Oil rig question....
Discussion
A typical oil production platform is self-sufficient in energy and water needs, housing electrical generation, water desalinators and all of the equipment necessary to process oil and gas such that it can be either delivered directly onshore by pipeline or to a Floating Storage Unit and/or tanker loading facility. Elements in the oil/gas production process include wellhead, production manifold, production separator, glycol process to dry gas, gas compressors, water injection pumps, oil/gas export metering and main oil line pumps. All production facilities are designed to have minimal environmental impact.
http://en.wikipedia.org/wiki/Oil_rig
http://en.wikipedia.org/wiki/Oil_rig
OK, first thing is to sort out some terminology here. The term 'rig' is often, incorrectly, used to describe any 'installation'. For me, a 'rig' is a mobile (drilling) unit (jack-up or semi-submersible).
So, rigs are powered by by diesel generators. The diesel is delivered by supply vessel and stored in bulk tanks.
Fixed installations (platforms, semi's and FPSO's)are mostly purely for production and export (but may have a permanent drilling facility incorporated in the topside. These are almost all powered by on-board generation. The difference is that in many cases, the generators burn produced gas (separated on-board in the process plant).
Some smaller installations (like not normally manned platforms) may be powered from a host facility via a power cable installed on the seabed.
In the North Sea, the only exception I can think of is the Beryl 'A' platform currently operated by Ithaca Energy (recently aquired from Talisman). The (fixed) platform is in the Moray Forth and is close enough to shore that it is powered via a cable to shore and (I think) the national grid.
Cheers,
Eric
So, rigs are powered by by diesel generators. The diesel is delivered by supply vessel and stored in bulk tanks.
Fixed installations (platforms, semi's and FPSO's)are mostly purely for production and export (but may have a permanent drilling facility incorporated in the topside. These are almost all powered by on-board generation. The difference is that in many cases, the generators burn produced gas (separated on-board in the process plant).
Some smaller installations (like not normally manned platforms) may be powered from a host facility via a power cable installed on the seabed.
In the North Sea, the only exception I can think of is the Beryl 'A' platform currently operated by Ithaca Energy (recently aquired from Talisman). The (fixed) platform is in the Moray Forth and is close enough to shore that it is powered via a cable to shore and (I think) the national grid.
Cheers,
Eric

Kiltie said:
OK, first thing is to sort out some terminology here. The term 'rig' is often, incorrectly, used to describe any 'installation'. For me, a 'rig' is a mobile (drilling) unit (jack-up or semi-submersible).
So, rigs are powered by by diesel generators. The diesel is delivered by supply vessel and stored in bulk tanks.
Fixed installations (platforms, semi's and FPSO's)are mostly purely for production and export (but may have a permanent drilling facility incorporated in the topside. These are almost all powered by on-board generation. The difference is that in many cases, the generators burn produced gas (separated on-board in the process plant).
Some smaller installations (like not normally manned platforms) may be powered from a host facility via a power cable installed on the seabed.
In the North Sea, the only exception I can think of is the Beryl 'A' platform currently operated by Ithaca Energy (recently aquired from Talisman). The (fixed) platform is in the Moray Forth and is close enough to shore that it is powered via a cable to shore and (I think) the national grid.
Cheers,
Eric
Ahh so thats the big thing I can see from my window right now So, rigs are powered by by diesel generators. The diesel is delivered by supply vessel and stored in bulk tanks.
Fixed installations (platforms, semi's and FPSO's)are mostly purely for production and export (but may have a permanent drilling facility incorporated in the topside. These are almost all powered by on-board generation. The difference is that in many cases, the generators burn produced gas (separated on-board in the process plant).
Some smaller installations (like not normally manned platforms) may be powered from a host facility via a power cable installed on the seabed.
In the North Sea, the only exception I can think of is the Beryl 'A' platform currently operated by Ithaca Energy (recently aquired from Talisman). The (fixed) platform is in the Moray Forth and is close enough to shore that it is powered via a cable to shore and (I think) the national grid.
Cheers,
Eric


Mactac said:
Cheers for that Eric.
I suppose that thread on an 'installation' being evacuated the other month on here made me think, as someone said the thing was a series of 'rigs?' Joined together in a row.
Sounded like a small town.
Maybe this one? A series of installations connected together, with several helidecks, cranes, accommodation modules etc. I took this in the North sea a couple of years ago.I suppose that thread on an 'installation' being evacuated the other month on here made me think, as someone said the thing was a series of 'rigs?' Joined together in a row.
Sounded like a small town.

