If I want to get rid of my MMCs..............
If I want to get rid of my MMCs..............
Author
Discussion

veetwin

Original Poster:

1,579 posts

288 months

Tuesday 1st August 2006
quotequote all
.....what do I need? After reading 150 reasons, I am keeping the little bastid and am now thinking of making those final upgrades during the coming winter. So where do I start? New hubs? New Calipers? Or is it a simple straight swap with some steel (x-drilled) discs with normal pads.

Are there any recommendations for manufacturers/suppliers? I will be doing the work myself so anything that I should be looking out for? All help on the matter will be greatly appreciated.

Next mod will no doubt be the S2 Bilstein upgrade, look out Bank manager, here I come!!

veetwin

Original Poster:

1,579 posts

288 months

Tuesday 1st August 2006
quotequote all
Another thing is the bootlid (black plastic one on 98 S1) has split. Can I buy a new one of these?

jaykaybi

3,494 posts

252 months

Tuesday 1st August 2006
quotequote all
Good luck getting hold of Bilsteins - I'm informed they are currently back ordered well into next year, hence today I am replacing my knackered rear dampers with yet more Konis.

Edited by jaykaybi on Tuesday 1st August 13:37

veetwin

Original Poster:

1,579 posts

288 months

Tuesday 1st August 2006
quotequote all
jaykaybi said:
Good luck getting hold of Bilsteins - I'm informed they are currently back ordered well into next year, hence today I am replacing my knackered rear dampers with yet more Konis.

Edited by jaykaybi on Tuesday 1st August 13:37


That is a bit pants!

Have you tried one of the Seloc guys, can't recall his name, he deals with second hand kit I believe.

jaykaybi

3,494 posts

252 months

Tuesday 1st August 2006
quotequote all
I tried the fella (SteveB I believe) and he told me the same story - there'll be a wait.

The main dealer told me that they are up to 100 back ordered... annoyed me too.

Good luck!

mr_c

2,508 posts

260 months

Tuesday 1st August 2006
quotequote all
Why do you want to get rid of the MMC's? They're absolutely brilliant. Ok so in the wet they may need a little prod to clear the film of water off the discs and in the dry they squeal like feck, but you can't beat them for power and feel, and even lapping the nurburgring mine never faded or overheated, where everyone else was getting fade etc half way in!!!

Also, they're lighter than Iron ones so you've got less unsprung weight.

Leave them on!!!

veetwin

Original Poster:

1,579 posts

288 months

Tuesday 1st August 2006
quotequote all
Ok, can I minimise the squeal? Also, how do you tell when new pads or discs are needed???

mr_c

2,508 posts

260 months

Tuesday 1st August 2006
quotequote all
I believe there are some anti squeal shims available from lotus. Others have suggested packing the back of the pad with grease. My preferred method is a few big stops to get some heat into them!!! Or put up with the squealing. It is quite embarressing though going through a town when one of the brakes starts rubbing and squealing.. haha.

I think pads last about 70k miles and discs about 100k. After the discs have gone it might make financial sense to go to Iron, all you need to buy are the discs and pads to change mate.

veetwin

Original Poster:

1,579 posts

288 months

Tuesday 1st August 2006
quotequote all
Bloody hell 70k on one set of pads!!! My Fireblade ate it's first set on 4k!! I shall strip the brakes down this weekend and apply a load of copper grease to the back of the pads and see if it makes a difference. Right then, on to the Suspension.