Clear coat peeling
Discussion
Simple Q: what to do about this?

It looks to me like the clear coat is flaking off the colour coat. Can it be repaired? DIY or a chips away place? Or a body shop? The rest of the car isn't concourse standard, but I'd like it to look reasonable.
It's on an Elise, so fibreglass bodywork, but I don't think that's relevant.
All suggestions welcome, thanks.
It looks to me like the clear coat is flaking off the colour coat. Can it be repaired? DIY or a chips away place? Or a body shop? The rest of the car isn't concourse standard, but I'd like it to look reasonable.
It's on an Elise, so fibreglass bodywork, but I don't think that's relevant.
All suggestions welcome, thanks.
Hi,
Have you got a wider image of where it is on the overall panel?
Yes its lacquer peel, its usually caused by UV light, and is also way more common on red cars, its where the clearcoat has come away from the layer beneath.
There isnt really a DIY long term solution, the only way to properly deal with it is sand it back and apply a new clearcoat layer over the whole panel, hence me asking which panel it is on.
In theory, if there is a swage line, or shape change nearby you could take the edge of the clear to there, but really it needs to go to a panel edge or you are creating a weak edge further down the line which will lift again, but its your choice.
Have you got a wider image of where it is on the overall panel?
Yes its lacquer peel, its usually caused by UV light, and is also way more common on red cars, its where the clearcoat has come away from the layer beneath.
There isnt really a DIY long term solution, the only way to properly deal with it is sand it back and apply a new clearcoat layer over the whole panel, hence me asking which panel it is on.
In theory, if there is a swage line, or shape change nearby you could take the edge of the clear to there, but really it needs to go to a panel edge or you are creating a weak edge further down the line which will lift again, but its your choice.
Thanks Dave. That's helpful, even if it's not good news!
Here are some more photos.


I've drawn around the patch in question to show where it is. There's a lovely convenient edge just in front of the peeling bit but nowhere at all to lose a spray line behind it.
The paint on the rest of the car isn't great and I think it'll need some love at some point fairly soon. Perhaps I will bring that love forward and not bother patching this area.
Given the cost of everything these days and the fact that I have no money I'm wondering about a home respray. I guess you'll tell me that that's a daft idea ...
Here are some more photos.
I've drawn around the patch in question to show where it is. There's a lovely convenient edge just in front of the peeling bit but nowhere at all to lose a spray line behind it.
The paint on the rest of the car isn't great and I think it'll need some love at some point fairly soon. Perhaps I will bring that love forward and not bother patching this area.
Given the cost of everything these days and the fact that I have no money I'm wondering about a home respray. I guess you'll tell me that that's a daft idea ...

