brake pad buffers
Discussion
Hi I found this, and if your lucky the pads still fit origenally...ad the stick on rubber on the back on theplace where the piston touch the pads! so the piston touch the rubber on the pads it could loose the direkt braking feeling though cause of the little damping the piston and direkt contact...maybe there are some other sellutions? in my cardays when I work with brakes I used coppergreese on the back and where they slide in the callipers(never get any vet on the brake-side though!)
but this story below tels that its not good anough? but you can give it a try..and when it not helps anough the pads are more worked in and the stick-rubbers wil fit better
-----------------------
Pagid Squeal
-------------------------------------------------------------------------------------------
OK - so having managed to fit the Pagids - the next problem was a banshee-squeal whenever we slowed the car down to a stop (it's fine at speed - just in the final stages of coming to a halt). This squeal was LOUD and very embarrassing in town...
We had (of course) tried copper-grease on the backs of the pads - but it didn't help and the grease soon seemed to dry up or otherwise disappear. We spoke to John at Performance Braking (again) and he sent us some special stick-on backing pads to try (a kind of dense, heat-resistant rubber made by 3M). This caused our next problem - the rubber pads increased the overall depth of the Pagids by a good 1mm each side - and so more friction material needed to be removed in order to get the Pagids back into the calipers at all...
This is where impatience got the better of us - we used a belt-sander to take the friction material off. On reflection, we should have paid more attention to making sure the pad surfaces stayed flat and true - but we didn't...
The anti-squeal pads worked to a degree - but introduced an unwanted amount of sponginess into the feel of the pedal - so they had to go... We have tried chamfering the leading edges of the pads (by 45 degrees) using a hand-file - and this has been somewhat effective - but that damned squeal still remains. Ho-hum.
----------------------------------------------------------------------------------------
GTRene
but this story below tels that its not good anough? but you can give it a try..and when it not helps anough the pads are more worked in and the stick-rubbers wil fit better
-----------------------
Pagid Squeal
-------------------------------------------------------------------------------------------
OK - so having managed to fit the Pagids - the next problem was a banshee-squeal whenever we slowed the car down to a stop (it's fine at speed - just in the final stages of coming to a halt). This squeal was LOUD and very embarrassing in town...
We had (of course) tried copper-grease on the backs of the pads - but it didn't help and the grease soon seemed to dry up or otherwise disappear. We spoke to John at Performance Braking (again) and he sent us some special stick-on backing pads to try (a kind of dense, heat-resistant rubber made by 3M). This caused our next problem - the rubber pads increased the overall depth of the Pagids by a good 1mm each side - and so more friction material needed to be removed in order to get the Pagids back into the calipers at all...
This is where impatience got the better of us - we used a belt-sander to take the friction material off. On reflection, we should have paid more attention to making sure the pad surfaces stayed flat and true - but we didn't...
The anti-squeal pads worked to a degree - but introduced an unwanted amount of sponginess into the feel of the pedal - so they had to go... We have tried chamfering the leading edges of the pads (by 45 degrees) using a hand-file - and this has been somewhat effective - but that damned squeal still remains. Ho-hum.
----------------------------------------------------------------------------------------
GTRene
Edited by GTRene on Saturday 29th July 16:49
Take a look here
www.elise-faq.info/content/brakes/index.php
and position of buffer pads here
www.elise-faq.info/content/brakes/caliper1.php
The buffers are to stop the pads rattling up and down in the caliper not stop the squealing. RS42 may squeak a bit when used lightly - anti squeal shims etc can be fitted to help this but you may lose some of the pedal feel as the shim needs to be first compressed when the pedal is pushed.
I fitted the anti rattle buffers but didn't bother with any backing to the pads to stop squealing - big improvement over standard and squealing isn't a problem - just give them some abuse once in a while
www.elise-faq.info/content/brakes/index.php
and position of buffer pads here
www.elise-faq.info/content/brakes/caliper1.php
The buffers are to stop the pads rattling up and down in the caliper not stop the squealing. RS42 may squeak a bit when used lightly - anti squeal shims etc can be fitted to help this but you may lose some of the pedal feel as the shim needs to be first compressed when the pedal is pushed.
I fitted the anti rattle buffers but didn't bother with any backing to the pads to stop squealing - big improvement over standard and squealing isn't a problem - just give them some abuse once in a while
some more here...
