new Elise, new problems
new Elise, new problems
Author
Discussion

R TOY

Original Poster:

1,747 posts

259 months

Saturday 23rd September 2006
quotequote all
Well a new to me Elise anyway. As the car,2000s1 has been stood for 4months the brake discs were pretty rusted up so we decided to take the discs of ,clean them up and the pads etc. first problem on the fronts was the two fixing bolts holding the caliper to the hub. We managed to release one side with heat and good hex wrench but unfortunately the other side had a bolt already rounded so had to split the caliper(2 of the 4 bolts needing heat treatment to shift). So this turned a 2 hr job into a full morning. Then the rears! One actually went ok but the other side is not gonna be so easy.. Having removed the stupidly tight wheel nuts the wheel still refused to budge. On closer inspection we had only removed 1/2 of two of the nuts leaving the other 1/2 still firmly on the stud. The nuts have sheared leaving the round bevelled section behind making it impossible to remove the wheel. Has anyone had this same problem and what is the remedy? Only two options that we have come up with are 1. anglegrinder on the wheel or 2. Drill the stud out of the nut and fit new studs, (not as easy as it sounds)
Any clever ideas greatly appreciated. Dave.
Inidently this car has done 90k miles! Are there many others about with this kind of mileage?

jondude

2,441 posts

248 months

Saturday 23rd September 2006
quotequote all
If I have understood correctly, and you have a rounded off bolt holding the wheel on, then another option is to use an ( air) impact driver.

These can be had for around £30 at Argos ( I think ) and will always be a great addition to any toolkit.

Other plans Bs are to weld a socket onto the bolt and remove as normal.

Naturally, this won't make you feel much better now, but when you do get this sorted and put it back together again, coppaslip the bolts. I am regularly amazed that people paying up to £1,000 for a basic service get their cars back 'dry bolted ', so to speak.

Be patient. You will get there in the end....and fall in love with coppaslip next time you put the spanner on and the bolts loosen freely!

R TOY

Original Poster:

1,747 posts

259 months

Saturday 23rd September 2006
quotequote all
Thanks for reply. BUT the nut has not rounded off, the top hexagon part of the nut which the socket fits on has sheared from the bottom round part of the nut which is bigger diam and has the coned end to engage the wheel hole. I removed the top section but the bottom piece has remained inside the wheel with 1/2 inch of stud sticking out the end.

NathanK

80 posts

253 months

Saturday 23rd September 2006
quotequote all
Not sure if this will work for you...

I had a Golf with no security tool for the wheels. I took it to a chap who took an acetelyne torch to the nuts and cut them off. He managed it with only a minor singe to the side of the one of the wheels bolt holes.

Better than knackering the wheel if that's the only option!

Arno

349 posts

309 months

Monday 25th September 2006
quotequote all
R TOY said:
We managed to release one side with heat and good hex wrench but unfortunately the other side had a bolt already rounded so had to split the caliper(2 of the 4 bolts needing heat treatment to shift).


Eeeh.. You split the front calipher? As in.. You now have separated the front an rear parts of the calipher?

That's not a good idea.. These are not meant to be taken apart, except by AP themselves, as they use specialised locking compounds when assembling the caliphers and require specific sequences to torque the bolts up to the correct settings.

Only way you should take them off is by undoing the two bolts that screw into the upright.

If one of the heads was rounded then usually you can hammer in a slightly bigger torx bit or something similar, or weld on a second bolt and undo it that way.

You may want to send the slip calipher to AP or Lotus for proper re-assembly.

As to undoing the wheel bolts. Having the remaining head drilled out/off is probably the best option. Once the wheel is off you can then work on the remaining part of the bolt.

Bye, Arno.