Raw metal radiators
Discussion
Trying to find modern rads in raw metal (lacquered)
All I can seem to find are fairly traditional ‘school’ radiators and although I really like them, my house is probably a bit too modern to carry them off.
Anyone know of anywhere I can get either horizontal panel or tube rads in raw metal?
Tia...
All I can seem to find are fairly traditional ‘school’ radiators and although I really like them, my house is probably a bit too modern to carry them off.
Anyone know of anywhere I can get either horizontal panel or tube rads in raw metal?
Tia...
Take a look here: >> http://www.featureradiators.co.uk/Contemporary.htm
Specifically Core, Bare Metal Classic, Press
They also do Eskimo Gong which is flat panel type with a distressed metal finish
Specifically Core, Bare Metal Classic, Press
They also do Eskimo Gong which is flat panel type with a distressed metal finish
you might try these.
https://www.theradiatorcompany.co.uk/about-us/
they paint to order, so presumably they have unpainted rads somewhere.
https://www.theradiatorcompany.co.uk/about-us/
they paint to order, so presumably they have unpainted rads somewhere.
Look like mine which are made by 'revive' I think. Got mine from mrcentralheating.co.uk who seemed to be the cheapest I could find at the time. Also have zehnder versions in which which really show up Just how much dust they gather! The raw metal ones don't show this and everyone comments on how good they look
From here - https://loveradiators.com/MHS-Multisec-Bespoke-Mad...
Very helpful people.
I’ve had one bespoke as I needed a total of 8000btu over two rads, but wanted a specific size and only two columns on one of the rads.
2 columns
Depth: 66mm
Height: 500mm
Width: 990mm
Output: 2873
£412.92
3 columns
Depth: 107mm
Height: 600mm
Length: 1220mm
Output: 5783
£580.00
Very helpful people.
I’ve had one bespoke as I needed a total of 8000btu over two rads, but wanted a specific size and only two columns on one of the rads.
2 columns
Depth: 66mm
Height: 500mm
Width: 990mm
Output: 2873
£412.92
3 columns
Depth: 107mm
Height: 600mm
Length: 1220mm
Output: 5783
£580.00
dazm said:
Look like mine which are made by 'revive' I think. Got mine from mrcentralheating.co.uk who seemed to be the cheapest I could find at the time. Also have zehnder versions in which which really show up Just how much dust they gather! The raw metal ones don't show this and everyone comments on how good they look
Mr central heating are very cheap in comparison, but don’t do the sizes I needed.They look superb OP. Be sure to post a pic when they're hung.
https://www.mrcentralheating.co.uk/1800h-x-490w-2-...
Loads of options for powder coated available. 1800 x 383 doubles or 1800 x 293 triples would be perfect for me.
https://www.radiatorhut.co.uk/vertical-radiators/c...
dazm said:
Look like mine which are made by 'revive' I think. Got mine from mrcentralheating.co.uk who seemed to be the cheapest I could find at the time. Also have zehnder versions in which which really show up Just how much dust they gather! The raw metal ones don't show this and everyone comments on how good they look
Yes, spotted those. Limited in sizes though. I need tall but not too wide.https://www.mrcentralheating.co.uk/1800h-x-490w-2-...
Loads of options for powder coated available. 1800 x 383 doubles or 1800 x 293 triples would be perfect for me.
https://www.radiatorhut.co.uk/vertical-radiators/c...
Good choice, I'm currently midway through a Georgian house refurb and like the traditional look with a nod towards moderns colours and textures. If in future tastes and fashions change I can remove and get them sprayed a different colour.
I got mine from www.columnrads.co.uk and was very happy with the service. To be honest they all probably source from the same supplier. But I intend to change out every single radiator in the house for these. So far 6 down, 8 to go!
What TRV's did you go for? I've used Bentley Traditional silver nickel and they suit the radiators perfectly.
I got mine from www.columnrads.co.uk and was very happy with the service. To be honest they all probably source from the same supplier. But I intend to change out every single radiator in the house for these. So far 6 down, 8 to go!
What TRV's did you go for? I've used Bentley Traditional silver nickel and they suit the radiators perfectly.
MellowshipSlinky said:
TRV’s aren’t something I’ve bought yet.
Need something to match, or even go black if need be, which would tie in with the black 3D metal tiles going on the wall behind the stove...
These are the silver Nickel. All depends on the type of property really. I'd have liked to go Wifi TRV's but they all look like arse.Need something to match, or even go black if need be, which would tie in with the black 3D metal tiles going on the wall behind the stove...
WP_20181111_21_28_59_Rich[1] by Lee Watkinson, on Flickr
Gassing Station | Homes, Gardens and DIY | Top of Page | What's New | My Stuff