S1 tuning to 140-150 bhp??
S1 tuning to 140-150 bhp??
Author
Discussion

aljack

Original Poster:

61 posts

252 months

Wednesday 27th September 2006
quotequote all
Hi everyone
I currently have a standard s1 Elise with an Larini exhaust and a Hurricane induction kit fitted. I am looking to increase the power to around 140-150 BHP but which is the best method to achieve this? Do i have several options?
I have been pricing up the R140 kit, but it seems expensive for what basically is a 52mm throttle body and a set of cams? (£700).
Also would i need to change the suspension set up or place a rear spoiler on the car to increase rear down force, like the 111s??
Thanks!!

TIPPER

2,955 posts

250 months

Wednesday 27th September 2006
quotequote all
Believe it or not there's no straightforward answer to your question. It really depends on what you're looking for from your car and what you are using it for. Apart from PTP have a look at DVA power (sorry I'm no good at linky things) and also kiwirog on Seloc is well respected for his head work.
I've just had a close ratio gearbox fitted to my boggo engined S1 and its transformed the car giving it a much greater sense of urgency and better acceleration where it matters for me. The next oily-bits work I've got planned will probably involve a 52mm throttle body and piper 633 cams plus a bit of work on the inlet manifold to remove moulding flashing. That should give me of the order of 140 bhp which with my C/R box will do me fine (for now). The next step I'd take would be to send the head to either Dave Andrews (dva) or kiwirog for some mild porting work which with the cams should see power rise to about 155 bhp. A 4-2-1 exhaust downpipe would also be worthwhile to maximise torque. Much more than that and the bottom of the engine will need attention, particularly the pistons.
With regards the suspension, again depends on what you're looking for. For road use I'm happy with the standard set up but when the konis give out I'll be upgrading to the S2 Bilstein set-up. If I were tracking the car regularly I'd probably be looking towards either Nitrons or Ohlins. Don't forget that a proper geo will probably trasform your car if it hasn't been done for a while.
Not sure about the extra spoiler but I'm sure someone will be along to comment (and disagree with me!!)

s111dpc

1,519 posts

260 months

Wednesday 27th September 2006
quotequote all
But a 111s instead?

Sorry, it had to be said rolleyes

S works

10,166 posts

281 months

Wednesday 27th September 2006
quotequote all
What Tipper said, personally I'd go for a 4-2-1 first and see how that improves things. IF you go for new cams etc. you'll want an Emerald to remap it and you're soon going into territory where the money you spend you'll never get back.

If you really want more power then as mentioned, sell up and get a 111S or a Sport 160.

clanger

1,087 posts

289 months

Thursday 28th September 2006
quotequote all
Get to the scrappers and buy a MG VVC engine with all ancillaries and ecu (pay approx £750) and sell your engine and bits for £400 - 118bhp to 145bhp for £350...

garydvo

432 posts

269 months

Thursday 28th September 2006
quotequote all
Kiwirog on here and seloc he will give you good advice on getting it above 150 Bhp. Also DVA as well. The head on the K is basically a 1.4 head and needs to be ported to make it breath. Add a 4-2-1 with the larni and you are on your way, thats what Roger told me anyway.

S2 suspension is a must steveb on Seloc.

This VVC idea from a junk yard is a bit of a long winded way of doing it. I belive the standard K with mods gives more flexability than the VVC. Is the VHPD 190 Bhp a VVC I think not.

S Works

10,166 posts

281 months

Thursday 28th September 2006
quotequote all
VVC is probably a quicker route upto around 160bhp (assuming it's an S2 version), but beyond that yeah you're right. It's limited in application AFAIK.

LovelyLara

41 posts

256 months

Thursday 28th September 2006
quotequote all
I bought mine with a 140 upgrade which was a chip from BBR and a "different" downpipe (can't remember the details - it was 8 years ago and its been changed again since.....).

Could do no harm to give BBR a call? They're in Brackley, Northants.

clanger

1,087 posts

289 months

Thursday 28th September 2006
quotequote all
Sorry I thought that 140 to 150bhp was being asked for

The VHPD head was a one off casting. The VVC head(by undertaking the necessary mods - relatively straightforward) can be used on standard engines and is a much better valved ported head than the std..

The VVC engine offers reliable,unmodded 145ish bhp - engine out, 2nd hand back engine in - days job...

rfoster

1,482 posts

285 months

Thursday 28th September 2006
quotequote all
clanger said:
Sorry I thought that 140 to 150bhp was being asked for

The VHPD head was a one off casting. The VVC head(by undertaking the necessary mods - relatively straightforward) can be used on standard engines and is a much better valved ported head than the std..

