Radiators re cores
Author
Discussion

Lotobear

Original Poster:

9,276 posts

159 months

Friday 30th October
quotequote all
I am looking for a firm to fit a new standard core into the radiator for my Elan. The radiator is essentially any early Spitfire rad, modded to suit the Lotus by turning around the inlet and outlet - its a simple affair.

I've been staggered by the cost quoted locally and would appreciate any recommendations on good traditional firms who can do this - preferably North West England or North East.

I recall the days when there was a Serck services in every town who would do a re core at a reasonable price but they all seem to have gone.

Heaveho

7,609 posts

205 months

Friday 30th October
quotequote all
Advanced radiators used to be in the West end of Newcastle but have moved to a unit in Washington. I used them to recore my Mk1 MR2 rad a few years ago, couple of hundred quid including fixing a couple of captive nuts that had come adrift.

RazerSauber

2,945 posts

91 months

Friday 30th October
quotequote all
I've heard good things about Desert Radiators in Widnes but never used them myself

Jap90s

2,041 posts

152 months

Friday 30th October
quotequote all
I've found similar - to re core a Bristol rad - it's not a complex operation

£1,000+ quotes

theadman

753 posts

188 months

Friday 30th October
quotequote all
Just a word of warning from my own experience.

Chasing an inexpensive recore can cost more than you think. Most cores are now made in China and many are made to a poor standard.

I went through two cores that didn't work as the water passages were too small. One of these was supplied by a well known company in the South West, so not a 'back street' outfit.

It's worth asking where the cores come from and if it's China, ask whether the company you are dealing with have them made to their own specification or take them off the shelf. Personally, I'd now avoid any Chinese core that is 'off the shelf'.

After my bad experience, I was told to speak to Radtec in Cannock who were brilliant. I've now bought two radiators from them and would recommend their products. A little bit more expensive maybe, but a whole lot better.

Hope that helps.

droopsnoot

14,792 posts

273 months

Saturday 31st October
quotequote all
I tried to get a radiator re-cored for one of my Vauxhalls, it would only have saved about £50 over having a new alloy radiator built from scratch using my old one as a pattern.

Maki65.

16 posts

12 months

Sunday 1st November
quotequote all
Are alloy radiators not more susceptible to damage from stones etc. This is what a radiator repairer told me last year.

e42

213 posts

219 months

Sunday 1st November
quotequote all
I used MRS Radiators in Preston to recore my Marcos radiator, excellent job.

Jap90s

2,041 posts

152 months

Sunday 1st November
quotequote all
Maki65. said:
Are alloy radiators not more susceptible to damage from stones etc. This is what a radiator repairer told me last year.
Probably 95% of radiators are alloy so I wouldn't worry

eliot

11,999 posts

285 months

Sunday 1st November
quotequote all
My go-to Kempston Radiators in bedford ceased trading (well stopped doing old-school rad repairs) - found these guys who repaired my Range Rover classic copper radiator (they are pretty big - they can fabricate ally rads if you want)

https://www.nargroup.com/

Lotobear

Original Poster:

9,276 posts

159 months

Monday 2nd November
quotequote all
Heaveho said:
Advanced radiators used to be in the West end of Newcastle but have moved to a unit in Washington. I used them to recore my Mk1 MR2 rad a few years ago, couple of hundred quid including fixing a couple of captive nuts that had come adrift.
Thanks for this - I've also had these guys recommended from a friend and they are reasonably handy for me so I will give them a go. He said the took over from Serck when they closed in Newcastle some years ago.

Lotobear

Original Poster:

9,276 posts

159 months

Monday 2nd November
quotequote all
e42 said:
I used MRS Radiators in Preston to recore my Marcos radiator, excellent job.
I've just spoken with Howard and what an impressive guy - he took time to explain what they do and that there is a price range based upon the quality of the core.

I will almost certainly go there.

