The Joy of Running an Old Shed (Vol 2)
The Joy of Running an Old Shed (Vol 2)
Author
Discussion

Steve_F

881 posts

225 months

Monday 5th October
quotequote all
CV boot was split on my old Focus, didn't catch it in time so repacking with grease was totally unsuccessful.

Fun repair thanks to two orders of the wrong driveshaft (sites that don't return the correct part with the reg number inserted can do one...) and the gearbox oil leaking all over the garage floor with the old driveshaft out, not a drip seen when it was taken out or I'd have put the old one back in, and overnight all over the floor.
,
Over a month later its back on the road, with a new noise coming from that end, and MOT running out this week, with an ABS light constantly on. Wondering if I should even have bothered repairing it! Had an advisory for many years for rusty subframe so out with thewire brush and hammerite direct to rust spray paint while I was under it. Tester is going to be amazed at my precision job with the only colour I could find (silver) and no thoughts or cares given to overspray smile

Think I'm going to need some luck to keep it going until my new car arrives. I like running an old shed, but when all 3 of my vehicles are in that category I'm finding it a bit tiring!

A500leroy

8,588 posts

149 months

Monday 5th October
quotequote all
13 months MOT on the gold 92k mile Ka, was going to sell it, but the tester commented how fabulous mine is and they only buy them for courtesy cars themselves, so guess I'll sell the Tigra next spring.

Xenoous

2,514 posts

89 months

Monday 5th October
quotequote all
Well, uh-oh, the results are in.

Symptoms are: Car spluttered then died. Will not even crank when turning key, with Engine Malfunction and accompanying alarm. Error codes are as follows:

Recovery Guys Code Reader said:
P0121:00-AF Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance
P0122:00-AF Throttle/Accelerator Pedal Position Sensor A Circuit Input Low
P0221:00-AF Throttle/Pedal Position Sensor/Switch B Circuit Range/Performance
P0222:00-AF Throttle/Pedal Position Sensor #B Circuit Low Input
P1585:00-AF Throttle Control Fault
P2110:00-AF Throttle Actuator Control System Forced RPM Limit
P2121:00-AF Throttle/Pedal Position Sensor/Switch D Circuit Range/Performance Error
P2122:00-AF Throttle/Pedal Position Sensor/Switch D Circuit Low
P2138:00-2E Throttle/Pedal Position Sensor/Switch D & E Voltage Correlation
P1607:82-28 MIL (Malfunction Indicator Lamp) Output Circuit

U3001:00-08 Control Module Improper Shutdown Performance
U0100:00-08 Missing Communication With ECM/PCM A
U0401:68-8A Data Received From ECM/PCM A Is Invalid

P1607:82-28 MIL Output Circuit
U0401:68-2B Data Received From ECM/PCM A Is Invalid

C2003:49-28 Steering Wheel Switch Left Module
B10AC:95-28 Cruise Control Switch
B1108:77-68 Driver's Door Central Locking Motor
B112B:07-28 Steering Wheel Module
B1D00:13-6B Left Low Beam
B1D01:13-6B Right Low Beam
This guy goes through a car with the exact same issue as mine...



Edited by Xenoous on Monday 5th October 13:20

benny.c

3,797 posts

238 months

Tuesday 6th October
quotequote all
This was my Dad’s shopping/running around car for when he didn’t want to take the XC90 out. Proper grandad spec - 1.4 auto with only 22K miles. When he passed away three years ago, Mum said she wanted to keep it for my son for when he passed his test. That day has come and I need to get it back on the road - my lad is quite fond of it even though we have an Up he can use.

I reckon it’s not been run for four years and what I should have done is moved it every once in a while - but I didn’t. I drained the tank and with fresh fuel it started straight away. A little rough to start with but now really smooth. I’ve done the front discs and pads, adjusted the rear drums and changed the brake fluid. Other than that it’s just been new plates and wipers.

I’m taking it for an MOT in a few hours time so fingers crossed it does OK. If it does then it might get a machine polish to try and restore some redness smile





CaptainScarlet1967

606 posts

16 months

Tuesday 6th October
quotequote all
benny.c said:
This was my Dad s shopping/running around car for when he didn t want to take the XC90 out. Proper grandad spec - 1.4 auto with only 22K miles. When he passed away three years ago, Mum said she wanted to keep it for my son for when he passed his test. That day has come and I need to get it back on the road - my lad is quite fond of it even though we have an Up he can use.