Thanks for the extra images, lovely car!
Unfortunately the only way to do that properly is to rub it back and apply a couple of coats of new lacquer, but that would need to cover the entire back end of the car, as thats a big old panel!
Its not doing any immediate harm as such, but its a sign that the clear is failing, so the patch will only get bigger over time.
A 'Smart' repair is when you keep the repair local and blend the clear coat, but on a massive flat panel like that it just wont work, wherever you tried to fade out the clear you will get a visible line which will look worse than the current problem, the only way to do it is to reclear the entire back end, sorry.
Could you live with some PPF type patches that covered it on both sides of the car maybe so it looked like a design to stop scratches getting in and out etc?
If you want to respray it yourself, then obviously thats a big job, and to honest if you don't have the kit it would probably cost you more in set up costs! Where are you in the UK? If you are near the Midlands I often offer that you can do the prep and I'll do the spraying to keep costs down.
Unfortunately the only way to do that properly is to rub it back and apply a couple of coats of new lacquer, but that would need to cover the entire back end of the car, as thats a big old panel!
Its not doing any immediate harm as such, but its a sign that the clear is failing, so the patch will only get bigger over time.
A 'Smart' repair is when you keep the repair local and blend the clear coat, but on a massive flat panel like that it just wont work, wherever you tried to fade out the clear you will get a visible line which will look worse than the current problem, the only way to do it is to reclear the entire back end, sorry.
Could you live with some PPF type patches that covered it on both sides of the car maybe so it looked like a design to stop scratches getting in and out etc?
If you want to respray it yourself, then obviously thats a big job, and to honest if you don't have the kit it would probably cost you more in set up costs! Where are you in the UK? If you are near the Midlands I often offer that you can do the prep and I'll do the spraying to keep costs down.
DaveF-SkinnysAutos said:
Thanks for the extra images, lovely car!
Unfortunately the only way to do that properly is to rub it back and apply a couple of coats of new lacquer, but that would need to cover the entire back end of the car, as thats a big old panel!
Its not doing any immediate harm as such, but its a sign that the clear is failing, so the patch will only get bigger over time.
A 'Smart' repair is when you keep the repair local and blend the clear coat, but on a massive flat panel like that it just wont work, wherever you tried to fade out the clear you will get a visible line which will look worse than the current problem, the only way to do it is to reclear the entire back end, sorry.
Could you live with some PPF type patches that covered it on both sides of the car maybe so it looked like a design to stop scratches getting in and out etc?
If you want to respray it yourself, then obviously thats a big job, and to honest if you don't have the kit it would probably cost you more in set up costs! Where are you in the UK? If you are near the Midlands I often offer that you can do the prep and I'll do the spraying to keep costs down.
That's quite a good idea as a temp fix. Possibly a triangular shape tapering off closer to the door seal.Unfortunately the only way to do that properly is to rub it back and apply a couple of coats of new lacquer, but that would need to cover the entire back end of the car, as thats a big old panel!
Its not doing any immediate harm as such, but its a sign that the clear is failing, so the patch will only get bigger over time.
A 'Smart' repair is when you keep the repair local and blend the clear coat, but on a massive flat panel like that it just wont work, wherever you tried to fade out the clear you will get a visible line which will look worse than the current problem, the only way to do it is to reclear the entire back end, sorry.
Could you live with some PPF type patches that covered it on both sides of the car maybe so it looked like a design to stop scratches getting in and out etc?
If you want to respray it yourself, then obviously thats a big job, and to honest if you don't have the kit it would probably cost you more in set up costs! Where are you in the UK? If you are near the Midlands I often offer that you can do the prep and I'll do the spraying to keep costs down.
Chaps,
Thanks for the answers. Belle427 - it is a summer car (and I declared it SORN as of a couple of days ago), but the paintwork is scruffy and hence I think something can and should be done about it. The bit in the picture is just where you see it every time you get into and out of it so it's hard to ignore!
Tabs, thanks. Yes, that's not a bad idea. I have a spray can of clear coat (which is probably utterly rubbish stuff) but I could dab some into the affected area with a small brush which would help.
DaveF, thanks again for your very comprehensive replies. A couple of coats of lacquer on the rear of the car is getting towards half a respray, and if I'm on the hook for half a respray then I might as well do the whole thing as the front ain't that pretty either ...
PPF type patches aren't a bad idea. I have some of the stuff which could be trimmed to the right shape. Thanks for the suggestion!
Home respray - thanks for your comments. Respraying a car is something which fascinates me and I'd love to have a go, but the (many) threads on here about it leave me half-keen and half-terrified. I have a compressor and a very cheap gun and am very happy spraying smaller things with one-pack paint but doing a whole car is a big step on from that. You suggestion that I could do the prep and you do the spraying is an interesting one. The Elise has front and rear clamshells which could be removed and prepped and I could drop them off to you fairly easily. I'm in Gloucestershire - where are you?
Thanks again.
Thanks for the answers. Belle427 - it is a summer car (and I declared it SORN as of a couple of days ago), but the paintwork is scruffy and hence I think something can and should be done about it. The bit in the picture is just where you see it every time you get into and out of it so it's hard to ignore!
Tabs, thanks. Yes, that's not a bad idea. I have a spray can of clear coat (which is probably utterly rubbish stuff) but I could dab some into the affected area with a small brush which would help.
DaveF, thanks again for your very comprehensive replies. A couple of coats of lacquer on the rear of the car is getting towards half a respray, and if I'm on the hook for half a respray then I might as well do the whole thing as the front ain't that pretty either ...
PPF type patches aren't a bad idea. I have some of the stuff which could be trimmed to the right shape. Thanks for the suggestion!
Home respray - thanks for your comments. Respraying a car is something which fascinates me and I'd love to have a go, but the (many) threads on here about it leave me half-keen and half-terrified. I have a compressor and a very cheap gun and am very happy spraying smaller things with one-pack paint but doing a whole car is a big step on from that. You suggestion that I could do the prep and you do the spraying is an interesting one. The Elise has front and rear clamshells which could be removed and prepped and I could drop them off to you fairly easily. I'm in Gloucestershire - where are you?
Thanks again.
2Btoo - I'm in Coventry - I'm sure you can find a bodyshop local that you can trust, but if I can help just PM me, or you will find my contact details online. I think some sort of PPF patch is the way forward, something that looks like it should be there and mirrored on the other side.
21TonyK - There are differences, but equally, painting is painting! The main reason is really that modern insurance bodyshops are just a conveyor belt of repairs, they bake everything to keep production turning over and you cant bake fibreglass, so those type of bodyshops firstly wouldn't want the work as it would slow the system down, and if they did, its outside their day to day work. The other difference is that it does react differently, so it flexes more, it absorbs heat and chemicals differently and it holds solvents for a lot, lot longer. So it just needs different materials and techniques, but not necessarily needing a specialist if its a simple repair. If it needs repairing ideally it needs a fibreglass product or at least one that will bond and flex. It needs longer for solvents to gas out, so primer needs longer to cure, and you need a lacquer with a long open window for the solvent to evaporate before it flashes over, but then that creates more chance of it running, unless you change your technique to compensate etc. Basically lots of small changes, but not rocket science.
21TonyK - There are differences, but equally, painting is painting! The main reason is really that modern insurance bodyshops are just a conveyor belt of repairs, they bake everything to keep production turning over and you cant bake fibreglass, so those type of bodyshops firstly wouldn't want the work as it would slow the system down, and if they did, its outside their day to day work. The other difference is that it does react differently, so it flexes more, it absorbs heat and chemicals differently and it holds solvents for a lot, lot longer. So it just needs different materials and techniques, but not necessarily needing a specialist if its a simple repair. If it needs repairing ideally it needs a fibreglass product or at least one that will bond and flex. It needs longer for solvents to gas out, so primer needs longer to cure, and you need a lacquer with a long open window for the solvent to evaporate before it flashes over, but then that creates more chance of it running, unless you change your technique to compensate etc. Basically lots of small changes, but not rocket science.
Thanks for the suggestions of a stone chip film patch over the affected area. I've done it, and it looks like this.

