BMW N57 Cylinder Numbering?
Discussion
Does anyone know whether cylinder number 1 is at the front or towards the rear of a car with an N57 engine? The internet is conflicted on this, confusion associated with the fact that the timing chain is on the rear of the engine. Please only answer if you know for certain.
I need to change injector no. 5 and would like not to change injector no. 2 by mistake!
I need to change injector no. 5 and would like not to change injector no. 2 by mistake!
rOB.bOb said:
Does anyone know whether cylinder number 1 is at the front or towards the rear of a car with an N57 engine? The internet is conflicted on this, confusion associated with the fact that the timing chain is on the rear of the engine. Please only answer if you know for certain.
I need to change injector no. 5 and would like not to change injector no. 2 by mistake!
Cylinder 1 is at the front.I need to change injector no. 5 and would like not to change injector no. 2 by mistake!
For example, TIS shows this picture showing cylinder #1... and that's the front of the engine, as no sprockets.
I really need to get a copy of the workshop manual but I don't have time before I need to change an injector out this weekend.
Each injector is held in place by a "clamping jaw" which itself is secured by a single bolt. I think as this bolt tightens, it crushes a copper gasket ring at the base of the injector. If it's not tight enough, gases will leak out of the cylinder, too tight and maybe the bolt will strip the thread in the alloy head. I have a new bolt and gasket ring but I can't find a consistent torque specification on the internet.
I think initial torque is 8Nm then final torque is 26Nm but some sources say just 10Nm and some say 13Nm.
Does anyone know for sure? Thanks for any help.
Each injector is held in place by a "clamping jaw" which itself is secured by a single bolt. I think as this bolt tightens, it crushes a copper gasket ring at the base of the injector. If it's not tight enough, gases will leak out of the cylinder, too tight and maybe the bolt will strip the thread in the alloy head. I have a new bolt and gasket ring but I can't find a consistent torque specification on the internet.
I think initial torque is 8Nm then final torque is 26Nm but some sources say just 10Nm and some say 13Nm.
Does anyone know for sure? Thanks for any help.
The first (no.1) cylinder is always the one furthest from the output to the transmission.
Subsequent numbering can be a bit confusing on V engines, however, because manufacturers have different conventions for the second cylinder. The second cylinder could proceed along the same bank as No.1 or be on the front of the other bank.
Subsequent numbering can be a bit confusing on V engines, however, because manufacturers have different conventions for the second cylinder. The second cylinder could proceed along the same bank as No.1 or be on the front of the other bank.
rOB.bOb said:
I have a new bolt and gasket ring but I can't find a consistent torque specification on the internet.
I think initial torque is 8Nm then final torque is 26Nm but some sources say just 10Nm and some say 13Nm.
8nm and then 26nm.I think initial torque is 8Nm then final torque is 26Nm but some sources say just 10Nm and some say 13Nm.
Make sure head/injector mating face is clean (use seat cutter if required) and consider using heat-resistant grease (e.g. ceratec) on injector body to help next person. Replacement injector requires coding.
I don't think the bolt has to replaced as it's not a torque-to-angle specification, I've re-used without issues. But it can't hurt if you have one.
Thank you everyone for all your help and advice.
The car is abandoned 150 miles away after it went into limp mode and codes said a bad injector on cylinder 5. I'm collecting all parts, tools (including slide-hammer, ceramic grease, foxwell nt530 for coding) and information for a repair and recovery at the weekend. I could possibly have driven it home but I don't think the engine vibrations would have been great on an engine where the crank-bearings and timing chain are known to be delicate.
The car is abandoned 150 miles away after it went into limp mode and codes said a bad injector on cylinder 5. I'm collecting all parts, tools (including slide-hammer, ceramic grease, foxwell nt530 for coding) and information for a repair and recovery at the weekend. I could possibly have driven it home but I don't think the engine vibrations would have been great on an engine where the crank-bearings and timing chain are known to be delicate.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


