PDR glue recommendations/ samples?
Discussion
Hi I'm currently doing some DIY pulling of some relatively light but annoying damage and have some really flexible clear glue and seems way too pliable to get a good pull, mostly glue staying on the car in one piece - although maybe the cheap tab set/glue etc doesn't help.
Any glue recommends please? Anywhere that does 1 stick samples so maybe I can see how good impression they work for my requirement?
Cause was pulling into drive at an angle a bit tired after the grief of visiting family in care home
My other cars that foul my drive needed to be moved to get this one out, so other car pulled in front of drive but was overhanging our drop curve a little too far leading me to overcompensate the angle - I should have known better
Very slightly sideswipe the wall but enough to leave some dent/swipe marks.
I touched in the paint and tried acid etched so should be no change of rust at least.
Removed PPF for this as it was down on the front edge of the rear wing, replacement PPF seems to be very cheap which I can put back on when I'm reasonably happy.
I'd rather not just fill and paint, so might as well pull out as much as possible regardless how long it takes....
I think I need some darker coloured glue for some of these smallish dents ( even the stuff I've used from Aldi etc has been better in the past), black or blue glue sticks?
This clear is way to flex - even after leaving minutes, heating panel and cleaning everything.
Any glue recommends please? Anywhere that does 1 stick samples so maybe I can see how good impression they work for my requirement?
Cause was pulling into drive at an angle a bit tired after the grief of visiting family in care home
My other cars that foul my drive needed to be moved to get this one out, so other car pulled in front of drive but was overhanging our drop curve a little too far leading me to overcompensate the angle - I should have known better
Very slightly sideswipe the wall but enough to leave some dent/swipe marks.
I touched in the paint and tried acid etched so should be no change of rust at least.
Removed PPF for this as it was down on the front edge of the rear wing, replacement PPF seems to be very cheap which I can put back on when I'm reasonably happy.
I'd rather not just fill and paint, so might as well pull out as much as possible regardless how long it takes....
I think I need some darker coloured glue for some of these smallish dents ( even the stuff I've used from Aldi etc has been better in the past), black or blue glue sticks?
This clear is way to flex - even after leaving minutes, heating panel and cleaning everything.
KECO UK Flex Collision sticks are very good, but they are in packs of 10, just watch the size/diameter of your gun, a lot of proper PDR glue sticks are for the bigger 15mm glue guns and the cheap Chinese PDR sets are often the smaller glue guns, 10 or 12mm so the PDR sticks are too wide to fit the cheap kits.
Alternatively Gluegunsdirect.com do sticks filtered on diameter, they are also very good and ive had sample sticks off them in the past so you can get them in a smaller number.
Respectfully, is often not just the glue, you need alcohol spray to degrease first, then a hot air gun to heat the panel to low 20's, then let the glue flash off for 30 seconds, and even then you really only get one pull before it comes off. I can easily get through 50 pulls for a small dent and it's incredibly frustrating at times, don't believe the social media videos.
If it needs painting anyway my default as a bodyshop is simply grind it back and weld the pull tabs, accepting its going to get painted, this is so much quicker and moves the metal much better, meaning less filler, but obviously if you don't need to paint then of course PDR is a great tool to have.
Good luck, you will be fighting the weather this time of year, so lightly heat the panel first.
Alternatively Gluegunsdirect.com do sticks filtered on diameter, they are also very good and ive had sample sticks off them in the past so you can get them in a smaller number.
Respectfully, is often not just the glue, you need alcohol spray to degrease first, then a hot air gun to heat the panel to low 20's, then let the glue flash off for 30 seconds, and even then you really only get one pull before it comes off. I can easily get through 50 pulls for a small dent and it's incredibly frustrating at times, don't believe the social media videos.
If it needs painting anyway my default as a bodyshop is simply grind it back and weld the pull tabs, accepting its going to get painted, this is so much quicker and moves the metal much better, meaning less filler, but obviously if you don't need to paint then of course PDR is a great tool to have.
Good luck, you will be fighting the weather this time of year, so lightly heat the panel first.
I got black glue sticks for £2 for 50 off ebay and they are better than the clear ones for adhesion and harder.
