Toms Garden Shed / Workshop / Office Build
Discussion
Thanks for the kind words everyone, it's appreciated.
Daniel, the office will be plasterboard over OSB to give lots of bite for screws etc when hanging shelves and the like. The office end will also be fitted with skirtings, decent flooring etc. I want it to feel like it could be inside the house.
The shed end will remain OSB for durability.
Daniel, the office will be plasterboard over OSB to give lots of bite for screws etc when hanging shelves and the like. The office end will also be fitted with skirtings, decent flooring etc. I want it to feel like it could be inside the house.
The shed end will remain OSB for durability.
Hmmm. There is a reason we leave our out-houses a bit rustic on the interior. Deck it out like your house and you'll find that it's no longer a man cave one day but a children's TV room or the wife's pilates studio. They do like their lebensraum.
Very impressive build and top skills. Have enjoyed your thread. Thanks.
Very impressive build and top skills. Have enjoyed your thread. Thanks.
cylon said:
so what has the cost come in at? so far..
£3400 including the plasterboard, cladding and electric stuff. I still need to pay for an electrician, flooring, lighting and of course furniture, plus sundries like paint and skirtings etc. I hope to be at £4200 ish for the building once done, which I think is incredibly good value for the spec.
I'll upload a breakdown once it's all finished and everything is accounted for, but I've been logging all my receipts as I go.
I am seriously bored of cutting and installing insulation. Over 200 individual pieces, but hey at least it was cheap. *sigh*.
I'm pleased to say that it is done!
I'm also delighted to say that I've got wood!
IMG_3110 by Tomoose85, on Flickr
IMG_3112 by Tomoose85, on Flickr
I'm very pleased with the quality and the service from York Timber.
I have also cut through the end wall and fitted a door frame. I think I am going to construct the 'shed' door in the same way as the walls to make it easy to block off in the future, but any other ideas are welcomed
IMG_3116 by Tomoose85, on Flickr
And finally, I have made a start on the electrics. This will be my charging area.
IMG_3117 by Tomoose85, on Flickr
I need to run all the cables in before I can install the breather membrane and the cladding. I've got a Paslode gun on hire starting tomorrow, so 1 week to get the cladding on. Full steam ahead!
Also, if anyone knows a friendly electrician in the Northamptonshire/Bedfordshire area then please do put them/me in touch, as I do want it all to be connected up and signed off by a pro. Thanks!
I'm pleased to say that it is done!
I'm also delighted to say that I've got wood!
IMG_3110 by Tomoose85, on Flickr
IMG_3112 by Tomoose85, on Flickr
I'm very pleased with the quality and the service from York Timber.
I have also cut through the end wall and fitted a door frame. I think I am going to construct the 'shed' door in the same way as the walls to make it easy to block off in the future, but any other ideas are welcomed
IMG_3116 by Tomoose85, on Flickr
And finally, I have made a start on the electrics. This will be my charging area.
IMG_3117 by Tomoose85, on Flickr
I need to run all the cables in before I can install the breather membrane and the cladding. I've got a Paslode gun on hire starting tomorrow, so 1 week to get the cladding on. Full steam ahead!
Also, if anyone knows a friendly electrician in the Northamptonshire/Bedfordshire area then please do put them/me in touch, as I do want it all to be connected up and signed off by a pro. Thanks!
Crumpet said:
Great thread! Might be a silly question but how did you fix and set the 4x4 corner (fence) posts?
No such thing as a stupid question, just stupid people The wall frames are screwed into the brick with frame fixings, the frames simply screw into the fence posts to hold them in place and square etc.
PartOfTheProblem said:
No such thing as a stupid question, just stupid people
The wall frames are screwed into the brick with frame fixings, the frames simply screw into the fence posts to hold them in place and square etc.
I can't argue with that!The wall frames are screwed into the brick with frame fixings, the frames simply screw into the fence posts to hold them in place and square etc.
I had envisaged that the fence posts were set into the base somehow and provided most of the support and strength! Is it the boarding that provides rigidity and strength? (Sorry another stupid question - I've got tons of 'em!)
Crumpet said:
I can't argue with that!
I had envisaged that the fence posts were set into the base somehow and provided most of the support and strength! Is it the boarding that provides rigidity and strength? (Sorry another stupid question - I've got tons of 'em!)
The 3x2 framework at 450mm centres with noggins at the mid point is surprisingly sturdy. The fence posts are just for the corners and are proud of the studwork to protect the endgrain of the cladding once installed. I had envisaged that the fence posts were set into the base somehow and provided most of the support and strength! Is it the boarding that provides rigidity and strength? (Sorry another stupid question - I've got tons of 'em!)
The framework is screwed down into the brickwork and slab. The roof joists then tie the walls together to stiffen things up. The OSB on the walls is the icing on the cake in making everything rigid. The cladding will only add to the rigidity of the structure.
I hope this helps?
Tom
So, a bit more progress has been made.
All first fix electrics are done. I ran the ring main cables around the wall plate dropping them down to each socket. Cables have been clipped to the outside of studs, but under the breather membrane. I squirted a bit of expanding foam in all of the holes to keep the building nice and toasty as far as possible.
IMG_3146 by Tomoose85, on Flickr
IMG_3187 by Tomoose85, on Flickr
Charging area:
IMG_3150 by Tomoose85, on Flickr
Metal clad sockets wired up.
