BMW F34 330d Rear driveshaft removal for wheel bearing repla
Discussion
Hi everyone,
I'm currently replacing a rear wheel bearing on my 2014 BMW series 3 GT (F34) and have run into a problem getting the driveshaft out of the wheel hub.
So far, we've removed the brake disc, caliper and wheel hub flange. The old bearing has separated (wasn't actually that bad to get off), leaving the ball bearings exposed (see attached photo).
The problem is getting the driveshaft out of the remaining bearing assembly.
What we've found:
I thought the driveshaft was bolted on but I think for the F34 its some simple push mechanism?
The driveshaft can be pushed inwards approximately 2 cm through the bearing by hand, I could maybe push it more but I don't want to bust anything.
Will I be able to push the driveshaft through W, or will I need to remove the hub to get more clearance?
I couldn't remember how upload an image on onto the post so I've linked below

I'm currently replacing a rear wheel bearing on my 2014 BMW series 3 GT (F34) and have run into a problem getting the driveshaft out of the wheel hub.
So far, we've removed the brake disc, caliper and wheel hub flange. The old bearing has separated (wasn't actually that bad to get off), leaving the ball bearings exposed (see attached photo).
The problem is getting the driveshaft out of the remaining bearing assembly.
What we've found:
I thought the driveshaft was bolted on but I think for the F34 its some simple push mechanism?
The driveshaft can be pushed inwards approximately 2 cm through the bearing by hand, I could maybe push it more but I don't want to bust anything.
Will I be able to push the driveshaft through W, or will I need to remove the hub to get more clearance?
I couldn't remember how upload an image on onto the post so I've linked below
So for the F34 I didn't need to disconnect from the dif, we just removed enough bolts on the hub assembly to pivot it and allow space to lower the shaft out the way.
We've got the new bearing pressed in now, and we've pressed the hub back in.
Main issue we have now is that the shaft feels a little short and we can't get enough shaft to get the nut back on.
Weirdly the inner shaft is bumping up to the inner wheel bearing , so it looks like the shaft can't come through anymore, yet it still looks about 1cm too short at the front? Super odd.
My theories are:
1) Shaft is somehow short somewhere?
2) Hub isn't fully pressed back into the bearing?



We've got the new bearing pressed in now, and we've pressed the hub back in.
Main issue we have now is that the shaft feels a little short and we can't get enough shaft to get the nut back on.
Weirdly the inner shaft is bumping up to the inner wheel bearing , so it looks like the shaft can't come through anymore, yet it still looks about 1cm too short at the front? Super odd.
My theories are:
1) Shaft is somehow short somewhere?
2) Hub isn't fully pressed back into the bearing?
Don't force the shaft through the new bearing if it's shouldering on the inner side. A 10 mm shortfall is a lot, and hammering it will bruise the new race.
I'd compare the assembled hub and bearing stack with the other side first. If the hub flange isn't fully home in the inner race, the whole lot sits too far outboard and the shaft looks short, which matches what you're seeing. Same if the bearing isn't fully seated against the housing shoulder, or the circlip isn't fully in its groove.
Also check the inner CV hasn't started to separate or isn't fully plunged. If the inboard joint has dropped out a fraction, the shaft will genuinely be short even with a correctly seated hub. Once those are right, you can usually gain the last bit of thread by compressing the inner joint. Compare thread engagement with the opposite side, and confirm the replacement bearing is the correct width for the F34.
I'd compare the assembled hub and bearing stack with the other side first. If the hub flange isn't fully home in the inner race, the whole lot sits too far outboard and the shaft looks short, which matches what you're seeing. Same if the bearing isn't fully seated against the housing shoulder, or the circlip isn't fully in its groove.
Also check the inner CV hasn't started to separate or isn't fully plunged. If the inboard joint has dropped out a fraction, the shaft will genuinely be short even with a correctly seated hub. Once those are right, you can usually gain the last bit of thread by compressing the inner joint. Compare thread engagement with the opposite side, and confirm the replacement bearing is the correct width for the F34.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


