Headlight condensation
Discussion
A known fault on the F10 it appears
Last year it had mild cloudiness, and I wasn t too fussed to sort. This year it is noticeably worse and I m led to believe is only a matter of time before the water starts to cause wider issues/failure.
Pics below for illustration..
Anyone have any advice? Is it a case of DIY solution, send it off for fixing or buy a replacement (seem quite spenny).
Car is a 2014 530d.



Thanks all,
Last year it had mild cloudiness, and I wasn t too fussed to sort. This year it is noticeably worse and I m led to believe is only a matter of time before the water starts to cause wider issues/failure.
Pics below for illustration..
Anyone have any advice? Is it a case of DIY solution, send it off for fixing or buy a replacement (seem quite spenny).
Car is a 2014 530d.
Thanks all,
Edited by CTO on Sunday 25th October 14:09
Timms BMW Repairs and Information channel on YouTube has some good ideas on this. It boils down to basically a hairdryer and a pipe into the headlight until *bone* dry. Not at desk so can’t find the video but if you also check his site he has a picture of his E63 and a direct link to the video over the headlight. Much of a muchness.
Ps: spenny, ghastly word
Ps: spenny, ghastly word

The hairdryer/desiccant fix only works if the cause of the condensation is fixed.
So if there's a crack in the sealant fixing the front of the headlight to the rear housing, then you will just get more condensation. There are also seals between the modules on the back/top/bottom of the housing which when torn/damaged can also cause condensation.
BMW Warranty / BMW Insured Warranty are very inconsistent on whether they cover this seal failure or not...and it seems to come down to how much a dealer has claimed on warranty (i.e. are they too keen to put warranty claims in?).
BMW will only sell you a completely new, whole unit...and in the case of my LED lights on the LCI F31, they wanted £2000+ to supply & fit.
I've just left it for now, as it comes and goes - and strangely there doesn't seem to be a correlation between wet weather and condensation, nor big temp differences between day & night. If I ultimately come into a small lottery win, I will buy a genuine BMW/Hella part from one of the online sellers for about 50% of what the dealer wants.
On a good day, mine looks like this...

On a another day it can look like this...

...and on a bad day it can look like this...

So if there's a crack in the sealant fixing the front of the headlight to the rear housing, then you will just get more condensation. There are also seals between the modules on the back/top/bottom of the housing which when torn/damaged can also cause condensation.
BMW Warranty / BMW Insured Warranty are very inconsistent on whether they cover this seal failure or not...and it seems to come down to how much a dealer has claimed on warranty (i.e. are they too keen to put warranty claims in?).
BMW will only sell you a completely new, whole unit...and in the case of my LED lights on the LCI F31, they wanted £2000+ to supply & fit.
I've just left it for now, as it comes and goes - and strangely there doesn't seem to be a correlation between wet weather and condensation, nor big temp differences between day & night. If I ultimately come into a small lottery win, I will buy a genuine BMW/Hella part from one of the online sellers for about 50% of what the dealer wants.
On a good day, mine looks like this...
On a another day it can look like this...
...and on a bad day it can look like this...
Edited by mmm-five on Sunday 25th October 15:07
Thanks all,
So the options are
Split them and reseal.
Remove them and send them somewhere for someone else to do a better job than I will on the above..
Remove (I assume) and drill some teeny holes in the back, at the bottom.
Get a replacement from a breaker that may have the same issue.
Get rinsed by BMW…
Is there a breather pipe or similar that I should be checking?
So the options are
Split them and reseal.
Remove them and send them somewhere for someone else to do a better job than I will on the above..
Remove (I assume) and drill some teeny holes in the back, at the bottom.
Get a replacement from a breaker that may have the same issue.
Get rinsed by BMW…
Is there a breather pipe or similar that I should be checking?
Had this with my FiLs F10 530d - sorted it by drying them out completely overnight on a radiator on low; used a very thin bead of silicone sealant across the original seal line, pushed in and spread for good coverage, and then in the main cap; taped a bag of silica gel which was swapped out every 2-3 weeks for a few months.
The condensation never came back and they were spot on for a good 6 months before he sold it on
The condensation never came back and they were spot on for a good 6 months before he sold it on
CTO said:
Is there a breather pipe or similar that I should be checking?
Yeah, at least there was on the same age of 6 series I had with the same issue; there was a small rubber pipe/grommet on the back of the headlight that I pulled off and the headlight/misting dried out within 24 hours; I put it back on the next day and I never had the issue again. My only guess, was that there was some blockage in pipe preventing moisture/air from venting, but I couldn't see anything.If there is a pool of water in the headlight, that's a different story; ideal solution is to unbolt it if you have the tools to do so, drain it out and make sure to dry it out completely - ideally by leaving it in the house overnight in a warm room. Using a hairdryer is fighting an uphill battle as the hot air often just produces more moisture. Drilling a small hole in the bottom of the headlight is a last resort IMO.
Further to all of the above.
I’ve booked it in to have sorted.
https://www.keepyourcarsafe.co.uk/products/f10-f11...
These guys are about a 40 minute drive from me. ^^
I figure it’s likely to only cost more money if I don’t, and it’s not the weather for me to go faffing about on the drive and likely making things worse.
I’ll report back once completed. Might be a useful resource for fellow owners as the water ingress thing is very much a thing it appears for the F10!
Reviews look solid and they’ve been very helpful to deal with this eve.
Thanks all.

