My Little '65 Pony
Author
Discussion

Kobra

Original Poster:

61 posts

212 months

Friday 30th October
quotequote all
Big Project. More info, soon come.

Edited by Kobra on Saturday 31st October 18:43


Edited by Kobra on Saturday 31st October 18:46


Edited by Kobra on Sunday 1st November 13:26


So, The Parts.

ARP bolts all round
Autolite spark plugs
CA complete engine wiring plus some other useful trinkets around the car
Canton Racing girdle for the main caps
COMP Cams engine finishing kit (all sorts of plugs etc.)
Dura-Bond cam bearings
Eaton Truetrac limited slip differential, this is a smart piece of purely mechanical gear. It can function perfectly as a diff. but once you floor it, it's on full-lock.
Edelbrock cylinder heads, valve covers, intake manifold, Pro-Flo 4 electronic fuel injection (straight-to-port)
Fel-Pro gasket kit
Fram oil filter
Hedman Hedders need no explaining, I went with the long ones
Howards Cams cam & lifters, screamer, not a torquer
Melling pushrods
Melling freeze plugs
Milodon high volume, high pressure oil pump
Motion Pro timing degree wheel
Motorad coolant fluid sensor
PRW billet main caps
Scorpion Racing rocker arms, full roller
Scott Drake GT style rear valance, shoots the pipes straight through, as opposed the exhaust pipes going under the bodywork. Only, I'm going to cut the pipes and paint 'em, black. This will give the appearance of the the exhausts being a part of the bodywork.
Scott Drake slip yoke which attaches to the gearbox---this is the bit that started the whole project when it blew itself onto the road.
Summit Racing timing gears and double chain
Thermo-Tec thermal wraps dipped in copper---not sure about the effectiveness but the headers should look cool wrapped in this.
Trick Flow valve cover breathers
Two Guys aka The Boys at the Garage with their Bespoke Works & Billet Parts---because virtually nothing that is supposed to fit, as in "bolt-on" almost never does.
LPS Performance / Lensu Power Shop, bespoke aluminum bellhousing
ZFd 6-speed manual transmission and clutch, should be able to handle 1,000 Nm, whatever that is in UK-ian, 800 lbs per sq. foot, roughly?
ChuSyyRay (China) LED headlights
Magnaflow stainless steel exhaust
MSD coil
Speed Hut (China) Gauges
Summit Racing 100 Amp alternator
Rotating assembly and internal balancing by Shafiroff, NY.
Lunati Sportsman Series 4340 Forged Steel Crank
Molnar 4340 H-Beam Forged Steel Rods w/ARP 2000 Bolts
Mahle Custom Coated Forged Aluminum Pistons
Plasma 1.5/1.5/3.0mm Moly Ring Set
Clevite 77 "H" Series Main & Rod Bearings
Factory Pin Fitted Rods & Pistons
Internally Balanced



Edited by Kobra on Sunday 1st November 14:00


Edited by Kobra on Monday 2nd November 16:02


Edited by Kobra on Tuesday 3rd November 15:27

SlimJim16v

8,242 posts

174 months

Friday 30th October
quotequote all
Very nice, the best Mustang. There are so many aftermarket parts you could spend a fortune.

Kobra

Original Poster:

61 posts

212 months

Saturday 31st October
quotequote all
SlimJim16v said:
Very nice, the best Mustang. There are so many aftermarket parts you could spend a fortune.
Thank you! I obviously feel the same way because I pulled the trigger on this beauty the minute I got the chance to do so, some 5 years ago.
Oh, yes, and I have spent a fortune on parts already! I'll put up a list of the parts and their makers shortly and you will find it ridiculous. Remember the scene in "The Good, the Bad, the Ugly" when Tuco (the Ugly) goes pistol shopping? That's me and the mechanic picking parts for the engine and the power delivery.

SlimJim16v

8,242 posts

174 months

Monday 2nd November
quotequote all
That's a lot of expensive sounding parts. More photos please.