IMG_3152 by Tomoose85, on Flickr
And a couple of face plates on
IMG_3154 by Tomoose85, on Flickr
Next up was breather membrane:
IMG_3195 by Tomoose85, on Flickr
IMG_3198 by Tomoose85, on Flickr
And then some cladding at last! This is mounted on roofing battens but I didn't get a photo of those
IMG_3208 by Tomoose85, on Flickr
IMG_3209 by Tomoose85, on Flickr
IMG_3212 by Tomoose85, on Flickr
I'm really pleased the cladding ended up flush with the posts too!
IMG_3213 by Tomoose85, on Flickr
IMG_3214 by Tomoose85, on Flickr
I'm hoping to finish the cladding tomorrow.
Comments or questions welcome as usual, thanks
All first fix electrics are done. I ran the ring main cables around the wall plate dropping them down to each socket. Cables have been clipped to the outside of studs, but under the breather membrane. I squirted a bit of expanding foam in all of the holes to keep the building nice and toasty as far as possible.
IMG_3146 by Tomoose85, on Flickr
IMG_3187 by Tomoose85, on Flickr
Charging area:
IMG_3150 by Tomoose85, on Flickr
Metal clad sockets wired up.
IMG_3152 by Tomoose85, on Flickr
And a couple of face plates on
IMG_3154 by Tomoose85, on Flickr
Next up was breather membrane:
IMG_3195 by Tomoose85, on Flickr
IMG_3198 by Tomoose85, on Flickr
And then some cladding at last! This is mounted on roofing battens but I didn't get a photo of those
IMG_3208 by Tomoose85, on Flickr
IMG_3209 by Tomoose85, on Flickr
IMG_3212 by Tomoose85, on Flickr
I'm really pleased the cladding ended up flush with the posts too!
IMG_3213 by Tomoose85, on Flickr
IMG_3214 by Tomoose85, on Flickr
I'm hoping to finish the cladding tomorrow.
Comments or questions welcome as usual, thanks
So, some good progress was made today with the cladding. I got it all done other than the top pieces which need cutting to match the roof pitch.
I got very frustrated with the Paslode brad gun I hired from HSS. To start with they gave me the wrong charger cable, luckily I had a lead that worked, but all day the firing has been very intermittent I've wanted to smash the thing to pieces. It really held up progress.
Oh well, on to some pics!
Battens screwed on. Note the breather membrane overlaps the brick slightly so any moisture can run down the back of the cladding without the stud work getting wet
IMG_3222 by Tomoose85, on Flickr
IMG_3221 by Tomoose85, on Flickr
IMG_3224 by Tomoose85, on Flickr
IMG_3223 by Tomoose85, on Flickr
Then on with the cladding!
IMG_3229 by Tomoose85, on Flickr
IMG_3228 by Tomoose85, on Flickr
IMG_3234 by Tomoose85, on Flickr
IMG_3235 by Tomoose85, on Flickr
IMG_3243 by Tomoose85, on Flickr
IMG_3245 by Tomoose85, on Flickr
I'm really pleased with the detailing too, it worked out great.
Cladding end grain protected by the corner posts
IMG_3231 by Tomoose85, on Flickr
And the intermediate post on the long wall to avoid needing to have any joints in the cladding.
IMG_3232 by Tomoose85, on Flickr
The gravel board around the window frame seems to do the job nicely.
IMG_3236 by Tomoose85, on Flickr
So the next jobs are to cut the top boards to fit and get them on, make a door for the end wall, find some way of doing the soffits (probably with gravel boards), and get the electrics finished off.
As for paint, I think I'm going to try and find a colour to match the windows for the soffits and fascias, but the rest will be something like Sadolin 'Autumn Leaf'.
I got very frustrated with the Paslode brad gun I hired from HSS. To start with they gave me the wrong charger cable, luckily I had a lead that worked, but all day the firing has been very intermittent I've wanted to smash the thing to pieces. It really held up progress.
Oh well, on to some pics!
Battens screwed on. Note the breather membrane overlaps the brick slightly so any moisture can run down the back of the cladding without the stud work getting wet
IMG_3222 by Tomoose85, on Flickr
IMG_3221 by Tomoose85, on Flickr
IMG_3224 by Tomoose85, on Flickr
IMG_3223 by Tomoose85, on Flickr
Then on with the cladding!
IMG_3229 by Tomoose85, on Flickr
IMG_3228 by Tomoose85, on Flickr
IMG_3234 by Tomoose85, on Flickr
IMG_3235 by Tomoose85, on Flickr
IMG_3243 by Tomoose85, on Flickr
IMG_3245 by Tomoose85, on Flickr
I'm really pleased with the detailing too, it worked out great.
Cladding end grain protected by the corner posts
IMG_3231 by Tomoose85, on Flickr
And the intermediate post on the long wall to avoid needing to have any joints in the cladding.
IMG_3232 by Tomoose85, on Flickr
The gravel board around the window frame seems to do the job nicely.
IMG_3236 by Tomoose85, on Flickr
So the next jobs are to cut the top boards to fit and get them on, make a door for the end wall, find some way of doing the soffits (probably with gravel boards), and get the electrics finished off.
As for paint, I think I'm going to try and find a colour to match the windows for the soffits and fascias, but the rest will be something like Sadolin 'Autumn Leaf'.
This is absolutely brilliant - well done, I would be super pleased with myself if I'd managed to do something like this!
Is there anything that you would have approached/done differently if you were going to do it again? (i.e. advice you would give to someone like me who is enthused by this project!).
What are you going to do with the inside? Plasterboard and skim?
Looking good - great project!
Is there anything that you would have approached/done differently if you were going to do it again? (i.e. advice you would give to someone like me who is enthused by this project!).
What are you going to do with the inside? Plasterboard and skim?
Looking good - great project!
Gassing Station | Homes, Gardens and DIY | Top of Page | What's New | My Stuff