I reckon it s not been run for four years and what I should have done is moved it every once in a while - but I didn t. I drained the tank and with fresh fuel it started straight away. A little rough to start with but now really smooth. I ve done the front discs and pads, adjusted the rear drums and changed the brake fluid. Other than that it s just been new plates and wipers.

I m taking it for an MOT in a few hours time so fingers crossed it does OK. If it does then it might get a machine polish to try and restore some redness smile




That's a cracking resurrection. A FOTU classic right there.

Have you kept those original numberplates? Depending on how original you want it to look, they add a huge degree of 'period' character, more than the current Charles Wright standard.

Due to work commitments these past 5 years, I often leave my shed standing for months on end. Disconnecting the negative battery terminal has been the best way to ensure it starts again. As long as there's decent compression and engine oil levels, starting shouldn't be an issue.

QBee

22,534 posts

175 months

Tuesday 6th October
quotequote all
You swapped it for a new one?
confused

benny.c

3,797 posts

238 months

Tuesday 6th October
quotequote all
Yes I’ve kept the original plates (Smith Knight Fey) but don’t think they’d pass an MOT - the rear one especially is pretty far gone. I’ve fitted one of those battery isolating knobs on the negative terminal which has kept the battery fresh.

The paint looks good in the second photo as it was still wet after a quick jet wash. Now it’s dry it’s gone back to various shades of pink.

bodhi

14,773 posts

260 months

Tuesday 6th October
quotequote all
benny.c said:
Yes I ve kept the original plates (Smith Knight Fey) but don t think they d pass an MOT - the rear one especially is pretty far gone. I ve fitted one of those battery isolating knobs on the negative terminal which has kept the battery fresh. The paint looks good in the second photo as it was still wet after a quick jet wash. Now it s dry it s gone back to various shades of pink.
I had a P reg Golf GTi in the same colour - presumably Tornado Red? - that also likedntirnjng pink. Probably an obvious suggestion but T Cut and a bit of red polish brought it back close to what it should have looked like.

itcaptainslow

4,805 posts

167 months

Tuesday 6th October
quotequote all
benny.c said:
Yes I ve kept the original plates (Smith Knight Fey) but don t think they d pass an MOT - the rear one especially is pretty far gone. I ve fitted one of those battery isolating knobs on the negative terminal which has kept the battery fresh.

The paint looks good in the second photo as it was still wet after a quick jet wash. Now it s dry it s gone back to various shades of pink.
If you want copies made up Retro Plates are excellent, they are a bit pricey though.

benny.c

3,797 posts

238 months

Tuesday 6th October
quotequote all
bodhi said:
I had a P reg Golf GTi in the same colour - presumably Tornado Red? - that also likedntirnjng pink. Probably an obvious suggestion but T Cut and a bit of red polish brought it back close to what it should have looked like.
I did try a bit of cutting compound in a small area and it came back OK so will try a whole panel. Did yours stay red once you’d done it or start fading again?

itcaptainslow said:
If you want copies made up Retro Plates are excellent, they are a bit pricey though.
Let’s see how the MOT goes then it might get a treat!

bodhi

14,773 posts

260 months

Tuesday 6th October
quotequote all
benny.c said:
bodhi said:
I had a P reg Golf GTi in the same colour - presumably Tornado Red? - that also likedntirnjng pink. Probably an obvious suggestion but T Cut and a bit of red polish brought it back close to what it should have looked like.
I did try a bit of cutting compound in a small area and it came back OK so will try a whole panel. Did yours stay red once you d done it or start fading again?
I did use some colour enhancer polish as well (can't remember which one, it was 20 years ago) but it stayed red until I parked it into a hedge at high speed 6 months later.....eek

Seems to be a really common issue with 90's VWs in red - and 00s Honda Civics in red for that matter - but a bit of T Cut and polish generally seems to bring them back to normal (ish).

Just remembered my Golf GTi was from Smith Knight and Fay as well!



benny.c

3,797 posts

238 months

Tuesday 6th October
quotequote all
Thanks. You got six months out of it so that’s encouraging. I’ll try giving it a proper go at the weekend.

MOT was a fail but not catastrophic - a tiny hole (like 10mm) in the cill at the rear.The MOT guy apologised for failing it on such a small thing! Advisories for a cracked tyre but I’ll be changing all of them anyway. Plus brakes a bit weak and surface rust on the suspension components. Pretty chuffed all in, just a bit annoying that I didn’t spot the hole as a bit of stranded filler would have hidden sorted that.

CaptainScarlet1967

606 posts

16 months

Tuesday 6th October
quotequote all
itcaptainslow said:
benny.c said:
Yes I ve kept the original plates (Smith Knight Fey) but don t think they d pass an MOT - the rear one especially is pretty far gone. I ve fitted one of those battery isolating knobs on the negative terminal which has kept the battery fresh.

The paint looks good in the second photo as it was still wet after a quick jet wash. Now it s dry it s gone back to various shades of pink.
If you want copies made up Retro Plates are excellent, they are a bit pricey though.
Good shout there about Retro Plates. I've had a look at them before. About a year ago their prices were around £90 for a pair, IIRC. They disappeared from social media for some reason.

Don't know if they are back at all, but another numberplate website is Plates For Cars:

https://www.platesforcars.co.uk/mobile/designer.ph...

If anyone is planning on ordering older style numberplates from there, somewhat confusingly, they have two ranges called 'UK Old' - one list is numbered 1-4 and the other list contains four years.

I bought a pair last year for a 1997 JDM import and went for a typical font of the time here in the UK, but as the plates would be oblong, I also had to ensure the VRN would fit within the printing machine's margins without being cut off as they can all differ in shape and dimensions. Fortunately that website does provide an accurate preview of how they'll most likely turn out when you choose a font and type in a VRN.

They've got all manner of other options.

They were responsive to e-mails and in the end I think I paid around £63 in total (shipping around £8 from somewhere in Ireland). Worth having a look anyway.

bearman68

4,941 posts

163 months

Wednesday 7th October
quotequote all
Xenoous said:
Well, uh-oh, the results are in.

Symptoms are: Car spluttered then died. Will not even crank when turning key, with Engine Malfunction and accompanying alarm. Error codes are as follows:

Recovery Guys Code Reader said:
P0121:00-AF Throttle/Pedal Position Sensor/Switch A Circuit Range/Performance
P0122:00-AF Throttle/Accelerator Pedal Position Sensor A Circuit Input Low
P0221:00-AF Throttle/Pedal Position Sensor/Switch B Circuit Range/Performance
P0222:00-AF Throttle/Pedal Position Sensor #B Circuit Low Input
P1585:00-AF Throttle Control Fault
P2110:00-AF Throttle Actuator Control System Forced RPM Limit
P2121:00-AF Throttle/Pedal Position Sensor/Switch D Circuit Range/Performance Error
P2122:00-AF Throttle/Pedal Position Sensor/Switch D Circuit Low
P2138:00-2E Throttle/Pedal Position Sensor/Switch D & E Voltage Correlation
P1607:82-28 MIL (Malfunction Indicator Lamp) Output Circuit

U3001:00-08 Control Module Improper Shutdown Performance
U0100:00-08 Missing Communication With ECM/PCM A
U0401:68-8A Data Received From ECM/PCM A Is Invalid

P1607:82-28 MIL Output Circuit
U0401:68-2B Data Received From ECM/PCM A Is Invalid

C2003:49-28 Steering Wheel Switch Left Module
B10AC:95-28 Cruise Control Switch
B1108:77-68 Driver's Door Central Locking Motor
B112B:07-28 Steering Wheel Module
B1D00:13-6B Left Low Beam
B1D01:13-6B Right Low Beam
This guy goes through a car with the exact same issue as mine...



Edited by Xenoous on Monday 5th October 13:20
I seem to remember that when we had exactly this issue, we diconnected the battery, removed the BCM under the glovebox, and connected / disconnected / reconnected all the multi plugs going in there. Corrosion on the pins can be a concern.

Worth a try because it's free and easy.
(Caveat to say that I have not watched the YT video)

GIYess

1,476 posts

132 months

Wednesday 7th October
quotequote all
Sometimes when you have a weak battery or bad earth it can throw up multiple codes like that. Worth looking into that side of things maybe?

