Discussion
As not all of you visit SELOC I though i'd post this up here too...I hope people don't mind
Well today I finally plucked up the courage to give my S1 a little service. I took a few pics along the way with my phone so please excuse the quality
The bits...
Oil supplied by Opie Oils and the rest of the bits were supplied by Geary @ Eliseparts.
First things first, lets get the car in the air!
Plenty of room to work now
A few mins the under trays were off and it was time to have a nose around under the car.
Uniball kit fitted to my ali uprights
Frayed flexi pipe
Quickly bodged with a jubilee
After crawing back out from under the car I carefully drove the car off the ramps and took it for a quick spin to get the oil nice and warm.
:brum
20 mins later the car was back on the ramps and the oil was ready to be drained. Before draining I removed the oil filler cap.
Out comes the trusty socket set and the sump plug is undone
Being the tit I am I hadn't placed the oil catch tray in the right place and it soon started to overflow :beat
with the oil all drained it was time to replace the sump bolt and remove the pikey Fram oil filter :up
These come in very handy
Oil filter now removed....
Before screwing on the new filter I primed it with a little fresh oil.
With the filter primed it was time to screw on the new filter without losing too much of the oil
Job done!
Next task was to slosh some oil back into the car...now I'm pretty good at making a mess so I knocked up a make shift funnel
After filling the car with around 4L of Oil I rolled the car onto the flat and checked the level on the dipstick....it was little low so I added some more oil and re-checked until I was happy. I cranked the car over to check all was ok before moving on...
Next......the fuel filter!
To make our lives easier when replacing the fuel filter it's a good idea to remove the pressure from the fuel system. To do this you simply remove the fuel pump fuse and start the car! Once the car has stalled, crank the car over for a few seconds.
You can find the fuel pump fuse located next to the ECU on the left hand side of the boot (unclip the boot bag).
Here's a picture of the fuel filter (without it's plastic holder), he's located on the left hand side of the engine bay. You may find access to the fuel filter and fixings easier if you remove your airfilter/induction kit/air box.
Once the pressure is removed from the system you may undo the fixings at either end of the fuel filter. For this you will need a 15mm & a 19mm open ended spanner.
Ensure you had a container and a few old rags to catch any unused fuel.
I found the bottom fixing too hard to undo without first removing the top one.
Note how much fuel I caught with the container even though the system was de-pressurized :nut
Once free you can unclip the top line (to the engine) using the push to release connector.
Fuel filter now removed...
Next step is to screw in the top fixing on to the new filter (I applied a little copper slip to the tread..not sure if this was a good or a bad move though...comments?)
Repeat the same with the bottom line...
Once all was nipped up tight, I replaced the fuel pump fuse and primed the system by turning the ignition to the first position (You should hear the fuel pump). I then checked for leaks and started the car.
Once happy that there were no leaks I moved onto the easiest task of the day....The Spark Plugs!
The spark plugs and leads are hidden by a plasic cover, this is simply removed by unscrewing 2 screws.
Once the cover is removed, you are left with this...
Pop the plug leads off the plugs one at a time by gently pulling upwards. Once they are removed, tuck them out of the way (not down the back of the engine as they may touch the exhaust manifold).
Next step is to remove the plugs, this is easily done with a 10mm Spark Plug socket, a ratchet and an extension bar.
Repeat the process for all 4 plugs.
Here's a picture of the plugs I removed from my engine....they don't look too pretty!
Pop your new plugs in and nip them up tight...not too tight though!
Once all 4 plugs are in you may replace your plug leads and plug cover.
Start the car and enjoy
If you're happy you have no leaks and the car is running ok, reverse it back onto your ramps and bolt up your under trays
I hope this is informative to some people, it's was my first time doing an oil and filter change so please point out any mistakes or tips etc.
Cheers,
Martyn
Well today I finally plucked up the courage to give my S1 a little service. I took a few pics along the way with my phone so please excuse the quality
The bits...
Oil supplied by Opie Oils and the rest of the bits were supplied by Geary @ Eliseparts.
First things first, lets get the car in the air!
Plenty of room to work now
A few mins the under trays were off and it was time to have a nose around under the car.
Uniball kit fitted to my ali uprights
Frayed flexi pipe
Quickly bodged with a jubilee
After crawing back out from under the car I carefully drove the car off the ramps and took it for a quick spin to get the oil nice and warm.
:brum
20 mins later the car was back on the ramps and the oil was ready to be drained. Before draining I removed the oil filler cap.
Out comes the trusty socket set and the sump plug is undone
Being the tit I am I hadn't placed the oil catch tray in the right place and it soon started to overflow :beat
with the oil all drained it was time to replace the sump bolt and remove the pikey Fram oil filter :up
These come in very handy
Oil filter now removed....