The VVC engine offers reliable,unmodded 145ish bhp - engine out, 2nd hand back engine in - days job...



Pretty sure you will need a new engine cover as well - they're higher up on the 111S than the standard car. Best suggestion here? Buy a 111S or a modded car. I had a '98' STD with a B&C Super 160 engine upgrade, the conversion was £3k + VAT but second hand they don't realise much more than a standard car. Gives around 145 bhp and very smooth too. Try a few & see what you prefer.

clanger

1,087 posts

289 months

Thursday 28th September 2006
quotequote all
Quite right that man about the engine cover

aljack

Original Poster:

61 posts

252 months

Thursday 28th September 2006
quotequote all
Thanks for all the advice, i may contemplate selling her for a 111s

TIPPER

2,955 posts

250 months

Thursday 28th September 2006
quotequote all
S works said:
What Tipper said, personally I'd go for a 4-2-1 first and see how that improves things. IF you go for new cams etc. you'll want an Emerald to remap it and you're soon going into territory where the money you spend you'll never get back.

If you really want more power then as mentioned, sell up and get a 111S or a Sport 160.


Not necessarily so Tim. Dave Andrews' K13A kit comprises ported head and 633 cams (amongst other things) and single vernier (with second as an option)and works with the standard MEMS unit to produce 155 bhp. Most important with cam upgrades is getting them timed correctly thus the verniers.

S works

10,166 posts

281 months

Thursday 28th September 2006
quotequote all
But to properly time everything one vernier isn't going to be enough. Sure you can piss about with a load of cash, get the verniers, cams and Emerald, but to get it running properly, and get the best improvement you need to get it set-up on an RR surely?

There's no shortcuts as far as I've seen. One of the reasons I went for the S160 was exactly that. It provides a good base for going bigger if you want to.

TIPPER

2,955 posts

250 months

Thursday 28th September 2006
quotequote all
Fair comment Tim. I'm working on a bit by bit basis with my car. I'll probably go for some 633 cams (with verniers) next then maybe DVA or kiwirog head and then an emerald together with a 4-2-1 at some stage. I may just call a halt at some stage - who knows? The point is for me that I can upgrade the car as funds allow and get some fun planning the project. Resale isn't really an issue to me as I intend keeping the car for quite a few years and regard the car as my 'hobby'. I used to chuck far, far more money away on my (small) racing yacht (no time for that with young kids!).

S works

10,166 posts

281 months

Thursday 28th September 2006
quotequote all
Which is how many do it dude, and it's a considered, proven and measured way of making sure every £ counts in the right direction.

Don't get me wrong, my contention is just that if you want to make a quick leap (and I'm an impatient bugger as you probably can tell!) there's no real shortcuts.

tuscan_thunder

1,763 posts

277 months

Friday 29th September 2006
quotequote all
aljack said:
Hi everyone
I currently have a standard s1 Elise with an Larini exhaust and a Hurricane induction kit fitted. I am looking to increase the power to around 140-150 BHP but which is the best method to achieve this? Do i have several options?
I have been pricing up the R140 kit, but it seems expensive for what basically is a 52mm throttle body and a set of cams? (£700).
Also would i need to change the suspension set up or place a rear spoiler on the car to increase rear down force, like the 111s??
Thanks!!


If it was me, I'd look at a driver training day, some very sticky tyres and some suspensions mods, then consider more power. That said, my 135 engine is a nice wee upgrade.

aljack

Original Poster:

61 posts

252 months

Saturday 30th September 2006
quotequote all
Cheers Tipper!
DVA power offer some impressive packages, i think my money will go in their direction (145HP kit) then get it on the RR. The advice on the driving training is imperative but i am currently emergency response trained. I also agree that to get the most from a purist car such as the Elise, every owner should have some form of driver training before they increase the BHP. Thanks!

Hollywood Wheels

3,689 posts

261 months

Saturday 30th September 2006
quotequote all
S works said:


If you really want more power then as mentioned, sell up and get a Sport 160.


yes Oh Yes!! evil

Suckmychrsitmas

654 posts

260 months

Sunday 13th May 2007
quotequote all
Anyone have any experience of the PTP 140bhp upgrade?

Also, is the spoiler from the 111S available for the standard S1?