Just booked the galaxy in for pre MOT checkup. Bit nervous as it really is getting rough. It's at 166k now. Really want to get it to 200k but not sure what this MOT will throw up.
There is a round dent in the rear passenger door that has been there since I bought it. It had got very rusty and my wife wouldn't drive it so I got my Dremel out, gave it a clean up and slapped some rust converter on. It was grey (on a black car) so I got a permanent marker and coloured it in. 2 washes later and it's still black!

Xenoous

2,514 posts

89 months

Wednesday 7th October
quotequote all
bearman68 said:
I seem to remember that when we had exactly this issue, we diconnected the battery, removed the BCM under the glovebox, and connected / disconnected / reconnected all the multi plugs going in there. Corrosion on the pins can be a concern.

Worth a try because it's free and easy.
(Caveat to say that I have not watched the YT video)
Thanks bearman. I'll absolutely do that, as well as the PCM. The video goes into detail about a broken wire in the wiring loom. A particular comment on said video highlights that single cable being an issue on a few Mondeo's. Apparently it rots at the T junction just below the passenger headlight.

Interestingly the battery is completely dead reading 10v. I might give it a full charge again to see if there's actually anything wrong with it. I removed my known ok battery from the BMW 318i and tested it in the Mondeo with the same result.

In either case, the Mondeo is off the road and BMW back on...

bodhi said:
I'd probably run the BMW primarily but keep the Mondeo going for when the E90 has a strop.
Smart advice... Just the other way round hehe

bodhi

14,773 posts

260 months

Wednesday 7th October
quotequote all
Xenoous said:
Smart advice... Just the other way round hehe
Haha - although it does bring back memories of when we had the Civic. It didn't break, but the leaky boot and lack of working AC meant it was unusable when it was too cold (took ages to defrost) or too cold (it became a sweatbox). In those situations I was back in the BMW it was supposed to keep the mileage off hehe

7 5 7

4,488 posts

142 months

Thursday 8th October
quotequote all
Vecshed.....its going in the garage later this afternoon, my mechanic is looking into a possible (lay shaft bearing re: the gearbox) not exactly good news.

Its been making 'whirring/oscillating' sounds for a while, hense why I got my gearbox oil changed last month, which subsequently had not much oil in it when changed - noise goes when I press the clutch, but present in gear and not in neutral, so this may be the nail in the coffin, who knows....I will report back!

As many know I do quite a lot of miles weekly, and this is something I cant really ignore....as much as I have been, so need to get it checked really, see what the options are....I may be awakening the E90....again (that I am yet to sell if this is terminal for old Veccy) and limping 'literally' that around.


Edited by 7 5 7 on Thursday 8th October 12:09

Steve_F

881 posts

225 months

Friday 9th October
quotequote all
Shed Focus failed its MOT yesterday, CV boot ripped on the side I just replaced the driveshaft (hoping its just the left over grease), wheel bearing and ball joint the main ones. But the one that worried me the most, reverse lights both out... Couple of quid quoted for bulbs but suspect its an electrical issue as the sensors stopped working too.

Have a mental budget of £600, it will get sold once MOT'd (or not) and I think that'll be about the break even point for making my money back versus scrap value. It was my dad's car for 15+ years, did me for the last year in my job switching period where I couldn't order an electric car, want to see it live on but chasing electrical issues could be prohibitive.

Xenoous

2,514 posts

89 months

Friday 9th October
quotequote all
Steve_F said:
Shed Focus failed its MOT yesterday, CV boot ripped on the side I just replaced the driveshaft (hoping its just the left over grease), wheel bearing and ball joint the main ones. But the one that worried me the most, reverse lights both out... Couple of quid quoted for bulbs but suspect its an electrical issue as the sensors stopped working too.

Have a mental budget of £600, it will get sold once MOT'd (or not) and I think that'll be about the break even point for making my money back versus scrap value. It was my dad's car for 15+ years, did me for the last year in my job switching period where I couldn't order an electric car, want to see it live on but chasing electrical issues could be prohibitive.
Sounds like the reverse light switch on the gearbox. I had to replace mine on my Mk2 Focus ST years ago. Not particularly difficult, but did need to take the battery box/tray out if I remember correctly. Appreciate it's a different car...