It's not lit up because, er, its daylight

polus said:
Mactac said:
Obviously I'm going to ask what they are burning off
so flamboyantly like an 'olympic torch' poking ou the side, on every occasion I see them on telly..
I was under the impression is was excess gas that had to be released to stop pressure building up to a dangerous level, and you cant just release it, so it gets burnt. so flamboyantly like an 'olympic torch' poking ou the side, on every occasion I see them on telly..
Edited by Mactac on Saturday 19th April 20:40
...Waits for someone to correct me

Planned flaring due to ongoing operations. All oil/gas processing has some extent of controlled flash gas loss that can't be used at the pressures they boil off and also clean gas is often used as a utility to purge systems of air or whatever. You have some choices about what you do with this, you either burn it (the flare) or you re-compress this flash gas and push it back into the processing train. The problem is that this requires extra equipment (bad offshore) and is an energy overhead.
During maintenance or shut down or star-up of a oil and gas processing train gas is always produced either too quickly, to slowly out of sync or you just have to dump an inventory already present that might be off-spec or difficult to do anything else with. Pretty mich your only choice in an isolated facility is to flare this off.
Finally in the event of an emergency a plant will shut down automatically in a pre-programmed controlled fashion (well thats the plan) when this happens emergency shut down valves will act and the facility will blow-down to the flare. Subsequently the plant should be left in a safe condition and if there is a fire the inventory should be minimised to reduce fire risk.
The extent of flaring you'll see generally depends on the field and the gas to oil ratio therein. Considering that oil is the pay dirt or gold or always has been, gas used to be a troublesome by product then if the oil came up with a load of gas you had to flare it.
In some places namely Norway, they have tried to eliminate ongoing flaring altogether, meaning they'd only flare in an emergency which is great. Until you need to light the bloody thing in an emergency!
Thats basically it in laymans terms. Someone who knows more than me will probably pick up on something I've missed.
Right, that's the tatties on. 
Olf has covered everything (and sounds like a process engineer
). The only thing I'd ad is that flaring (in the UKCS) is strictly controlled. Operator companies have to negotiate an annual flaring consent with the authorities (primarily the DTi).
Exceeding figures in the consent is a matter treated with a great deal of gravity.
Olf mentions geting the flare lit in an emergency. I think they mostly have some sort of pilot light arrangement. When this goes out however it means someone is in for a bit of fun as the conventional method for re-lighting the flare is shooting a firework into the vented gas at the flare tip.
Working on a diving or construction vessel (my roots) underneath a flare can be interesting. On some older installations with constant flaring, I remember being out on the bridge wings like being on Mediterranean beach at midday in the Summer. I remember an instance where the plant tripped and the flare went to full pelt without the platform letting the boat know. It melted the fast rescue boat (which had a full tank of fuel!) - close one. Then there's the isue of liquid carry-over if the flare train isn't working efficiently (Olf - knockout drums?) It has been known for big globs of boiling pitch to land on a vessel's deck.
Cheers,
Eric

Olf has covered everything (and sounds like a process engineer
). The only thing I'd ad is that flaring (in the UKCS) is strictly controlled. Operator companies have to negotiate an annual flaring consent with the authorities (primarily the DTi).Exceeding figures in the consent is a matter treated with a great deal of gravity.
Olf mentions geting the flare lit in an emergency. I think they mostly have some sort of pilot light arrangement. When this goes out however it means someone is in for a bit of fun as the conventional method for re-lighting the flare is shooting a firework into the vented gas at the flare tip.
Working on a diving or construction vessel (my roots) underneath a flare can be interesting. On some older installations with constant flaring, I remember being out on the bridge wings like being on Mediterranean beach at midday in the Summer. I remember an instance where the plant tripped and the flare went to full pelt without the platform letting the boat know. It melted the fast rescue boat (which had a full tank of fuel!) - close one. Then there's the isue of liquid carry-over if the flare train isn't working efficiently (Olf - knockout drums?) It has been known for big globs of boiling pitch to land on a vessel's deck.
Cheers,
Eric

Gassing Station | The Pie & Piston Archive | Top of Page | What's New | My Stuff







