If the devil was a car part...
If the devil was a car part...
Author
Discussion

Ian974

Original Poster:

3,211 posts

230 months

Tuesday 12th July 2011
quotequote all
Just sick of these today

Designed and placed specifically so that you can't squeeze them by hand and when you use pliers they'll ping round 90 degrees so that you now cannot reach it with those either.
So guys, what is your most hated car part?

NiceCupOfTea

25,608 posts

282 months

Wednesday 13th July 2011
quotequote all
I don't mind those actually. The first time I dealt with them I made the same mistake and got one twisted at a silly angle so I couldn't get the molegrips on it (next to the engine block). That was a PITA.

I like them now because I don't have the constant "will it leak or will it sheer" quandary about doing up jubilee clips another turn...

EDLT

15,421 posts

237 months

Wednesday 13th July 2011
quotequote all


Not a sight I want to see, especially on Peugeots/Citreons where the drive shaft has a habit of falling out as soon as you undo the bottom ball joint (and dropping gear oil everywhere) grumpy

anonymous-user

85 months

Wednesday 13th July 2011
quotequote all
door panel/trim retaining clips



it's coming, its coming, a little more pressure, just a little more...poing...st, snapped the little fker off.

ceriw

1,117 posts

236 months

Wednesday 13th July 2011
quotequote all
it would have to be the bloody seatbelt reminder bongs/beeps/gongs/bells/chimes
and particularly the ones in some citroens that increase in decibels for every cm you drive... jesus.

anonymous-user

85 months

Wednesday 13th July 2011
quotequote all
The top dead centre sensor on the F4R Renault engine. Located underneath the very large intake manifold, half way down the engine and held on with a banana shaped bracket and two bolts which are entirely unsighted. It's almost certain you'll drop one of the bolts too which will mean taking the floor off the retrieve it mad

Piepiepie

1,347 posts

185 months

Wednesday 13th July 2011
quotequote all

MGZRod

8,176 posts

207 months

Wednesday 13th July 2011
quotequote all


ETA: just realised who the OP is, you'll feel my pain with this post Ian hehe

Edited by MGZRod on Wednesday 13th July 02:09

OdramaSwimLaden

1,971 posts

200 months

Wednesday 13th July 2011
quotequote all
Brake bleed nipples / screws. fking horrible little ing bds!!


rockandrollmark

1,181 posts

254 months

Wednesday 13th July 2011
quotequote all
The fuel gauge

BDR529

3,560 posts

205 months

Wednesday 13th July 2011
quotequote all
yellowbentines said:
door panel/trim retaining clips



it's coming, its coming, a little more pressure, just a little more...poing...st, snapped the little fker off.
This!

obscene

5,180 posts

216 months

Wednesday 13th July 2011
quotequote all
MGZRod said:
rofl

Perfect with that username and the car you own. thumbup

chevy-stu

5,392 posts

259 months

Wednesday 13th July 2011
quotequote all


(must point out, pic is not my car..)

Baryonyx

18,297 posts

190 months

Wednesday 13th July 2011
quotequote all
The electronic throttle module in Volvo S60s. Most of them fail before 100,000 miles. Mine did. Replaced now though and fingers crossed I'll get another 65,000 miles out of it!

N5 NRO

258 posts

187 months

Wednesday 13th July 2011
quotequote all
The coolant pipes on a MKII Toyota MR2 which wrap around most of the engine and are attached to almost a dozen pipes using the clips mentioned in the OP. I eventually gave up and used a hacksaw to remove them, but not after many cuts, bruising and a hell of a lot of swearing.

clonmult

10,529 posts

240 months

Wednesday 13th July 2011
quotequote all
BDR529 said:
yellowbentines said:
door panel/trim retaining clips



it's coming, its coming, a little more pressure, just a little more...poing...st, snapped the little fker off.
This!
Damn near every car ever made seems to have several of these, stupidly designed, always break. Very definitely the devils work.

KP328

1,879 posts

226 months

Wednesday 13th July 2011
quotequote all

Mini balljoint, they usually pop off with a bit of heat, not this one.

mat205125

17,790 posts

244 months

Wednesday 13th July 2011
quotequote all
Ian974 said:
Just sick of these today

Designed and placed specifically so that you can't squeeze them by hand and when you use pliers they'll ping round 90 degrees so that you now cannot reach it with those either.
So guys, what is your most hated car part?
I'll agree that a good old jubilee clip with hex/screw tightening is much preferable, HOWEVER I'd take these type of clips ever single time compared to the modern machine fitted / crimp clips that we get on every hose these days, where you often have to destroy them to get them off, and then replace with a jubilee.


Hot Dog Harrigan

3,762 posts

249 months

Wednesday 13th July 2011
quotequote all
Ian974 said:
Just sick of these today

Designed and placed specifically so that you can't squeeze them by hand and when you use pliers they'll ping round 90 degrees so that you now cannot reach it with those either.
So guys, what is your most hated car part?




The right tools for the right job. smile

falkster

4,258 posts

234 months

Wednesday 13th July 2011
quotequote all
An intermittent crank position sensor!!