Boiler Problem
Author
Discussion

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Well not really a problem, just a question. My boiler has 2 dials on it, both of which go from 5 - 80 (which I assume is degrees for water temp?) and both can be switched off independently via their own switch on the wall.

My question is what do they both do, I assume one is an immersion heat but what is the other? And how do I tell which is which. Also what do the dials do, as they are both set to 30 and the water is still to hot. I have tried turning both down to 5 but that doesn't seem to make much difference either.

I only ask as I my electricity bills (don't have gas) seem to be far to much for a 2 bed flat (£65 per month).

Here are some pics;




shirt

25,556 posts

232 months

Monday 28th July 2008
quotequote all
would assume 1 for water, 1 for central heating.


Olf

11,978 posts

249 months

Monday 28th July 2008
quotequote all
That's not a boiler. It's a water cylinder fitted with imersion heaters. It's a small but important point to clarify.

Edited by Olf on Monday 28th July 14:55

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Olf said:
That's not a boiler. It's a water cylinder fitted with emersion heaters. It's a small but important point to clarify.
Fair point!

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
shirt said:
would assume 1 for water, 1 for central heating.

Dont have central heating, just storage heaters in each room.

pies

13,116 posts

287 months

Monday 28th July 2008
quotequote all
Im guessing one tank with two heaters

Stig

11,823 posts

315 months

Monday 28th July 2008
quotequote all
Pies is right(ishwink )

You have an immersion heater with primary (top) and secondary elements. The hot water is taken from the top of the tank, so you would normally set the upper one (immersion heating element) at a higher temp than the lower one.

Basically, it gives you a choice as to how much water to heat (and is therefore available to use) at a time.

Edited by Stig on Monday 28th July 15:13

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Thanks.

So can I switch one of them off if I want to reduce my bill and what sort of temp should I be setting them at?

I have just noticed that the top one is currently switch off, so I guess I would be better swithcing the bottom one off and only keep a small amount of water ready.


Edited by 1 on Monday 28th July 15:43

Pigeon

18,535 posts

277 months

Monday 28th July 2008
quotequote all
Yeah, run it on the top one for most of the time, use the bottom one when you have a bath.

Standard temp to set them at is 60 deg C.

dan1981

18,129 posts

230 months

Monday 28th July 2008
quotequote all
THREAD HIJACK - SIMILAR BOILER PROBLEM

Right then, we seem to have a similar setup to the OP. A tank like this with only one switch - for the immersion heater.

However thermostat fro this has gone so apparently we can't have it turned on or the water just biols and keeps getting hotter and hotter.

With it switched off do i just have to use the hot water in the tank? (presumabley by turning on the hot water at the switch downstairs?)

i'm really techincal me!

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Pigeon said:
Yeah, run it on the top one for most of the time, use the bottom one when you have a bath.

Standard temp to set them at is 60 deg C.
Thanks.

Pigeon

18,535 posts

277 months

Monday 28th July 2008
quotequote all
dan1981 said:
THREAD HIJACK - SIMILAR BOILER PROBLEM

Right then, we seem to have a similar setup to the OP. A tank like this with only one switch - for the immersion heater.

However thermostat fro this has gone so apparently we can't have it turned on or the water just biols and keeps getting hotter and hotter.

With it switched off do i just have to use the hot water in the tank? (presumabley by turning on the hot water at the switch downstairs?)

i'm really techincal me!
Get a new thermostat, they cost less than a fiver and it's two screws to change them.

If you have only the immersion heater for hot water, it will fail again, because they are st and can only withstand occasional use, but it'll work for a year or two.

Ferg

15,242 posts

288 months

Monday 28th July 2008
quotequote all
I'm going to have to disagree with some of this thread....

The bottom immersion should heat the whole tank at night on cheap rate electricity. Only use the top one in emergencies when you run out and need a bit more. Bear in mind this is now heating with peak rate electricity.

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Ferg said:
I'm going to have to disagree with some of this thread....

The bottom immersion should heat the whole tank at night on cheap rate electricity. Only use the top one in emergencies when you run out and need a bit more. Bear in mind this is now heating with peak rate electricity.
Well that has put the cat among the pigeons! hehe

So who is right? What is your experience of these things Ferg / Pigeon?


Simpo Two

93,093 posts

296 months

Monday 28th July 2008
quotequote all
I wonder how many millions the leccy companies make because the two heaters are not marked 'Cheap' and 'Peak'?

Ferg

15,242 posts

288 months

Monday 28th July 2008
quotequote all
I have to say that disagreeing with Pigeon is something I wouldn't want to try to do unless I was absolutely sure...... smile

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Ferg said:
I have to say that disagreeing with Pigeon is something I wouldn't want to try to do unless I was absolutely sure...... smile
O.k so you sound pretty confident. Now I need to re-think why my bills are so high as the top one has been switched off and I haven't turned the heating on in months.

Ferg

15,242 posts

288 months

Monday 28th July 2008
quotequote all
Check to see how it's controlled.
Sometimes the bottom heater is wired directly to the cheap side of the meter. Sometimes they go via a timeswitch and the whole house goes over to cheap rate. If it's the latter I suppose it might be heating the whole thing at the wrong time?? Do you have a time clock on it?

1

Original Poster:

2,732 posts

267 months

Monday 28th July 2008
quotequote all
Ferg said:
Check to see how it's controlled.
Sometimes the bottom heater is wired directly to the cheap side of the meter. Sometimes they go via a timeswitch and the whole house goes over to cheap rate. If it's the latter I suppose it might be heating the whole thing at the wrong time?? Do you have a time clock on it?
No there isnt a clock on it.

Ferg

15,242 posts

288 months

Monday 28th July 2008
quotequote all
OK. Check a couple of things.

Are you actually on a cheap rate at night (look at bills, or maybe the meter will show two readings)?

Is the bottom heater LIVE during the day? Switch it on and off and you may see the ceiling light dim slightly. Or you may hear it humming if you put your ear to it. OR you might test for live on the brown wire... paperbag