. First off a 1991 or 1992 [ETA Jordan 191 or 192) rear tyre complete with the hand written markings. Ignore the wheel, it's an old F3000 item that I had and decided to use for a table:









Here's '90's F1 tyre valve cap. I blagged loads of these from GoodYear at various F1 test sessions back in the day. All my cars and bikes, and friends cars and bikes had them at one point!



These are some carbon brake rotors from - I think - a Stewart. Not sure of the year, but the colour and grain will be similar to earlier versions. My original 1:12 rotors are in the middle:





Edited by dr_gn on Sunday 11th May 18:12


Edited by dr_gn on Sunday 11th May 23:06

dr_gn

Original Poster:

16,140 posts

183 months

Sunday 11th May 2014
quotequote all
Drilled out the brake rotors tonight to suit the new spindles. I deviated a bit from the TV instructions and used a 3.3mm drill rather than a clearance hole, in order to give a bit more support:


dr_gn

Original Poster:

16,140 posts

183 months

Monday 12th May 2014
quotequote all
I wasn't convinced that my usual brake fluid paint stripping method would work so well on 15 year old paint, so I tried it on some of the smaller body/wing parts:



Needn't have worried, it worked beautifully; the paint just fell off after 24 hours of immersion. They are now drying after a thorough toothbrushing with hot detergent, and only require a few small areas of solid paint to be scraped away. I've now put the nose cone and radiators in the bath.

I couldn't prise open the front wing halves, so I'll use Modelstrip on that assembly. The last thing I want is to get brake fluid trapped inside only to seep out after repainting. There is no disadvantage to leaving them as a unit anyway. I'll also use Modelstrip on the main body becasue it's too big to immerse in fluid.

An F1M forum member supplied me with some spare decals, which is a big step on the way to me completing this rebuild:


dr_gn

Original Poster:

16,140 posts

183 months

Tuesday 13th May 2014
quotequote all
The nose and radiators are now stripped. The nose looks like brand new, even retaining its original gloss finish. The radiators don't look much different, but then again they are silver plastic underneath the silver paint.



Like a plasterer's radio: The body and front wing were coated in Modelstrip. It needed thinning with water, but went on OK:



It's now in the airing cupboard in a plastic bag to delay the stuff drying out (Modelstrip is pretty ineffective when dry). Even after 1 hour I can see unspeakable chemical warfare type things happening in there:



If that doesn't work, I'll buy a load of cheap brake fluid and shove it all in a bucket for a couple of days.

In an almost unprecidented stroke of luck, I seem to have found all the paint I need to refinish the body. Something is bound to go wrong...I think the Flourescent Red might even be spare from the first time around:


Red Firecracker

5,276 posts

226 months

Wednesday 14th May 2014
quotequote all
Decant and airbrush or straight from the can?

I wonder how many ingredients ModelStrip shares with oven cleaner as well!

fatboy69

9,371 posts

186 months

Wednesday 14th May 2014
quotequote all
I hope that the model will reappear sporting the Marlboro decals.

This thread might give me the inspiration to actually build my MP4/6.

It has been in the box untouched since I bought it god knows how many years ago, along with the Williams FW14, as well as a Porsche 934 & 935.

One day. Maybe!

dr_gn

Original Poster:

16,140 posts

183 months

Wednesday 14th May 2014
quotequote all
Red Firecracker said:
Decant and airbrush or straight from the can?

I wonder how many ingredients ModelStrip shares with oven cleaner as well!
Definitely decant into the airbrush. The last paint was from the can and it was too thick and degassed through the surface.

I've got a thread running on F1M and there is a lot of advice on refinishing there. A bit of conflicting advice on clearcoats. I was going to decant some TS clear, but apparently it's too aggressive on decals, so someone suggested the Tamiya X- acrylic pot varnish, but someone else said it might yellow. No way I'm ever using Zero varnish again, so I'm a bit stuck on the final coat.

Edited by dr_gn on Wednesday 14th May 09:24

dr_gn

Original Poster:

16,140 posts

183 months

Wednesday 14th May 2014
quotequote all
fatboy69 said:
I hope that the model will reappear sporting the Marlboro decals.

This thread might give me the inspiration to actually build my MP4/6.

It has been in the box untouched since I bought it god knows how many years ago, along with the Williams FW14, as well as a Porsche 934 & 935.

One day. Maybe!
This is only kerbside - I'm not touching anything under the body apart from the radiators and maybe some other very small details visible from outside the car.

The body will be fully detailed as necessary, but this is really just a starter for the main course which is the fully detailed bare chassis. A lot of work and investment to come (then there's the Ferrari and Williams to do!).

If you want to sell your MP4/6 I'd have it off you. I'm looking for one on EBay at the moment.

Cheers.

dr_gn

Original Poster:

16,140 posts

183 months

Wednesday 14th May 2014
quotequote all
The Modelstrip worked on the front wing and about 95% of the body, but for some reason the front area of fluourescent red was pretty much untouched:



I've sprayed it with Mr.Muscle and will see what happens. If it's still there later, it'll be going in brake fluid:


g3org3y

20,606 posts

190 months

Wednesday 14th May 2014
quotequote all
Great work doc. Watching this thread with interest.

Red Firecracker

5,276 posts

226 months

Wednesday 14th May 2014
quotequote all
dr_gn said:
Definitely decant into the airbrush. The last paint was from the can and it was too thick and degassed through the surface.

I've got a thread running on F1M and there is a lot of advice on refinishing there. A bit of conflicting advice on clearcoats. I was going to decant some TS clear, but apparently it's too aggressive on decals, so someone suggested the Tamiya X- acrylic pot varnish, but someone else said it might yellow. No way I'm ever using Zero varnish again, so I'm a bit stuck on the final coat.

Edited by dr_gn on Wednesday 14th May 09:24
Good to hear about the decanting, was slightly concerned for a minute.

Completely understand about the Zero clear. I've tried and tried to replicate the issues you had with no success, but there's no point at all in going with a product you have no confidence in.