Tyre Width Laws and Penalties?
Tyre Width Laws and Penalties?
Author
Discussion

430Devil

Original Poster:

21 posts

231 months

Tuesday 18th March 2008
quotequote all
I'm pretty sure its illegal for tyres to exceed the wheel arch but can anyone quote me something legal including penalties associated?

Someone I know has has just spent a small fortune on new alloys that will exceed the arch so I'm hoping i can find something out so they don't waste their money!

Thanks

TPS

1,860 posts

244 months

Tuesday 18th March 2008
quotequote all
Yes its illegal.The tyre must not protrude the wheel arch.It would come somewhere under the construction and use regulations.Also a safety issue if it is going to catch the arch lip etc.

Edited by TPS on Tuesday 18th March 23:01

moparmick

690 posts

264 months

Fat Richie

1,271 posts

249 months

Tuesday 18th March 2008
quotequote all
As far as I recall, C&U says that 75% of the tyre tread has to be covered when viewed from above.

jaf01uk

1,943 posts

227 months

Wednesday 19th March 2008
quotequote all
Classic you tube clip, I remember that advert from my childhood and still refer to them as carlos fandangos occasionally, brilliant!! And I was recalling off the top of my head it was about a quarter of an inch of tread viewed from above, hence the bubble arches fitted to the rs escorts,
Cheers,
Gary

elwe

192 posts

251 months

Wednesday 19th March 2008
quotequote all
The tyre can stick out as much as you like. The wheel must be completely covered when viewed from above.

I remember seeing on Road Wars they stopped a knobber in a fwd escort who had fitted very wide rear wheels which stuck out of the arches. I think he got 3 points and a 60 pound fine for each wheel.

If you want a legal source take a look at the SVA manual. I believe (hope!) that follows the C&U regs.

Edited by elwe on Wednesday 19th March 11:25

430Devil

Original Poster:

21 posts

231 months

Wednesday 19th March 2008
quotequote all
Thanks for the pointers guys, I'll pass this info on. beer

flemke

23,515 posts

268 months

Wednesday 19th March 2008
quotequote all
elwe said:
The tyre can stick out as much as you like. The wheel must be completely covered when viewed from above.
You are saying that all that matters is that no part of the wheel can protrude beyond the wider of the tyre or the wing?

Strangely Brown

16,271 posts

262 months

Wednesday 19th March 2008
quotequote all
flemke said:
elwe said:
The tyre can stick out as much as you like. The wheel must be completely covered when viewed from above.
You are saying that all that matters is that no part of the wheel can protrude beyond the wider of the tyre or the wing?
If that's true then all those "Euro-Stylee" boyz have got serious problems.

elwe

192 posts

251 months

Thursday 20th March 2008
quotequote all
The tyre can be completely ignored. The wing must cover the entire wheel when viewed from above. The tyre covering the wheel from above doesn't count, it must be the wing/bubble arch/wing trim etc.

Look at the front cycle wings on a Caterfield type car. The tyres usually stick out the front and sides of the wing, but the wheel is covered by the wing. To stop spray/debris coming up you want to position the wing as far back round the wheel as possible, so you need to aim to have the front edge of the wing directly above the front of the wheel, the tyre will typically have a radius a few inches bigger than the wheel so it will stick out a few inches at the front.

I failed SVA on one rear wheel because the camber in that wheel meant that while the top of the wheel was inside the arch, the bottom prodruded by a few mm. The tyre came out a good 10mm more, but that doesn't matter. The mesurments are only taken while the car is at rest, not throughout the travel of the suspension. I added some wing piping (plastic trim with a sperm cross section, 10mm diamater head and 40mm long tain) to the wing such that the bead (sperm head) ran round the wheel arch but stuck out, thus increasing the width of the wing by 10mm. That passed the SVA. It was stuck on with silicon and retained with metal clips, but would you believe it fell off shortly after the SVA?

Edited by elwe on Thursday 20th March 10:29

Jonny_uk

305 posts

236 months

Thursday 20th March 2008
quotequote all
I always though the law was when viewed from above or veiwed in line with the edge of the wing then you should not be able to see any of the tread...sidwall is acceptable but just no actual tread. As for wheels, lookt at wire wheeled cars, the spinners stick outside the wing!

Altrezia

8,742 posts

242 months

Saturday 12th July 2008
quotequote all
Jonny_uk said:
I always though the law was when viewed from above or veiwed in line with the edge of the wing then you should not be able to see any of the tread...sidwall is acceptable but just no actual tread. As for wheels, lookt at wire wheeled cars, the spinners stick outside the wing!
You're correct. no ide what Elwe is on about.

petermansell

868 posts

237 months

Saturday 12th July 2008
quotequote all
Jonny_uk said:
I always though the law was when viewed from above or veiwed in line with the edge of the wing then you should not be able to see any of the tread...sidwall is acceptable but just no actual tread. As for wheels, lookt at wire wheeled cars, the spinners stick outside the wing!
Me too yes

Dwight VanDriver

6,583 posts

275 months

Sunday 13th July 2008
quotequote all
There is no actual cut and dried stipulation on this but Reg 63 MV (Con and Use) Regs 1986 could be invoked as it states (with exceptions non relevant to post):

heavy motor cars, motor cars and motor cycles, not being agricultural motor vehicles or pedestrian-controlled vehicles shall be equipped with wings or other similar fittings to catch, so far as practicable, mud or water thrown up by the rotation of its wheels or tracks unless adequate protection is afforded by the body of the vehicle.

Max fine: £1000 more if a goods/pass veh involved.

or even Section 40A RT Act 1988 - parts and accessories in such condition as likely to cause danger

Max fine £2500 (more if goods/pass vehicle), discretionary disq, 3 points.

dvd

Kentish

15,169 posts

265 months

Monday 14th July 2008
quotequote all
Interesting.

My tyres protrude by a few mm's past the arches and it just passed the MOT.


^Slider^

2,874 posts

280 months

Monday 14th July 2008
quotequote all
Passing the MOT doesnt mean its legal.

There are things that will pass an MOT but you could get points / penalties for.

Big Rod

6,265 posts

247 months

Monday 14th July 2008
quotequote all
Tread must be coverd by the footprint of the car, tyrewall and tread don't have to be, but I think there's a limit as to how much they stick out.

esselte

14,626 posts

298 months

Monday 14th July 2008
quotequote all
^Slider^ said:
Passing the MOT doesnt mean its legal.

There are things that will pass an MOT but you could get points / penalties for.
Are you talking about itmes that are actually tested?

^Slider^

2,874 posts

280 months

Monday 14th July 2008
quotequote all
Well insecure battery would pass MOT, but would get 3 points for dangerous parts or accessory.

So not items that are actually tested so to speak. But itmes that would attract points for dangerous condition etc may not be examined on the MOT or would not fail the MOT.

liner33

10,861 posts

233 months

Tuesday 15th July 2008
quotequote all
Jonny_uk said:
I always though the law was when viewed from above or veiwed in line with the edge of the wing then you should not be able to see any of the tread...sidwall is acceptable but just no actual tread. As for wheels, lookt at wire wheeled cars, the spinners stick outside the wing!
Thats how i was told , i had a Mk1 Capri with front tyres which stuck clearly proud of the already rolled arches but due to the hockey stick shape in the front wings no tread was visable from above although many officers tried