Lotobear

Original Poster:

9,276 posts

159 months

Monday 2nd November
quotequote all
Lotobear said:
Heaveho said:
Advanced radiators used to be in the West end of Newcastle but have moved to a unit in Washington. I used them to recore my Mk1 MR2 rad a few years ago, couple of hundred quid including fixing a couple of captive nuts that had come adrift.
Thanks for this - I've also had these guys recommended from a friend and they are reasonably handy for me so I will give them a go. He said the took over from Serck when they closed in Newcastle some years ago.
Just spoken with them and it seems they have been taken over by a large firm and are now concentrating on large commercial heat transfer systems. He said he would get back to me with a price but to be honest he didn't sound too interested.

Heaveho

7,609 posts

205 months

Monday 2nd November
quotequote all
Lotobear said:
Lotobear said:
Heaveho said:
Advanced radiators used to be in the West end of Newcastle but have moved to a unit in Washington. I used them to recore my Mk1 MR2 rad a few years ago, couple of hundred quid including fixing a couple of captive nuts that had come adrift.
Thanks for this - I've also had these guys recommended from a friend and they are reasonably handy for me so I will give them a go. He said the took over from Serck when they closed in Newcastle some years ago.
Just spoken with them and it seems they have been taken over by a large firm and are now concentrating on large commercial heat transfer systems. He said he would get back to me with a price but to be honest he didn't sound too interested.
Hmm, that doesn't sound promising. Shame, the guy I dealt with when I got mine done was interested and knowledgeable. Hope you get sorted. Can you update the thread when you get it done, I'm in your area and will undoubtedly need a recommendation at some point.

Lotobear

Original Poster:

9,276 posts

159 months

Monday 2nd November
quotequote all
Heaveho said:
Lotobear said:
Lotobear said:
Heaveho said:
Advanced radiators used to be in the West end of Newcastle but have moved to a unit in Washington. I used them to recore my Mk1 MR2 rad a few years ago, couple of hundred quid including fixing a couple of captive nuts that had come adrift.
Thanks for this - I've also had these guys recommended from a friend and they are reasonably handy for me so I will give them a go. He said the took over from Serck when they closed in Newcastle some years ago.
Just spoken with them and it seems they have been taken over by a large firm and are now concentrating on large commercial heat transfer systems. He said he would get back to me with a price but to be honest he didn't sound too interested.
Hmm, that doesn't sound promising. Shame, the guy I dealt with when I got mine done was interested and knowledgeable. Hope you get sorted. Can you update the thread when you get it done, I'm in your area and will undoubtedly need a recommendation at some point.
This is them now, so unfortunately it doesn't look good for the odd classic car radiator job frown:

https://www.glacierenergy.com/

Skyedriver

23,717 posts

313 months

Monday 2nd November
quotequote all
Was going to suggest Advanced, but there was another think based Sandyford/Jesmond, Newcastle. Charlton Radiators, very attractive miniskirted lady used to drive for them, guess she'll be about 60 now. I remember Serck in Newastle backini the 80's
There used to be a place in Darlo, on the road into Morrisons, looked like an old Blacksmiths shop , they did radiators.
Phone numbers on the van on the left
Have you tried the usual Lotus specialists, SJ Lotus Bits etc

Edited by Skyedriver on Monday 2nd November 14:44

Skyedriver

23,717 posts

313 months

Monday 2nd November
quotequote all


Darlington Radiators, think they may be called "Clearflow" Maynell Road, off North Road

Escort3500

13,592 posts

176 months

Monday 2nd November
quotequote all
I’ve used Autocool Radiators in Scarborough for recoring two rads, and they were really good to deal with. Reasonably priced, prompt and good quality.


Decky_Q

2,109 posts

208 months

Monday 2nd November
quotequote all
Brownlow Radiators in Lurgan made me a cuprobronze brazed rad for my supercharged vx220. It was blowing the plastic end caps off the usual radiators, the one they made me was fantastic @£180 it was cheaper then the crappy GM ones.

Lotobear

Original Poster:

9,276 posts

159 months

Wednesday 4th November
quotequote all
I'm going withe MRS, speaking with the owner and then viewing this clinched it for me:

https://www.mrsheattransfer.com/remanufacture-of-a...