BMW 1 series traction control / ABS sensor
BMW 1 series traction control / ABS sensor
Author
Discussion

EllzJ

Original Poster:

6 posts

72 months

Wednesday 11th November 2020
quotequote all
Hello all,

My BMW 118d has unfortunately developed the traction control / ABS warning light problem.

I understand this can be fixed my replacing the reluctor ring and ABS sensor.

I have read the code which indicates it is the rear right wheel with the problem.

I’ve called a few garages, however they’ve quoted over £400 to replace the ring and sensor.

I have ordered the reluctor ring and sensor and need a garage to fit it for me. If anyone could recommend a garage in or around north west London that could fit it for me at a reasonable price I would be very grateful!

Thank you

Thank you

Pica-Pica

16,736 posts

115 months

Wednesday 11th November 2020
quotequote all
I may be wrong, but I can’t see how a ring can go wrong. A sensor maybe.

6cylGolf

927 posts

221 months

Wednesday 11th November 2020
quotequote all
they swell due to rusting driveshaft
take the sensor out clean the ring through the hole
place washer (0.5-1.0mm) under sensor bolt hole
free fix

stevemcs

10,411 posts

124 months

Wednesday 11th November 2020
quotequote all
The pick up rings are usually £10, the sensor £40 so its best to replace them around the same time, budget 2 hours ish to do them assuming the driveshaft comes out of the hub. Let the garage supply the parts.

dasbimmerowner

366 posts

172 months

Thursday 12th November 2020
quotequote all
I had this about 18 months ago on one of my cars, it cost £300 to fix at a BMW specialist.

BFleming

3,921 posts

174 months

Thursday 12th November 2020
quotequote all
Pica-Pica said:
I may be wrong, but I can’t see how a ring can go wrong. A sensor maybe.
They split, and can hit the sensor, damaging it.


The big risk with sensor removal is breaking it. Very common in older BMWs.

EllzJ

Original Poster:

6 posts

72 months

Wednesday 18th November 2020
quotequote all
Hello all,

Thank you for your responses on this.

I spaced the sensor from the washer on the weekend which hasn't rectified the issue unfortunately.

I've just noticed that the corner with the problem has a different speed rating to the rest of the tyres (rated V where the rest are all rated W). It seems this could be the problem.

Zener

19,466 posts

252 months

Wednesday 18th November 2020
quotequote all
6cylGolf said:
they swell due to rusting driveshaft
take the sensor out clean the ring through the hole
place washer (0.5-1.0mm) under sensor bolt hole
free fix
Only works to a degree before the CV joint rusts some more thus swelling the ABS ring further and out of true before tting the sensor scratchchin back to square one

bodhi

14,837 posts

260 months

Wednesday 18th November 2020
quotequote all
Had the same on my 125i, iirc it was around £450 to get replaced, as my driveshafts were pretty rusty and it was touch and go if they'd need replaced. As a workaround I could just turn the DTC off and the issue would go away, fine in summer, less ideal in winter however.

monty999

1,240 posts

136 months

Wednesday 18th November 2020
quotequote all
Maybe just replace the sensor would be my thinking.Not familiar with the access on these to give the ring a clean up with a small wire brush and replace sensor (Fleabay probably have plenty). Different vehicle, but just had abs/traction light on my tranny. Had it read and just replaced sensor, sorted.

Sim89

1,622 posts

238 months

Thursday 19th November 2020
quotequote all
Definitely the reluctor ring. I wouldn't just replace the sensor as the ring swells and causes interference with the sensor.

If you can get the driveshaft out, the ring is quite easy to replace (£10) and the sensor too (£40).