Rev limiter question
Author
Discussion

cjfc

Original Poster:

38 posts

247 months

Tuesday 8th August 2006
quotequote all
Do you do any damage to the engine by hitting the rev limiter every so often when accelerating. I haven’t done it often and I lift off the accelerator as soon it happens. I’ve probably done it four / five times since having the car (about three months ownership)

I realise that the limiter is there to protect the engine from the likes of my poor accelerating / driving but wondered if you do any damage and I suppose whether lotus don’t like it when they check the ecu data if something goes wrong

Nevertheless, I clearly need to improve my gear change timing but I’m not yet used to how quickly the revs move through the second cam. It’s outstanding how quickly it happens in first and second.

Just to clarify I’m not asking about the potential damage you will do by buzzing the engine past the limiter on a downshift

Cheers all

(ps this acceleration doesn’t mean going over the NSL and I am planning another walshy day to improve my overall skills)

cej

961 posts

253 months

Tuesday 8th August 2006
quotequote all
It's OK. No harm done.

GTRene

22,798 posts

255 months

Tuesday 8th August 2006
quotequote all
as long as you use good oil and heat up the engine oil properly there is no real harm! ofcorse a engine lives a bit longer when you don't in the end, but then you would have no real fun
By the way, for fast driving its better to shift just before the rev limiter kicks in! stay in the powerband and your spot on
have fun"
GTRene

cjfc

Original Poster:

38 posts

247 months

Wednesday 9th August 2006
quotequote all
thanks guys.
i do try and shift before the limiter but i just get a bit carried away sometimes as i enjoy the sound of the second cam

Phil-CH

1,132 posts

295 months

Wednesday 9th August 2006
quotequote all
cjfc said:
thanks guys.
i do try and shift before the limiter but i just get a bit carried away sometimes as i enjoy the sound of the second cam


Ditto. I can only agree to that.. that second cam is very addictive and especially when accelerating in 1st into 2nd gear, it's very challenging to keep it on 2nd cam all the way through. I have been able to do it a few times (perfect gear change, quick, smooth clutch change but not too smooth and just the second the rev limiter is hit)...

zebra

4,555 posts

245 months

Wednesday 9th August 2006
quotequote all
You get more speed by not reaching the rev limiter. As mentioned earlier stay in power band.

If it's the noise you like get an induction kit or sports exhaust.

Zebra

Edited by zebra on Wednesday 9th August 11:29

purpleperil

1,226 posts

315 months

Wednesday 9th August 2006
quotequote all
How much 'notice' does the change up light give you of impending rev limit, or are the two one in the same?

zebra

4,555 posts

245 months

Wednesday 9th August 2006
quotequote all
Changing when the light comes on means you are still within the powerband, but there's a good 1000+ revs to go before the limiter.

Zebra

purpleperil

1,226 posts

315 months

Wednesday 9th August 2006
quotequote all
zebra said:
Changing when the light comes on means you are still within the powerband, but there's a good 1000+ revs to go before the limiter.

Zebra

You shouldn't have told me that Though I suspect usable power tends to start dropping off anyway after the red light comes on?

zebra

4,555 posts

245 months

Wednesday 9th August 2006
quotequote all
Spoke to a few guys about gear changes and limiters who used to race professionally and they got me in a comparison drag race, where I had to change as high as I could before the limiter kicked in, they were changing at 7500 rpm. Easliy out sprinted me.

There's no need to cane it.

Zebra

pjm

92 posts

254 months

Wednesday 9th August 2006
quotequote all
zebra said:
Spoke to a few guys about gear changes and limiters who used to race professionally and they got me in a comparison drag race, where I had to change as high as I could before the limiter kicked in, they were changing at 7500 rpm. Easliy out sprinted me.

There's no need to cane it.

Zebra



7.5k may well be optimal, but the red light comes on at 7.8k doesn't it? Much as I'd like to say otherwise, I doubt I could time a gearchange to within a couple of hundred revs when flat out in 2nd - I tend it run it up to 7.8 because if you mistime it and fall off-cam when you change up, that's definielty slower!

zebra

4,555 posts

245 months

Wednesday 9th August 2006
quotequote all
I'm not going to quibble over 300 revs, all I'm saying is that there is no need to rev the arse of your elise to get the best out of it. Reaching the limiter does f**k all good for the car.

Zebra

Phil-CH

1,132 posts

295 months

Thursday 10th August 2006
quotequote all
zebra said:
I'm not going to quibble over 300 revs, all I'm saying is that there is no need to rev the arse of your elise to get the best out of it. Reaching the limiter does f**k all good for the car.

Zebra


I'll agree with this for any gear change, except going from 1st into 2nd gear. If you change at ~7800 RPM, you drop far below into the lower cam and that takes more time to recover than going over the powerband, but staying in the 2nd cam mode. I am sure I can dig up a diagram of the power curve that shows that the engine still delivers more power above 8000 rpm (after the power drop-off) than it would at 5500 to 6200 rpm (the range you'd drop into if you change at around 7800 RPM).

At least, 2nd into 3rd, 3rd into 4th, the gear-ratio is less tight and you can still change at below 8000 RPM without droping into the lower cam.

Cheers Phil

alicrozier

562 posts

268 months

Thursday 10th August 2006
quotequote all
Phil-CH said:

At least, 2nd into 3rd, 3rd into 4th, the gear-ratio is less tight and you can still change at below 8000 RPM without droping into the lower cam.

Cheers Phil


No, 2nd to 3rd you still need to be right on the limiter in order to maintain 2nd cam.

It would be good to see the normalised torque curves for the 111R/Exige but I suspect the optimum is to change up right at the limiter in every gear...

Vmax is in 5th gear btw!

Phil-CH

1,132 posts

295 months

Thursday 10th August 2006
quotequote all
alicrozier said:

No, 2nd to 3rd you still need to be right on the limiter in order to maintain 2nd cam.


True, my bad. I was trying to be rather conservative in my reply above which is why I included the 2nd->3rd gear change... You're right though, 2nd->3rd is right at the rev limiter, but it's much easier to get right than 1st->2nd. In fact, accoarding to some calculations I've done, it's not possible to keep it in 2nd cam from 1st into 2nd. You can do it, if you shift at the very latest point before the rev-limiter hits in and work the clutch in the right way (i.e. not droping it).
Going from 2nd into 3rd is a lot more forgiving in comparison...