Before screwing on the new filter I primed it with a little fresh oil.
With the filter primed it was time to screw on the new filter without losing too much of the oil
Job done!
Next task was to slosh some oil back into the car...now I'm pretty good at making a mess so I knocked up a make shift funnel
After filling the car with around 4L of Oil I rolled the car onto the flat and checked the level on the dipstick....it was little low so I added some more oil and re-checked until I was happy. I cranked the car over to check all was ok before moving on...
Next......the fuel filter!
To make our lives easier when replacing the fuel filter it's a good idea to remove the pressure from the fuel system. To do this you simply remove the fuel pump fuse and start the car! Once the car has stalled, crank the car over for a few seconds.
You can find the fuel pump fuse located next to the ECU on the left hand side of the boot (unclip the boot bag).
Here's a picture of the fuel filter (without it's plastic holder), he's located on the left hand side of the engine bay. You may find access to the fuel filter and fixings easier if you remove your airfilter/induction kit/air box.
Once the pressure is removed from the system you may undo the fixings at either end of the fuel filter. For this you will need a 15mm & a 19mm open ended spanner.
Ensure you had a container and a few old rags to catch any unused fuel.
I found the bottom fixing too hard to undo without first removing the top one.
Note how much fuel I caught with the container even though the system was de-pressurized :nut
Once free you can unclip the top line (to the engine) using the push to release connector.
Fuel filter now removed...
Next step is to screw in the top fixing on to the new filter (I applied a little copper slip to the tread..not sure if this was a good or a bad move though...comments?)
Repeat the same with the bottom line...
Once all was nipped up tight, I replaced the fuel pump fuse and primed the system by turning the ignition to the first position (You should hear the fuel pump). I then checked for leaks and started the car.
Once happy that there were no leaks I moved onto the easiest task of the day....The Spark Plugs!
The spark plugs and leads are hidden by a plasic cover, this is simply removed by unscrewing 2 screws.
Once the cover is removed, you are left with this...
Pop the plug leads off the plugs one at a time by gently pulling upwards. Once they are removed, tuck them out of the way (not down the back of the engine as they may touch the exhaust manifold).
Next step is to remove the plugs, this is easily done with a 10mm Spark Plug socket, a ratchet and an extension bar.
Repeat the process for all 4 plugs.
Here's a picture of the plugs I removed from my engine....they don't look too pretty!
Pop your new plugs in and nip them up tight...not too tight though!
Once all 4 plugs are in you may replace your plug leads and plug cover.
Start the car and enjoy
If you're happy you have no leaks and the car is running ok, reverse it back onto your ramps and bolt up your under trays
I hope this is informative to some people, it's was my first time doing an oil and filter change so please point out any mistakes or tips etc.
Cheers,
Martyn
Love doing jobs like this..............I do all my own work when possible
The ramps i'm not keen on.............the last time I used them I'd left my back garage door open and the rear clam touched it and cracked
Also I find it hard to get up on them and worry about driving too far back!
I've now taken to driving on small lumps of wood and using the slope on my drive, seems to be enough clearance for most jobs
I've got a great socket set and its worth its weight in gold
Also, Torque wrench..........theres a great satisfaction to be had with one of these knowing you've got things tigtened to OE spec
The only things I can bear to go to a garage for are Geo, Tyres and Service stamp
The ramps i'm not keen on.............the last time I used them I'd left my back garage door open and the rear clam touched it and cracked
Also I find it hard to get up on them and worry about driving too far back! I've now taken to driving on small lumps of wood and using the slope on my drive, seems to be enough clearance for most jobs
I've got a great socket set and its worth its weight in gold
Also, Torque wrench..........theres a great satisfaction to be had with one of these knowing you've got things tigtened to OE spec
The only things I can bear to go to a garage for are Geo, Tyres and Service stamp
Lotustuart said:
Whys the one on the end so mucky!?!?
Doesn`t look quite right. Mine did that when I had HGF, (sorry to worry you martyn) I could very easily be very wrong as I am no mechanic. Any suggestions?
Good work though mate!

Could just be the rocker cover gaskets weeping slightly, might pop the plugs next week to see if that plug goes all grotty too. HGF is an excuse for DVA to work his magic
Cheers for the kind words

Nothing constructive to add Martyn other that what those above have mentioned, but must say that is a top effort
To some it will be quite mundane, but to newbies looking to wield the spanner themselves, then it's always really useful to have something like this
Consider this one 'Janitor Approved'
Edited by Janitor on Friday 27th April 08:50
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff





