Tuscan Custom LCD Screen and New Circuit board
Tuscan Custom LCD Screen and New Circuit board
Author
Discussion

czwalga

Original Poster:

12 posts

16 months

Saturday
quotequote all
I imported a tuscan to the USA last year. One of my annoyances was the LCD display barely worked. Even if working, not great in the sun.

I decided to develop a complete replacement. When through a few iterations and logged the car. Developed a simulator to run the dash on the bench to collect all the information I need. I'm not finished with it, but I have all of the mechanical, screen, and PCBs worked out so far.

I'm going to start working on the the firmware, so I'm open to some suggestions for improvements. The microcontroller has full access to any of the input data. So pretty much anything can be displayed in bright graphics.

It includes a new screen, display PCB board, Main PCB. I eliminates 3 of the PCBs within the gauge cluster, but retains the use of the outer one. It mates directly and just plugs in to the front LED boards and the outer interface PCB.

New Features:
1. Speedo Calibration. They'll be a calibration section which you can just hit drive to 40mph via your GPS on your phone, hit a button on the car and it'll calibrate your speedometer perfectly. Will work with any wheel size.

2. Much louder use of the speaker range. I'm not sure if it was just mine or everyones, but the speaker was woefully underutilized.

3. Option for up to 7 tach LEDs, will work with the OEM setup or you can add 7 leds and have a full racing style tach.

4. Smooth stepping option. The TVR quark is the gauges click, the gauge will be able to retain the OEM or go to a smooth control like most vehicles. My personal preference is the leave the Speedo click, but coolant and fuel to be smooth stepping. The OEM hysteresis is annoying with it flipping back and forth between two steps.

5. It will be a full color high brightness screen, 320x240 pixels. Dual brightness setting so high brightness during the day and lower when the lights are on so you're not blinded.

6. I'll have some base firmware that matches OEM then my design with the modern display, but will make the firmware open source if I end up selling them in which people could customize their own display and screens. This isn't a money making venture, but I've designed and built it as if I will sell it eventually.


Anyways, feel free to add any ideas or such that I'm missing.



Here's the simulator which i can control all the values. This is the main circuit board, I just finished it after a ton of development time. Ill have more updates over the next few weeks/months.












Edited by czwalga on Saturday 14th November 16:26

porterpainter

864 posts

68 months

Saturday
quotequote all
No suggestions to add, but this looks great!

blueg33

46,972 posts

255 months

I am in awe

Basil Brush

5,640 posts

294 months

blueg33 said:
I am in awe
+1. I wish I knew how to just start something like this!

TuscanS_DE

12 posts

13 months

Yesterday (11:42)
quotequote all
This looks brilliant, and the speedo calibration and day/night brightness alone would sell it to me.

One suggestion while you're still at the firmware stage: an external data connector. Even a small CAN port (500 kbit/s) or a plain serial port, with a published list of messages, would open it up to other projects.

I'm working on an electronics hub for my Tuscan S (Speed Six) that sits where the door ECUs live. It reads the engine ECU over the diagnostic plug and has a CAN bus for add-on sensors. With a port on your board:
- your dash could share what it already reads (fuel level, oil temp, oil pressure, speed), so other modules don't need to tap the same wires again
- the dash could show things it can't see itself: ECU faults, gear, fuel range/consumption, warnings via your louder speaker

If you're open to it, I'm happy to help define a simple message list both ways and test on a Speed Six. Either way, great work!