I’ve booked it in to have sorted.
https://www.keepyourcarsafe.co.uk/products/f10-f11...
These guys are about a 40 minute drive from me. ^^
I figure it’s likely to only cost more money if I don’t, and it’s not the weather for me to go faffing about on the drive and likely making things worse.
I’ll report back once completed. Might be a useful resource for fellow owners as the water ingress thing is very much a thing it appears for the F10!
Reviews look solid and they’ve been very helpful to deal with this eve.
Thanks all.
HI
I obtained this site from another forum
https://homeofheadlights.co.uk/products/bmw-f06-f1...
Maybe be useful
Trevor
I obtained this site from another forum
https://homeofheadlights.co.uk/products/bmw-f06-f1...
Maybe be useful
Trevor
On my F11 I had failures of the headlight Angel Eyes caused by "condensation" eventually getting to the control circuit board. The issue on mine was the cover on the back came loose and fell off. Worth a quick check first and make sure they are water tight. Yes dry out if wet, its a Jag trick to open up the sealed unit and allow the light to breathe. If maklng a hole below make sure its not in line with water thrown up.
CTO said:
Thanks all,
So the options are
Split them and reseal.
Remove them and send them somewhere for someone else to do a better job than I will on the above..
Remove (I assume) and drill some teeny holes in the back, at the bottom.
Get a replacement from a breaker that may have the same issue.
Get rinsed by BMW
Is there a breather pipe or similar that I should be checking?
Nope. Completely sealed. So the options are
Split them and reseal.
Remove them and send them somewhere for someone else to do a better job than I will on the above..
Remove (I assume) and drill some teeny holes in the back, at the bottom.
Get a replacement from a breaker that may have the same issue.
Get rinsed by BMW
Is there a breather pipe or similar that I should be checking?
Personally I wouldn't be drilling holes in £2000 headlights. Well, the LEDs are that much, not sure about the Xenons. Some 80s/90s Dad hacks are best avoided on modern stuff.
If you really must vent the headlight enclosure, you'd be better off with a length of hose with a filter on the end, similar to gearbox breathers.
It's possible one or more of the DRL module seals has shrunk, which is what happened to mine. Clear signs of the white crusties beyond the seal boundary and starting to corrode the module electronics. The seals are crap. Cheap foam rubber that crushes, stays crushed, then shrinks.
Only the main module has a proper O ring and never leaks.
It's pretty rare for the butyl bonding on the lense to fail, but that's all those headlight repairers do. Hairdryer and a fresh roll of butyl. Anyone can do it.
Hi all,
By way of closure on this one, and my thanks to all of you who have commented and added advice. DIY or otherwise
I opted to go and take it to the guys I mentioned in my past above; KYCS in Oldbury. They are only about 45 mins from me, and I got the opportunity to hole up in the local Spoons, drink bottomless coffee and watch the locals smashing back pints from 10AM onwards.
Drivers side headlight has now been replaced with a refurbished OEM BMW one.
Some oddities uncovered, such as my TMS module in the leaky one being aftermarket and not of any type they have ever seen before (it wouldn t let them bench test it and would only work on the car). They also pointed out that the passenger headlight is not OEM. It is Hella, so kind of, but not the original.
All of the above was news to me, and I can t say I m particularly impressed by the discovery. I have my suspicions about how some of these rather questionable components came to be fitted, although that s all they are, suspicions. I ll leave it at that
Anyhow: moving on, the service from KYCS today was excellent, and in the run up to organising the appt. I had a WhatsApp chat with the boss Simon via WhatsApp, and then today was very well looked after by a couple of guys called Joe and Ali.
They also let me have a look round their workshop. They had a lovely sunburst orange 640 in having some work down, plus it s an Aladdin cave of Gucci parts and upgrades.
Think I paid around £400. £75 of which was the removal and refitting. So it could be done cheaper if one can be arsed removing the headlight at home and taking it/posting it to them.
Done in two hours, including a conference call part way through to talk me through their findings and impressively offer the option of a significantly reduced price as the issue was linked to the fitment of the modules rather than the sealant failing. (The sealant was on its way out anyway so I just said get it done in one and I can forget about it)
Work comes with a two year warranty.
Before


