BoLOCs to Break Pads!!
BoLOCs to Break Pads!!
Author
Discussion

Bing o

Original Poster:

15,184 posts

250 months

Tuesday 10th April 2007
quotequote all
Well, I've finally killed off my brake pads, which are now softer than Jade Goody's head, and have a fishy smelling set of Mintex 1144s to go on, but:

1) I have no facilities to change the pads

2) I have little technical ability either.

So which bored BoLOC wants to earn some beer tokens helping me replace them (jack and knowledge of how to do it essential).

I am around all week, so please advise availabilty and beer preference below....

Cheers BoLOCs!!

philygumbo

1,500 posts

280 months

Tuesday 10th April 2007
quotequote all
Brake pads are a piece of piss.
I am not free until Friday but if you are not too far away Friday pm?
Unless another BoLOC is available earlier.
South coast is a big area where exactly?

Stewart rush

93 posts

237 months

Tuesday 10th April 2007
quotequote all
I'm just north of Portsmouth, so if your're anywhere near there I can help any evening....Its only a 5 min job to do the fronts!

Cheers

Stew

shangani

3,069 posts

268 months

Tuesday 10th April 2007
quotequote all
To change brake pads, you need minimal tools:

1) Jack
2) Spanner for wheelnuts (17 goes on the locknut tool)
3) Needlenose pliars
4) 8mm allen key

That's it and it is a very easy job even if you are not mechanically minded. This will take you through it:

http://elise-faq.info/index.php?title

Bing o

Original Poster:

15,184 posts

250 months

Tuesday 10th April 2007
quotequote all
shangani said:
To change brake pads, you need minimal tools:

1) Jack
2) Spanner for wheelnuts (17 goes on the locknut tool)
3) Needlenose pliars
4) 8mm allen key


hmm, of all those, I have the Allen Key!!

I may try a mates garage if no-one around Bournemouth is free before Friday (off to Cornwall then).

Oh wll, back to teh clay bar for me today then!!

bertie

8,569 posts

315 months

Tuesday 10th April 2007
quotequote all
Bing o said:
shangani said:
To change brake pads, you need minimal tools:

1) Jack
2) Spanner for wheelnuts (17 goes on the locknut tool)
3) Needlenose pliars
4) 8mm allen key


hmm, of all those, I have the Allen Key!!

I may try a mates garage if no-one around Bournemouth is free before Friday (off to Cornwall then).

Oh wll, back to teh clay bar for me today then!!


And as far as I recall from doing mine (twice) , you don't need an allen key.

shangani

3,069 posts

268 months

Tuesday 10th April 2007
quotequote all
You do not absolutely have to use an allen key, but it makes the fronts a lot easier, especially if you have a big lip on the disc. Besides, only half a minute to remove the caliper with an allen key driver.

bertie

8,569 posts

315 months

Tuesday 10th April 2007
quotequote all
But removing the rear caliper is a 17mm spanner job????

The fronts you never need to remove as you can just push the pistons back.

Sorry, just re-read and noticed you do mean the fronts.


Edited by bertie on Tuesday 10th April 17:22

Gooby

9,269 posts

265 months

Tuesday 10th April 2007
quotequote all
Sorry chap - I know I said I would help but my week has exploded. I am chasing around after 2 builders and I have interviews....

Bing o

Original Poster:

15,184 posts

250 months

Sunday 15th April 2007
quotequote all
Hi all,

Just wondered if anyone around the Bournemouth area was free to help this evening or next week evening (after about 7.30)?

Cheers

Bingo