I think it's an improvement, but the edges of the missing clear coat show through a bit. I did try filling the hole with a bit of clear coat from a spray can (applied with a small brush) but it wasn't enough. I might buy some black film and see if that is any better; there is black film elsewhere on the car so it wouldn't look as out of place as it sounds.
I did one on the other side as well, to match. Here it is.

Again, this isn't perfect as I put it on a bit too far forwards and it doesn't quite stick at the front.
DaveF, thanks for your suggestion of spraying the panels if I was to do the prep work. I'm in Gloucestershire so a bit over an hour away. I'm quite interested but it would mean moving the clamshells around and I don't have a van to do this, plus I'd be nervous about moving newly painted panels to bring them home. Can you give me an idea of price for such a thing? Or would it be better if I was to PM you?
Thanks again.
I think it's an improvement, but the edges of the missing clear coat show through a bit. I did try filling the hole with a bit of clear coat from a spray can (applied with a small brush) but it wasn't enough. I might buy some black film and see if that is any better; there is black film elsewhere on the car so it wouldn't look as out of place as it sounds.
I did one on the other side as well, to match. Here it is.
Again, this isn't perfect as I put it on a bit too far forwards and it doesn't quite stick at the front.
DaveF, thanks for your suggestion of spraying the panels if I was to do the prep work. I'm in Gloucestershire so a bit over an hour away. I'm quite interested but it would mean moving the clamshells around and I don't have a van to do this, plus I'd be nervous about moving newly painted panels to bring them home. Can you give me an idea of price for such a thing? Or would it be better if I was to PM you?
Thanks again.
Yeah, just PM me, or google Skinny Autos and you will see my contact details, Im on here as a petrol head to offer advice and talk to others, not to sell my business, but happy to help even if its what to look for in a bodyshop local to you.
I was thinking more of a coloured PPF film, depending on your taste, so either red, or carbon fibre patterned, or black etc, something to cover it so it wasn't visible, but it depends on your tastes etc if that would be suitable.
I was thinking more of a coloured PPF film, depending on your taste, so either red, or carbon fibre patterned, or black etc, something to cover it so it wasn't visible, but it depends on your tastes etc if that would be suitable.
Gassing Station | Bodywork & Detailing | Top of Page | What's New | My Stuff