And after


Job jobbed.
Disclaimer: I am not in any way affiliated with KYCS and neither did I receive a kickback for offering a decent review. I may also have explained some of their findings incorrectly, as I am a dullard.
Those of you that know me from the DIY house build will know how much jip I had with decent businesses and tradespeople, so if I have a good recommendation, I will always pass it on to help others like me out!

Cheers all
By way of closure on this one, and my thanks to all of you who have commented and added advice. DIY or otherwise

I opted to go and take it to the guys I mentioned in my past above; KYCS in Oldbury. They are only about 45 mins from me, and I got the opportunity to hole up in the local Spoons, drink bottomless coffee and watch the locals smashing back pints from 10AM onwards.
Drivers side headlight has now been replaced with a refurbished OEM BMW one.
Some oddities uncovered, such as my TMS module in the leaky one being aftermarket and not of any type they have ever seen before (it wouldn t let them bench test it and would only work on the car). They also pointed out that the passenger headlight is not OEM. It is Hella, so kind of, but not the original.
All of the above was news to me, and I can t say I m particularly impressed by the discovery. I have my suspicions about how some of these rather questionable components came to be fitted, although that s all they are, suspicions. I ll leave it at that

Anyhow: moving on, the service from KYCS today was excellent, and in the run up to organising the appt. I had a WhatsApp chat with the boss Simon via WhatsApp, and then today was very well looked after by a couple of guys called Joe and Ali.
They also let me have a look round their workshop. They had a lovely sunburst orange 640 in having some work down, plus it s an Aladdin cave of Gucci parts and upgrades.
Think I paid around £400. £75 of which was the removal and refitting. So it could be done cheaper if one can be arsed removing the headlight at home and taking it/posting it to them.
Done in two hours, including a conference call part way through to talk me through their findings and impressively offer the option of a significantly reduced price as the issue was linked to the fitment of the modules rather than the sealant failing. (The sealant was on its way out anyway so I just said get it done in one and I can forget about it)
Work comes with a two year warranty.
Before
And after
Job jobbed.
Disclaimer: I am not in any way affiliated with KYCS and neither did I receive a kickback for offering a decent review. I may also have explained some of their findings incorrectly, as I am a dullard.

Those of you that know me from the DIY house build will know how much jip I had with decent businesses and tradespeople, so if I have a good recommendation, I will always pass it on to help others like me out!
Cheers all
Edited by CTO on Wednesday 4th November 20:00
Gassing Station | BMW General | Top of Page | What's New | My Stuff