However still struggling though to pull but there is quite a crease on the feature line so might have to relent on some weld-on pulls like you suggested !
You can't reach behind as there is a welded seam/ second skin so no chance I can see of pushing it out from behind?
Threw some wet on wet paint ( acid etch, base coat, and a little lacquer) just to get a better impression of the damage as it was a mess and a pic of the original damage



This is the really prominent dents that need pulling. The rest there are slight creasing where it also scratched the paint above.
There is PPF to be reapplied anyway, its top reference is about the alloy wheel centre point so this may cover a lot but I'd still prefer to try and pull it out flat as possible.

However still struggling though to pull but there is quite a crease on the feature line so might have to relent on some weld-on pulls like you suggested !
You can't reach behind as there is a welded seam/ second skin so no chance I can see of pushing it out from behind?
Threw some wet on wet paint ( acid etch, base coat, and a little lacquer) just to get a better impression of the damage as it was a mess and a pic of the original damage
This is the really prominent dents that need pulling. The rest there are slight creasing where it also scratched the paint above.
There is PPF to be reapplied anyway, its top reference is about the alloy wheel centre point so this may cover a lot but I'd still prefer to try and pull it out flat as possible.
Edited by daytonavrs on Saturday 31st October 14:14
Not meaning to undermine your skills, but you are setting yourself quite a challenge to pull that using PDR as a DIY project and not having access to things like a slide hammer etc?
That is probably a full days work for a professional PDR, thats if they can move the metal back to the body line. You often have to knock down the crown on the outside of the low to relieve enough tension in the metal for it to then move. While the tension is locked in the crown it wont pull. Does that make sense? So you are keeping the tension on the glue tab with one hand pulling it out, and then hammering the edge of the low with the other hand to relieve the tension.
Its how far you want to take it, but you aren't going to get it perfect, you would need to use a skim of filler to get the shape back exactly, then you are into painting the rear quarter panel.
I'm not sure if you are after advice, which would be take it to a bodyshop if you want it properly repaired, or how far you are looking to go DIY? You state you have used etch primer, base and lacquer already? You need to take lacquer to a panel edge to get a proper finish which means either painting the entire rear quarter, or at least going to a sharp swage line?
That is probably a full days work for a professional PDR, thats if they can move the metal back to the body line. You often have to knock down the crown on the outside of the low to relieve enough tension in the metal for it to then move. While the tension is locked in the crown it wont pull. Does that make sense? So you are keeping the tension on the glue tab with one hand pulling it out, and then hammering the edge of the low with the other hand to relieve the tension.
Its how far you want to take it, but you aren't going to get it perfect, you would need to use a skim of filler to get the shape back exactly, then you are into painting the rear quarter panel.
I'm not sure if you are after advice, which would be take it to a bodyshop if you want it properly repaired, or how far you are looking to go DIY? You state you have used etch primer, base and lacquer already? You need to take lacquer to a panel edge to get a proper finish which means either painting the entire rear quarter, or at least going to a sharp swage line?
DaveF-SkinnysAutos said:
Not meaning to undermine your skills, but you are setting yourself quite a challenge to pull that using PDR as a DIY project and not having access to things like a slide hammer etc?
That is probably a full days work for a professional PDR, thats if they can move the metal back to the body line. You often have to knock down the crown on the outside of the low to relieve enough tension in the metal for it to then move. While the tension is locked in the crown it wont pull. Does that make sense? So you are keeping the tension on the glue tab with one hand pulling it out, and then hammering the edge of the low with the other hand to relieve the tension.
Its how far you want to take it, but you aren't going to get it perfect, you would need to use a skim of filler to get the shape back exactly, then you are into painting the rear quarter panel.
I'm not sure if you are after advice, which would be take it to a bodyshop if you want it properly repaired, or how far you are looking to go DIY? You state you have used etch primer, base and lacquer already? You need to take lacquer to a panel edge to get a proper finish which means either painting the entire rear quarter, or at least going to a sharp swage line?
