Brake caliper sliding pin grease

Brake caliper sliding pin grease

Author
Discussion

Howard-

Original Poster:

4,952 posts

202 months

Monday 28th December 2009
quotequote all
I've searched the internets high and low and can't find a definitive answer... What type of grease should I use to lubricate the pins that the caliper slides on? (MX5 FWIW)

I know I need to use copper grease for the back of the pads and where they move on the carrier but what about the pins?


Cheers cool

road_rager

1,091 posts

199 months

Monday 28th December 2009
quotequote all
I always thought that you just gave them a good clean and NOT use grease in the sliders as dirt can mix with it and cause wear and sticking

mcford

819 posts

174 months

Monday 28th December 2009
quotequote all
I usually use a smear of copper grease. They are usually protected by rubber boots that will keep the dirt out, but not always the moisture, which will lead to corrosion and seizing up. Wear due to erosion by grit shouldn't really be a problem as their movement during operation is quite limited.

r11co

6,244 posts

230 months

Monday 28th December 2009
quotequote all
Arrgh! Copper grease is a bad choice as it is petroleum based and will soften and damage the boots on the caliper slides.

The correct grease is a silicone based one, and the only way I have managed to get hold if it is in small tubes as part of replacement slider pin kits.

ExPat2B

2,157 posts

200 months

Monday 28th December 2009
quotequote all
You want red brake grease. Its a rubber compatiable grease.

bimsb6

8,040 posts

221 months

Monday 28th December 2009
quotequote all
ExPat2B said:
You want red brake grease. Its a rubber compatiable grease.
can be quite difficult to get hold of over the counter ,i know i've tried recently !

pits

6,429 posts

190 months

Monday 28th December 2009
quotequote all
I believe halfords sell it, failing that I also think your local Mitsubishi garage sells it, as Mitsi brakes have a tendency of being under specced for the cars and get very hot, so need the proper grease.

tr7v8

7,192 posts

228 months

Monday 28th December 2009
quotequote all
bimsb6 said:
ExPat2B said:
You want red brake grease. Its a rubber compatiable grease.
can be quite difficult to get hold of over the counter ,i know i've tried recently !
I've struggled in the past & then found various sellers on E bay of all things.

Benmac

1,468 posts

216 months

Monday 28th December 2009
quotequote all
Had similar difficulty myself getting some. Opus oils sell it in nice big tubs I eventually found out.

_Batty_

12,268 posts

250 months

Monday 28th December 2009
quotequote all
lithium grease.
copper grease is the exact opposite of what you want!

AndyS2

869 posts

258 months

Monday 28th December 2009
quotequote all
bimsb6 said:
ExPat2B said:
You want red brake grease. Its a rubber compatiable grease.
can be quite difficult to get hold of over the counter ,i know i've tried recently !
I got mine from here:-

http://www.frost.co.uk/item_Detail.asp?productID=9...

strudel

5,888 posts

227 months

Tuesday 19th August 2014
quotequote all
Adding to an old thread - is Red Rubber grease still the best thing to use or are there better alternatives now? If so, does anyone know of any stockists I can pick up from instead of waiting several days from the net? (The squeaking is driving me berserk).

Ta smile

Dinodelta

6 posts

241 months

Thursday 17th September 2015
quotequote all
Red rubber grease is veggie based and will wash away easily so used for seal assembly.
Normal grease and lithium can react with 'rubber' components depending on the make up of the grease and rubber.
Silicone grease for sliding pins as water resistant and safe with rubber.
A 20g tube of Carlube silicone grease on ebay was £2.69 with postage.

dsayer1979

1 posts

48 months

Tuesday 14th April 2020
quotequote all
An old post but hopefully someone will see it 😬 can I use silicone grease on the sliders, pad guides and piston

SebringMan

1,773 posts

186 months

Thursday 30th July 2020
quotequote all
Yes, you can