Daft question - could well be one for Balmoral Green!
Discussion
I have recently moved into a house where all the exterior doors are double glazed units – except the front door of course.
The problem I am having is that because of this we have no easy access route for the cat and having to keep an eye out for her constantly is driving me nuts!
A colleague mentioned that cat flaps can be put into double glazed windows (e.g. door into conservatory) but the whole unit has to be supplied by the factory as they will ensure it remains sealed.
Does anyone know if this is correct and how much it costs? The only other alternative I have is to go through the brickwork or the front door, both of which I would rather avoid.
This is a really daft problem to have and I realise is an odd question but any help would be appreciated.
Cheers
Matt
The problem I am having is that because of this we have no easy access route for the cat and having to keep an eye out for her constantly is driving me nuts!
A colleague mentioned that cat flaps can be put into double glazed windows (e.g. door into conservatory) but the whole unit has to be supplied by the factory as they will ensure it remains sealed.
Does anyone know if this is correct and how much it costs? The only other alternative I have is to go through the brickwork or the front door, both of which I would rather avoid.
This is a really daft problem to have and I realise is an odd question but any help would be appreciated.
Cheers
Matt
wanty1974 said:MattW was talking about the conservatory door. This will most likely be either a wooden or PVCu door frame with a large glass sealed unit (two panes of glass separated by an aluminium spacer and sealed). You'd just have to pop one unit out and replace it with another which is a five minute job.
I thought the door was a sealed unit? Does that mean you can have half your door replaced?
>> Edited by Frik on Monday 6th March 15:23
Frik said:
wanty1974 said:MattW was talking about the conservatory door. This will most likely be either a wooden or PVCu door frame with a large glass sealed unit (two panes of glass separated by an aluminium spacer and sealed). You'd just have to pop one unit out and replace it with another which is a five minute job.
I thought the door was a sealed unit? Does that mean you can have half your door replaced?
>> Edited by Frik on Monday 6th March 15:23
Yup, conservatory door is PVC with a large single piece sealed glass unit within it. I assume it is a case of finding a manufacturer who can replace it, or does it have to be the original supplier?
MattW said:Doesn't have to be the original manufacturer - just go to your local glass shop and they should be able to sort you out.
Yup, conservatory door is PVC with a large single piece sealed glass unit within it. I assume it is a case of finding a manufacturer who can replace it, or does it have to be the original supplier?
A couple of things to bear in mind:
- The hole cannot be too close to the edge of the unit so the flap will be a little way off the ground (a box either side of the door may be of use to you cat here - they generally hate using flaps anyway)
- You will need a flap specifically design for use in glass, though the glass shop should have some prior knowledge of this.
- The unit will have to be toughened glass (as it's in an exterior door).
Corpulent Tosser said:
Surprised no-one has suggested getting rid of the cat.
It is the wifes cat, if I was to suggest that I can guess the answer so I am not even going there....................mind you I am sure I could make the garage quite comfortable........................for me you understand, not the cat!
Bump!
Just spoken to the Double Glazing outfit that fitted the windows and they say it cannot be done and that they would have to fit a split piece of glass in the bottom of the door i.e. a plastic panel that a hole could be easily cut in.
Can anyone point me the direction of someone who might be able to help down on the south coast?
Cheers
Matt
Just spoken to the Double Glazing outfit that fitted the windows and they say it cannot be done and that they would have to fit a split piece of glass in the bottom of the door i.e. a plastic panel that a hole could be easily cut in.
Can anyone point me the direction of someone who might be able to help down on the south coast?
Cheers
Matt
Sorry, missed this thread.
It is very difficult to do in a double glazed glass unit, you cannot do square holes as the glass is weak in the corners and breaks, often before the task is accomplished if anyone is daft enough to try, even if they did achieve it, it would probably break within minutes. Round holes can be cut, for an extractor fan for example, it was easy in a single sheet of glass, but with a double glazed unit the spacer bar and sealant around the circular hole has to be done by hand, the outside edge of the unit is done by machine.
Basically it is a pain in the arse, so most folks would say no, it cant be done. Best thing to do is use a flat PVCu panel and cut that. The flat panel fits into the frame in the same way as does a sealed unit.
If the door is fully glazed, eg one large unit filling the whole frame, it may be possible to fit a midrail by using mechanical joints, then glazing above the midrail and flat panel below. But getting a midrail from the same extruded profile would be difficult, and once again, no one will be arsed to do it for you.
Replacing the door for a simple white PVCu with a midrail, glass above, panel below, would be about £450 at the very budget specification end of the market, around £850 for a top specification. Or as is common in this industry, about £850 for a budget specification because they always pretend it is top spec to start with and then work the price down to where it should have been in the 1st place, with the deal closed at anywhere in between.
It is very difficult to do in a double glazed glass unit, you cannot do square holes as the glass is weak in the corners and breaks, often before the task is accomplished if anyone is daft enough to try, even if they did achieve it, it would probably break within minutes. Round holes can be cut, for an extractor fan for example, it was easy in a single sheet of glass, but with a double glazed unit the spacer bar and sealant around the circular hole has to be done by hand, the outside edge of the unit is done by machine.
Basically it is a pain in the arse, so most folks would say no, it cant be done. Best thing to do is use a flat PVCu panel and cut that. The flat panel fits into the frame in the same way as does a sealed unit.
If the door is fully glazed, eg one large unit filling the whole frame, it may be possible to fit a midrail by using mechanical joints, then glazing above the midrail and flat panel below. But getting a midrail from the same extruded profile would be difficult, and once again, no one will be arsed to do it for you.
Replacing the door for a simple white PVCu with a midrail, glass above, panel below, would be about £450 at the very budget specification end of the market, around £850 for a top specification. Or as is common in this industry, about £850 for a budget specification because they always pretend it is top spec to start with and then work the price down to where it should have been in the 1st place, with the deal closed at anywhere in between.
Thanks for the comments guys.
Not sure I want to remove the complete glass unit and replace with half PVCu though as it will spoil the look of the conservatory.
PDV6 don't suppose you know who did the work for your friends?
Oh well at this rate the cat is going to just have to learn to shout louder......that'll please the neighbours!
Not sure I want to remove the complete glass unit and replace with half PVCu though as it will spoil the look of the conservatory.
PDV6 don't suppose you know who did the work for your friends?
Oh well at this rate the cat is going to just have to learn to shout louder......that'll please the neighbours!

Gassing Station | The Pie & Piston Archive | Top of Page | What's New | My Stuff