Yes that does make sense sorry, I haven't tried that yet but certainly I have seen that mentioned and I also would probably be best to get a line boardThat is probably a full days work for a professional PDR, thats if they can move the metal back to the body line. You often have to knock down the crown on the outside of the low to relieve enough tension in the metal for it to then move. While the tension is locked in the crown it wont pull. Does that make sense? So you are keeping the tension on the glue tab with one hand pulling it out, and then hammering the edge of the low with the other hand to relieve the tension.
Its how far you want to take it, but you aren't going to get it perfect, you would need to use a skim of filler to get the shape back exactly, then you are into painting the rear quarter panel.
I'm not sure if you are after advice, which would be take it to a bodyshop if you want it properly repaired, or how far you are looking to go DIY? You state you have used etch primer, base and lacquer already? You need to take lacquer to a panel edge to get a proper finish which means either painting the entire rear quarter, or at least going to a sharp swage line?
The paint was just a rough quick repair to both adhere the metal with acid etch and also some paint just to get a better view of the overall damage and much later on once cured - better pulling surface later perhaps once fully cured over time?
I do have a slide hammer for using with the PDR glue actually, have a quite a few cheap things I've bought from China including that but as you mentioned earlier probably requires a silly amount of pulls to make any difference and the crown ridge.
I think I would be all day in this cold though trying to shift on that feature line. No hurry anyway I'm not getting rid of this car if ever
I could also probably live with some imperfection, its only a car...I could perhaps look at pro repair but honestly with where I'm now at putting myself into early retirement/settlement with current employer as they are massively downsizing and I'm just feeling quite defeated with life and work.
I just like messing about trying to improve the damage almost more hobbyist
daytonavrs said:
Yes that does make sense sorry, I haven't tried that yet but certainly I have seen that mentioned and I also would probably be best to get a line board
The paint was just a rough quick repair to both adhere the metal with acid etch and also some paint just to get a better view of the overall damage and much later on once cured - better pulling surface later perhaps once fully cured over time?
I do have a slide hammer for using with the PDR glue actually, have a quite a few cheap things I've bought from China including that but as you mentioned earlier probably requires a silly amount of pulls to make any difference and the crown ridge.
I think I would be all day in this cold though trying to shift on that feature line. No hurry anyway I'm not getting rid of this car if ever
I could also probably live with some imperfection, its only a car...
I could perhaps look at pro repair but honestly with where I'm now at putting myself into early retirement/settlement with current employer as they are massively downsizing and I'm just feeling quite defeated with life and work.
I just like messing about trying to improve the damage almost more hobbyist
Perfect, and on a DIY basis if I can help just shout up, I run a bodyshop so happy to point you in the right direction, but on the understanding it's for DIY results! As its so low down and on a tight panel with body lines, I would recommend you save your money on a line board and just use your hand to feel for the shape, if it was on a flat panel then a line board would help you. Also, you are likely to pull off any new paint and it will be a worse surface to pull on, so for future reference you are a lot better off just cleaning with alcohol and if you need some clarity on the surface then polish the material thats there, new paint wont have bonded as well and will lift off with the tabs. The paint was just a rough quick repair to both adhere the metal with acid etch and also some paint just to get a better view of the overall damage and much later on once cured - better pulling surface later perhaps once fully cured over time?
I do have a slide hammer for using with the PDR glue actually, have a quite a few cheap things I've bought from China including that but as you mentioned earlier probably requires a silly amount of pulls to make any difference and the crown ridge.
I think I would be all day in this cold though trying to shift on that feature line. No hurry anyway I'm not getting rid of this car if ever
I could also probably live with some imperfection, its only a car...I could perhaps look at pro repair but honestly with where I'm now at putting myself into early retirement/settlement with current employer as they are massively downsizing and I'm just feeling quite defeated with life and work.
I just like messing about trying to improve the damage almost more hobbyist
Also you may be better using a bigger tab to get a better surface area, and over pulling it slightly, then knocking it back down. You will get to a point where you will likely have to accept its as good as its going to get, or go down the route of using filler to get the shape, and at that point you are into a whole different set of DIY skills!
