Balancing a washing machine properly
Balancing a washing machine properly
Author
Discussion

cobra kid

Original Poster:

5,627 posts

271 months

Friday 12th February 2021
quotequote all
Probably the wrong section - but....

I've generally been quite lucky with washing machines and their stability over the years. however, the newest one has been a constant thorn in my side. I've a feeling it's to do with the surface it's on as it's in the garage on a tiled floor and I'm not sure how level it is.

AO delivered it and got it spinning empty and said it was fine. Since then it's been wandering around to the point I'm quite nervous!

I've had it so it's rock steady then a few days later, off it goes again.

Is there a trusted method to follow???

h0b0

9,103 posts

227 months

Friday 12th February 2021
quotequote all
Windows 10

h0b0

9,103 posts

227 months

Friday 12th February 2021
quotequote all
Is it not level or is it walking? Does it rock? If so, use the adjustable feet to level it. If not, then it is your tile floor causing slip. You can buy rubber feet to stop it moving.

BlackTails

4,040 posts

86 months

Friday 12th February 2021
quotequote all
cobra kid said:
Probably the wrong section - but....

I've generally been quite lucky with washing machines and their stability over the years. however, the newest one has been a constant thorn in my side. I've a feeling it's to do with the surface it's on as it's in the garage on a tiled floor and I'm not sure how level it is.

AO delivered it and got it spinning empty and said it was fine. Since then it's been wandering around to the point I'm quite nervous!

I've had it so it's rock steady then a few days later, off it goes again.

Is there a trusted method to follow???
Spirit level along the top back edge. It is isn't level, lift one end of the spirit level until it is. Measure the gap from the spirit level to the top surface of the machine. That's how much to lift the corner under the lifted end by.

Repeat for each top edge until the top is completely level. If it still wobbles, burn it.

cobra kid

Original Poster:

5,627 posts

271 months

Friday 12th February 2021
quotequote all
BlackTails said:
Spirit level along the top back edge. It is isn't level, lift one end of the spirit level until it is. Measure the gap from the spirit level to the top surface of the machine. That's how much to lift the corner under the lifted end by.

Repeat for each top edge until the top is completely level. If it still wobbles, burn it.
Might take the digital protractor home from work and do it properly.

Griffgrog

740 posts

277 months

Friday 12th February 2021
quotequote all
Silly question maybe, but they did remove transit bolts didn't they.

Chicken_Satay

2,519 posts

235 months

Friday 12th February 2021
quotequote all
If you haven't updated the anti virus software recently, I'd recommend doing that. I had the same issue but once the update was done, it was running as smooth as silk.

Big Rig

8,999 posts

218 months

Saturday 13th February 2021
quotequote all
Griffgrog said:
Silly question maybe, but they did remove transit bolts didn't they.
This. Mine were tight as hell to get out and had quite the length on them!

rix

2,964 posts

221 months

Saturday 13th February 2021
quotequote all
Probably needs a proper geo set-up and corner weighting....

Paul Drawmer

5,169 posts

298 months

Saturday 13th February 2021
quotequote all
Well worth doing. Mine was under the worktop and the screeded floor wasn't level.
So I had to slide the machine in to check the level fore and aft, and side to side. Then pull it out, adjust, and re check.

The washing up liquid is to help slide the machine in and out. The wooden block is to lift the machine with the wooden batten to allow the adjustment.
Don't forget the bolts have lock nuts. Undo the nut, adjust the actual bolt, lock up with the nut.