Project Moff - 600 BHP R33 GTS-t Skyline Race Car
Discussion
We now have a nice new fuel break system fitted. Thanks to Abbey Motorsport for supplying the bits.
Very simple way to drain fuel from the car.
Full info here - http://www.theprojectmoff.co.uk/30-september-2013-...
.
Very simple way to drain fuel from the car.
Full info here - http://www.theprojectmoff.co.uk/30-september-2013-...
.
Hiya All,
Sorry for a delay in updating....
The car is now back with Abbey Motorsport for a little bit of work.
Dyno Run - Bit of a health check to make sure car is performing ok
Suspension alignment - Abbey have a new hunter 4 wheel alignment and geometry set up tool which was recently installed.
Service - Change all the fluids....
Few other bits...
Keep you posted...
Sorry for a delay in updating....
The car is now back with Abbey Motorsport for a little bit of work.
Dyno Run - Bit of a health check to make sure car is performing ok
Suspension alignment - Abbey have a new hunter 4 wheel alignment and geometry set up tool which was recently installed.
Service - Change all the fluids....
Few other bits...
Keep you posted...
Hiya All,
Sorry for a delay in updating....
The car is now back with Abbey Motorsport for a little bit of work.
Dyno Run - Bit of a health check to make sure car is performing ok
Suspension alignment - Abbey have a new hunter 4 wheel alignment and geometry set up tool which was recently installed.
Service - Change all the fluids....
Few other bits...
Keep you posted...
Sorry for a delay in updating....
The car is now back with Abbey Motorsport for a little bit of work.
Dyno Run - Bit of a health check to make sure car is performing ok
Suspension alignment - Abbey have a new hunter 4 wheel alignment and geometry set up tool which was recently installed.
Service - Change all the fluids....
Few other bits...
Keep you posted...
Here is the Dyno run from Abbey Motorsport the other day.
BHP figure is on the right middle (618 at the hubs)
Lb/ft is on the left middle (divided by Diff Ratio which is 4.111:1, giving about 475 lb/ft)
Its maxing out the injectors, so has been set back a little form this run
https://www.youtube.com/watch?v=oFH4mg3w_jg
Weather is looking like it might be dry, I can't wait for this Sunday !!!
Here is the Dyno run from Abbey Motorsport the other day.
BHP figure is on the right middle (618 at the hubs)
Lb/ft is on the left middle (divided by Diff Ratio which is 4.111:1, giving about 475 lb/ft)
Its maxing out the injectors, so has been set back a little form this run
https://www.youtube.com/watch?v=oFH4mg3w_jg
Weather is looking like it might be dry, I can't wait for this Sunday !!!
Hiya All,
I've done a little write up of the work carried out at Abbey Motorsport.
Couple of videos of the car on the Dyno too...
http://www.theprojectmoff.co.uk/2-march-2014---off...
haha, thanks Timeeeeh
Hiya All,
I've done a little write up of the work carried out at Abbey Motorsport.
Couple of videos of the car on the Dyno too...
http://www.theprojectmoff.co.uk/2-march-2014---off...
Hiya All,
I've done a little write up of the work carried out at Abbey Motorsport.
Couple of videos of the car on the Dyno too...
http://www.theprojectmoff.co.uk/2-march-2014---off...
During one of the laps on the recent track day, I snapped a tie rod. Was pretty scary in the car, sounded much noisier than on the video !!!
https://www.youtube.com/watch?v=rgFvEw6WBpw&fe...
https://www.youtube.com/watch?v=rgFvEw6WBpw&fe...
More power isn't really needed at the mo, it is only RWD, so is a tad of a handful
During one of the laps on the recent track day, I snapped a tie rod. Was pretty scary in the car, sounded much noisier than on the video !!!
https://www.youtube.com/watch?v=rgFvEw6WBpw&fe...
During one of the laps on the recent track day, I snapped a tie rod. Was pretty scary in the car, sounded much noisier than on the video !!!
https://www.youtube.com/watch?v=rgFvEw6WBpw&fe...
Gassing Station | Readers' Cars | Top of Page | What's New | My Stuff