Etch is correct for bare metal in these circs but wont give any build, so if you go with paint again try a high build primer after the etch to smooth things out. Finally, don't go wet on wet, you are risking reactions and shrinking back, just take your time and let each different material cure before applying the next.
It looks like you are having fun, and thats what life's about!
Ha fine with that thanks
This will just be my car for the good while.
Already modestly okay ( not overjoyed) with the paint for now, prob good until April odd time and I could look at it again paint wise.
The worst is building up and dent removal as you say, I can try and attack that over time and focus again like you said on the high point/crown and see if I can release some pressure and repeat pulls where it will become less noticeble
Even this on dmg back on the front rear arch isn't that bad really, hard to spot where it is esp in black - not prominent like on any doors somehow.
This will just be my car for the good while.
Already modestly okay ( not overjoyed) with the paint for now, prob good until April odd time and I could look at it again paint wise.
The worst is building up and dent removal as you say, I can try and attack that over time and focus again like you said on the high point/crown and see if I can release some pressure and repeat pulls where it will become less noticeble
Even this on dmg back on the front rear arch isn't that bad really, hard to spot where it is esp in black - not prominent like on any doors somehow.
It was barely any paint by the way, just because I'd sanded down to bare at some point with wet and dry to rough out the scratched area. e.g. 1.5cm long point 2-3mm wide and found it better to just use the aerosol nozzle to spray in over that rather than trying to apply with a artists brush
Then went over that with black then lacquer, doesn't seem to have distorted really but was barely any paint
It already looks 75% better on paint terms I think than before (to me), and can hold out for improvement as mentioned.
Regarding the 4th pic, generally if there's any paint damage then PDF won't work, or won't be tried - it pulls quite strongly on the paint and it would just flake the paint off.
For the glue you get in the cheap kits, it does kinda work, or can be made to work, but it has a narrow temperature window where it seems to best adhere in. So warm the panel up eg with a hairdryer and also use the biggest tab which you can, so the pull force can be greater before the glue fails. I don't know how the experts do it so well, whether its just skill or they have access to better glues etc.
For the glue you get in the cheap kits, it does kinda work, or can be made to work, but it has a narrow temperature window where it seems to best adhere in. So warm the panel up eg with a hairdryer and also use the biggest tab which you can, so the pull force can be greater before the glue fails. I don't know how the experts do it so well, whether its just skill or they have access to better glues etc.
I think I will just leave it for now as any attempt to pull it further as you both mentioned may pull the light paint repair off and I've touched it up to get over winter for now.
With the dark colour of the car and being so low down you would have to be looking for the damage too, so I'm not quite so emotive over it as I first was and happier to have touched over the scratches at least for now.
My only other idea was seeing if you could pry from behind / reverse from the inner skin given a second skin is in the way behind the wheel guard - but the drain holes are quite further along so not direct way to push anything up unfortunately.
I have a load of pry rods but absolutely no access to push out I can see yet.
Although I was thinking one alternative option might be to drill a small hole from underneath at the sill side for access and to plug/repair that later ( small enough to permit the small dent rods so way under 1cm) but I'm not rushing into that but anything like this is possible isn't it?
Thanks all for your support anyway. Might come back to this in the distant future, perhaps if I'm bored in improving weather to come when winter hopefully is a distant unpleasant memory
With the dark colour of the car and being so low down you would have to be looking for the damage too, so I'm not quite so emotive over it as I first was and happier to have touched over the scratches at least for now.
My only other idea was seeing if you could pry from behind / reverse from the inner skin given a second skin is in the way behind the wheel guard - but the drain holes are quite further along so not direct way to push anything up unfortunately.
I have a load of pry rods but absolutely no access to push out I can see yet.
Although I was thinking one alternative option might be to drill a small hole from underneath at the sill side for access and to plug/repair that later ( small enough to permit the small dent rods so way under 1cm) but I'm not rushing into that but anything like this is possible isn't it?
Thanks all for your support anyway. Might come back to this in the distant future, perhaps if I'm bored in improving weather to come when winter hopefully is a distant unpleasant memory

Gassing Station | Bodywork & Detailing | Top of Page | What's New | My Stuff