The squeaking noise can sometimes be reduced or eliminated by coating the back side of the pad with an anti-squeak material. Several types of material are sold by the manufacturers of brake parts. Some are like a silicone rubber that cushions the brake pad to the caliper so the pad does not vibrate. Other types of material are like lubricants, that allow the pad to vibrate without squeaking. Do not use ordinary grease to lubricate the back of the pad. The high temperature created by your brakes will quickly burn it off!
Finally, burnishing the brake pads will help to reduce squeals and improve braking performance. Burnishing involves heating the pads to a high temperature to burn off the glaze on them and seat them to the rotor. This is done by driving the car to a speed of about 70 to 80 kph and then braking to a stop with medium to firm brake force. Repeat the stop about ten times, allowing a full one-minute cooling off period in between stops to avoid overheating the brakes. Naturally, this procedure must be done in a safe and traffic free place. If you don't feel comfortable doing it, your local brake specialist will be happy to help you.
Jim Kerr is a master automotive mechanic and teaches automotive technology. He has been writing automotive articles for fifteen years for newspapers and magazines in Canada and the United States, and is a member of the Automotive Journalist's Association of Canada (AJAC
GTRene
I would go only for a good thin layer of coppergrease(for the direckt feeling)...and bed things in as above? or ask some racing/track guys, sure they know!
The squeaking noise can sometimes be reduced or eliminated by coating the back side of the pad with an anti-squeak material. Several types of material are sold by the manufacturers of brake parts. Some are like a silicone rubber that cushions the brake pad to the caliper so the pad does not vibrate. Other types of material are like lubricants, that allow the pad to vibrate without squeaking. Do not use ordinary grease to lubricate the back of the pad. The high temperature created by your brakes will quickly burn it off!
Finally, burnishing the brake pads will help to reduce squeals and improve braking performance. Burnishing involves heating the pads to a high temperature to burn off the glaze on them and seat them to the rotor. This is done by driving the car to a speed of about 70 to 80 kph and then braking to a stop with medium to firm brake force. Repeat the stop about ten times, allowing a full one-minute cooling off period in between stops to avoid overheating the brakes. Naturally, this procedure must be done in a safe and traffic free place. If you don't feel comfortable doing it, your local brake specialist will be happy to help you.
Jim Kerr is a master automotive mechanic and teaches automotive technology. He has been writing automotive articles for fifteen years for newspapers and magazines in Canada and the United States, and is a member of the Automotive Journalist's Association of Canada (AJAC
GTRene
I would go only for a good thin layer of coppergrease(for the direckt feeling)...and bed things in as above? or ask some racing/track guys, sure they know!
Edited by GTRene on Saturday 29th July 17:39
For the rattle, which can happen while just driving around add the small pads like Ruxpins second links suggests.
But keep an eye on them when you wash the wheels, as I think I managed to loose mine as I have a rattle again. But not had chance to have a look and see if a pad has gone missing.
For the squeal, thats only when you brake to a stop and only on the very last point of just stopping. I find one of 2 solutions,
1. just at the very point they are going to squeal ( or just as the car is about to stop.. ) just lift off the brakes and let the car stop on its own. It should be going so slow anyway the distance moved is only a foot or so...( dont roll into the car in front... )
2. Just at the squeal point, stamp on the brakes. Its a bit less smooth but does the job.
-pete
But keep an eye on them when you wash the wheels, as I think I managed to loose mine as I have a rattle again. But not had chance to have a look and see if a pad has gone missing.
For the squeal, thats only when you brake to a stop and only on the very last point of just stopping. I find one of 2 solutions,
1. just at the very point they are going to squeal ( or just as the car is about to stop.. ) just lift off the brakes and let the car stop on its own. It should be going so slow anyway the distance moved is only a foot or so...( dont roll into the car in front... )
2. Just at the squeal point, stamp on the brakes. Its a bit less smooth but does the job.
-pete
Edited by PB9 on Saturday 29th July 17:42
Slight thread drift -
Anyone know of an obvious replacement alternative to the standard pads fitted on an '06 model..? I think mine are starting to wear and was wondering what a glaringly obvious upgrade would be?
Green stuff? Red stuff? Mintex? EBC? I don't know - just interested in what the really effective, standard disc, enthusiastic road use options would be..?
Anyone know of an obvious replacement alternative to the standard pads fitted on an '06 model..? I think mine are starting to wear and was wondering what a glaringly obvious upgrade would be?
Green stuff? Red stuff? Mintex? EBC? I don't know - just interested in what the really effective, standard disc, enthusiastic road use options would be..?
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff


